A European probe to comet Halley

A European probe to comet Halley is proposed. The probe's model payload consists of 8 scientific instruments, viz. neutral, ion and dust impact mass spectrometers, magnetometer, medium energy ion and electron analyzer, camera, dust impact detectors and plasma wave experiment. Fly-by of the comet Halley nucleus will take place on November 28th, 1985, at about 500 km miss distance. The main spacecraft serves as relay link to transmit the observed data to Earth. As probe, a modified ISEE 2 design is proposed. Because of the cometary dust hazard expected in the coma a heavy dust shield (27 kg) is required, consisting of a thin front sheet and a 3 layer rear sheet. The probe is spin-stabilized (12 rpm), has no active attitude and orbit control capability and uses battery power only to provide about 1000 Wh for a measuring phase. A despun antenna transmits up to 20 kbit/s, in X-band. The total probe mass is estimated at 250 kg. The 3 model development programme should start in mid 1981 with Phase B.     

Measurements of X-ray scattering from interstellar dust

We have examined the surface brightness profiles of four of the brightest compact galactic X-ray sources observed with the Imaging Proportional Counter (IPC) aboard the Einstein Observatory for the existence of halos produced by the scattering of X-rays from interstellar dust. The sources are CYG X-3, 4U1658-48, GX13+1, and 4U1254-69. The halos are apparent when a comparison is made between each source's measured surface brightness profile and a model profile based upon a point response function (PRF) for each source. These model profiles depend upon knowledge of the source's spectrum, which is derived from the IPC itself and corroborated by the Einstein Monitor Proportional Counter and/or previous measurements.As conclusions rest entirely on a knowledge of the system (IPC and Mirror) PRF, we began this study with a comprehensive examination of the calibration data taken for the Observatory prior to launch. Point-source images for both the IPC and the HRI have been analyzed at various energies in order to gain a quantitative understanding of scattering by the mirror surface elements and the IPC's spatial resolution.All four sources show a significant excess above the response from a point-source. The attribution of the excess to X-rays scattered from interstellar dust is strengthened by the positive correlation of the magnitude of this excess with the observed column density of material along the line of sight. Furthermore, we have examined the surface brightness profiles of LMC X-1 and 3C273 and found them to have a greatly reduced excess above their model profiles. Because of their high galactic latitude and because only dust within our own galaxy will lead to the formation of a halo that extends beyond a few arcminutes, only a small effect is expected for these sources.     

Thermal modeling of Halley's comet

The comet thermal model of Weissman and Kieffer is used to calculate gas production rates and other parameters for the 1986 perihelion passage of Halley's Comet. Gas production estimates are very close to revised pre-perihelion estimates by Newburn based on 1910 observations of Halley; the increase in observed gas production post-perihelion may be explained by a variety of factors. The energy contribution from multiply scattered sunlight and thermal emission by coma dust increases the total energy reaching the Halley nucleus at perihelion by a factor of 2.4. The high obliquity of the Halley nucleus found by Sekanina and Larson may help to explain the asymmetry in Halley's gas production rates around perihelion.     

Comparative study of the dust emission of 19P/Borrelly (Deep space 1) and 1P/Halley

Images obtained by the Miniature Integrated Camera and Imaging Spectrometer (MICAS) experiment onboard the Deep Space 1 spacecraft which encountered comet 19P/Borrelly on September 22nd 2001 show a dust coma dominated by jets. In particular a major collimated dust jet on the sunward side of the nucleus was observed. Our approach to analyse these features is to integrate the observed intensity in concentric envelopes around the nucleus. The same procedures has been used on the Halley Multicolour Camera images of comet 1P/Halley acquired on March 14th 1986. We are able to show that at Borrelly the dust brightness dependence as a function of radial distance is different to that of Halley. At large distances both comets show constant values as the size of the concentric envelopes increases (as one would expect for force free radial outflow). For Halley the integral decreases as one gets closer to the nucleus. Borrelly shows opposite behaviour. The main cause for Halley's intensity distribution is either high optical thickness or particle fragmentation. For Borrelly, we have constructed a simple model of the brightness distribution near the nucleus. This indicates that the influence of deviations from point source geometry is insufficient to explain the observed steepening of the intensity profile close to the nucleus. Dust acceleration or fragmentation into submicron particles appear to be required. We also estimate the dust production rate of Borrelly with respect to Halley and compare their dust to gas ratios.     

A proportional counter/image intensifier system for the detection of low energy X-rays

Proportional counters (PC's) and gas scintillation proportional counters (GSPC's) currently used for detection of low energy X-rays provide information on event position and energy. Although at 1.5 keV PC's have good position resolution (～ 200 μm FWHM) they have relatively poor energy resolution (～ 40% FWHM). Conversely GSPC's have reasonable energy resolution (～ 20% FWHM), but poor spatial resolution (～ 1mm FWHM).We describe a scheme in which a parallel plate PC with a transparent anode deposited on a fibre optic substrate has been used. This allows the light emitted by electron avalanches caused by X-ray events in the PC to be detected by an image intensifier with electronic readout. Using this scheme spatial resolution better than that of conventional PC's should be attainable. In addition avalanches induced by single electrons can be resolved through observation of the time structure of the light flash. Using the ability to count the number of primary electrons created by each X-ray event, it is shown that energy resolution can be achieved which is comparable to that of the GSPC.     

A quantitative model for comet nucleus topography

Topography of the surface of a comet nucleus is likely rough at all scales smaller than the mean effective radius. We present a flexible and easily scalable model for quantitative calculations simulating the effects of comet nucleus topography on gas release and dust mantle evolution. The topographic features we describe must be large enough (typically> 10 m) so that they will not erode in one orbit of the nucleus around the Sun. The maximum effective size of a hill is about 1/√2 times the effective radius of the nucleus. If it is larger, then an ellipsoidal shape of the nucleus is more appropriate. The procedure described here also permits for inhomogeneous composition of the topographic features, leading to locally different rates of gas production (e.g., jet-like features and filaments) or different thicknesses of the dust mantle. It also can give rise to different temperature patches, locally varying albedos and emissivities, and may explain the formation of permanent dust mantles.     

Models of P/Borrelly: Activity and dust mantle formation

Comet 19P/Borrelly was observed by Deep Space One spacecraft on September 22, 2001 (Soderblom et al., 2002).The DS1 images show a very dark and elongate nucleus with a complex topography; the IR spectra show a strong red-ward slope consistent with a very hot and dry surface (345K to 300K). During DS1 encounter the comet coma was dominated by a prominent jet but most of the comet was inactive, confirming the Earth-based observations that <10% of the surface is actively sublimating. We have developed a thermal evolution model of comet PBorrelly, using a numerical code that is able to solve the heat conduction and gas diffusion equations at the same time across an idealized spherical nucleus ( De Sanctis et al., 1999, 2000; Capria et al., 2000; Coradini et al., 1997a,b). The comet nucleus is composed by water, volatiles ices and dust in different proportions. The refractory component is made by grains that are embedded in the icy matrix. The code is able to account for the dust release, contributing to the dust flux, and the formation of dust mantles on the comet surface. The model was applied to a cometary nucleus with the estimated physical and dynamical characteristics of P/Borrelly in order to infer the status and activity level of a body on such an orbit during the DS1 observation. The comet gas flux, differentiation and thermal behavior were simulated and reproduced. The model results are in good agreement with the DS1 flyby results and the ground based observations, in terms of activity, dust coverage and temperatures of the surface.     

The Giotto mission to Halley''s comet

ESA's Giotto mission to Halley's comet is a fast flyby in March 1986, about four weeks after the comet's perihelion passage when it is most active. The scientific payload comprises 10 experiments with a total mass of about 60 kg: a camera for imaging the comet nucleus, three mass spectrometers for analysis of the elemental and isotopic composition of the cometary gas and dust environment, various dust impact detectors, a photopolarimeter for measurements of the coma brightness, and a set of plasma instruments for studies of the solar wind/comet interaction. In view of the high flyby velocity of 68 km/s the experiment active time is very short (only 4 hours) and all data are transmitted back to Earth in real time at a rate of 40 kbps. The Giotto spacecraft is spin-stabilised with a despun high gain parabolic dish antenna inclined at 44.3° to point at the Earth during the encounter while a specially designed dual-sheet bumper shield at the other end protects the spacecraft from being destroyed by hypervelocity dust impacts. The mission will probably end near the point of closest approach to the nucleus when the spacecraft attitude will be severely perturbed by impacting dust particles leading to a loss of the telecommunications link.     

Effects of electrostatic forces on the vertical structure of planetary rings

We have calculated the vertical structure of planetary dust rings as it results from a balance between an electrostatic force on the dust grains and the vertical component of the gravitational force from the central planet. The electrostatic force results from the charging of the dust grains by the ambient plasma and a large scale electric field due to a shielding electric field and the resulting vertical dust distribution are strongly dependent on dust size, dust and plasma density, plasma temperature and plasma ion type. The dust density distribution has a different dependence on these parameters in tenuous and in dense dust rings. We solve the relevant equations numerically and also by linearization in the limiting cases of tenuous or dense rings. Our results indicate that the effects treated in this paper may be important in both Jupiter's and Saturn's rings.     

Collection of cometary dust

Rendezvous Missions to Comets lead to low velocities at the nucleus of the comet. The resulting impact velocity of the cometary dust on a target will range between 10 and 400 m/s. The dust particle which impacts on a target can be collected for a subsequent in-situ analysis.

The collection efficiency of a target depends in addition to obvious geometrical conditions upon the surface of the target. The surface characteristics can be divided into two groups:

• “dirty” surfaces, covered with silicate or hydrocarbon compounds (for example vacuum grease),

• “clean” surfaces, like gold (with additional sputtering).

This paper deals with the experimental and theoretical investigation of the collection efficiency of “clean” targets. Laboratory experiments are described which were conducted at the Technische Universität München, Lehrstuhl für Raumfahrttechnik, and the Max-Planck-Institut für Kernphysik, Heidelberg. In both experiments an electromagnetic accelerator is used to accelerate different types of dust in vacuum to velocities between 10 and 400 m/s.

The target is then examined under the microscope and a secondary ion mass spectrometer (which is a model of the laboratory carried on board of the spacecraft for “in situ” analysis). The adhesion of the dust grains at the target is evaluated experimentally in an ultracentrifuge.     

Cometary atmosphere (gas and dust)

There is important progress now in the identifications and measurements of primary (parent) molecules in the inner coma of Comet Halley. H₂O, CO₂ and CO are definitely in the list, CH and some complicate organic molecules are suspected. Gas production rate for water vapor is Q_H2O 10³⁰ s⁻¹. The bulk of data doesn't contradict to the Whipple model of nucleus (with clathrate modification). Pronounced spatial structure of gaseous flow in the coma was observed, but in general measured properties of neutral gas in the coma of Comet Halley are not very different from predicted. Situation for dust is different. In situ dust measurements show that size spectrum and optical properties of particles in coma are substantively declining from predicted on the base of groundbased photometry. However there are discrepancies between Vega and Giotto dust counter data. Dust in the inner coma didn't prevent the succesful imaging of nucleus by TV on Vega 1 and 2.     

Planetary rings: 2–23 centuries of nearly total ignorance, 4 years of information explosion

Saturn lies at nearly twice Jupiter's distance from the Sun and nearly all parts of its system are characterized by much smaller scales than those which are important in the case of Jupiter. This appears in the structures of the planet's atmosphere, in the sizes of classical satellites other than Titan vis-à-vis those of the Galilean satellites, in the plethora of small Saturnian satellites, especially Lagrangian co-orbiters, in the structure of Saturn's F-Ring as contrasted with that of Jupiter's Ring and finally in the highly structured detail in Saturn's Rings, much finer than seriously considered in past theoretical discussions. Uranus' Rings were unknown until five years ago. The discovery and observation of these rings have revived contributions to theory originally intended for application to Saturn's Rings. Models have also been generated for eccentric rings for application to Uranus' Rings which also apply to those of Saturn. These two classes of model are reviewed in the present paper along with the first tentative steps made down the road to unravelling the complexity of Saturn's Rings.     

Determination of the mean dynamic ocean topography model through combining multi-source gravity data and DTU15 MSS around China's coast

Mean dynamic ocean topography (or MDT) is closely related to ocean circulation and global climate change. It has important scientific significance and application value for the development and utilization of marine resources in China's coastal areas. Based on the terrain gravity, marine gravity, and SRTM 3?s data, an algorithm to reduce the problem of gravity data gaps between land and sea is proposed. A consistent land-sea gravity model is established based on point-mass fusion method. Then geoid model, which accuracy was estimated to be 8.5?cm through the verification of 348 GNSS/level data from the coastal provinces, of China's coastal areas was calculated through remove-restore technique. Connecting the above geoid model with DTU15 MSS model to establish a MDT model in China's coastal areas using the direct method in space domain. The effect of gravity field model, dominant factors of sea surface topography, and low pass filter are analyzed. Taking Bohai Sea and Yellow Sea as an example, and comparing MDT with the two international models CNES_2013_MDT and DTU15_MDT. The results show that the MDT has the potential to construct a vertical datum of the ocean and carry out related scientific research and application.     

Mass loading of planetary atmospheres by rocky satellites—II: Transport and enhanced lifetimes of satellite ejecta in planetary magnetospheres

Extensive studies have been conducted concerning individual mass, temporal and positional distribution of submicron rocky ejecta existing in the satellite-planetary gravitational sphere of influence. The transit time of the major portion of the ejecta that is transported from the satellite's gravitational sphere of influence to the planetary magnetopause is about one week and represents a mass loading pulse occurring each satellite orbit. The mass-flux distributions of lunar ejecta at the surface of the magnetopause for a complete lunar orbit are presented. Spatial mass densities of lunar ejecta in specific zones of the magnetosphere provide a means to compare sporadic interplanetary dust spatial mass densities in the same zones.     

Formation of Saturn's spokes

The scattering properties of the spokes in Saturn's rings suggest that they consist of micron-sized dust particles. We suggest that these grains are elevated above the ring plane by electrostatic charging. We show that electrostatic levitation requires a sufficiently large plasma density near the rings. If the plasma density near the rings exceeds a few 10² cm^?3 levitation may occur at significant rates in the strong electric fields which exist in the wall-sheaths at the ring. Once the dust particles are elevated they drift relative to the plasma (except at synchronous orbit). This relative motion constitutes a current which causes a polarization electric field if the plasma is azimuthally inhomogeneous. The dense plasma will drift radially in response to this electric field and cause levitation of more dust particles as it moves along. It leaves a radially aligned trail of elevated dust particles—the spokes. One way of producing dense plasma is by meteor impact on the rings. We discuss the mechanisms of ring charging, electrostatic levitation and the currents in the plasma-dust mixture. We show that for reasonable conditions spokes of more than 10,000 km radial length can be formed in less than five minutes. We also show that under the same conditions the electrostatic levitation model predicts a dust grain population which peaks at a size of 0.6 microns and can reach optical depths of 0.1.     

Synchrotron radiation as a probe of the inner magnetosphere of Jupiter

A short review is given on the characteristics of Jupiter's inner magnetosphere derived from radio observations in the decimetric wavelength range. A comparison of the data with sophisticated model calculations yields information on the magnetic field configuration and the electron distribution, its density, energy spectrum, and pitch angle dependence as a function of spatial coordinates. The latter information can be used to derive e.g. the radial diffusion parameters plus the effects of the satellites, Jupiter's ring, and wave-particle interactions upon the electron distribution.     

The effect of aerosols on climate and aerosol climatology on the basis of observations from space

Principal aspects of the effect of aerosols on climate are discussed and the possibilities of obtaining a climatic data set of global aerosols are analyzed. Based on the analysis of space images, new data have been obtained on gigantic dust outbreaks in various regions of the Earth. It has been shown that dust outbreaks can propagate over hundreds and sometimes thousands of kilometers. The western Sahara - Atlantic Ocean is the major region of propagation of these outbreaks. The continent-to-continent trajectories of dust clouds have been discovered (from Africa to the coast of America, from Central Asia to the Pacific Ocean). Maps of the sources of strong dust transformations have been studied and drawn. In particular, an anthropogenic dust source has been found out on the northeastern coast of the Aral Sea. A striped mesostructure of dust formations has been analyzed, determined by both the inhomogeneous surface and peculiarities of the eddy dust transport. The techniques have been discussed in detail for retrieving the parameters of aerosol size distribution and the vertical profiles of the coefficients of aerosol extinction in the stratosphere and lower mesosphere from the data on the brightness of the twilight and daytime horizon as well as occultation measurements of solar radiation attenuation by the atmosphere.The difficulty of reliably predicting possible environmental changes arises both from the problems of estimating complex interactions of numerous processes and from a lack of information concerning various environmental parameters. For example, an important factor in present day climatic changes is the increased dust content of the atmosphere due to man's activities. However, a reliable estimate of this influence is found to be impossible due to the absence of definitive data on the global distribution of atmospheric dust and the properties of dust in various parts of the world [4,5,13–15]. The impact of aerosols on climate has been discussed in detail in a number of monographs [12–15].Observations from space have opened up new possibilities for studying atmospheric dust. For this purpose, both the imagery and spectrometry of the Earth's atmosphere from space are used. Rather attractive are the prospects for laser sounding [1].     

A transient MHD model applicable for the source of solar cosmic ray acceleration

A two-dimensional, time-dependent magnetohydrodynamic (MHD) model is used to describe the possible mechanisms for the source of solar cosmic ray acceleration following a solar flare. The hypothesis is based on the propagation of fast mode MHD shocks following a sudden release of energy. This model has already been used with some success for simulation of some major features of type II shocks and white light coronal transients. In this presentation, we have studied the effects of initial magnetic topology and strength on the formation of MHD shocks. We consider the plasma beta (thermal pressure/magnetic pressure) as a measure of the $\text{initial}$, relative strength of the field. During dynamic mass motion, the Alfvén Mach number is the more appropriate measure of the magnetic field's ability to control the outward motion. We suggest that this model (computed self-consistently) provides the shock wave and the disturbed mass motion behind it as likely sources for solar cosmic ray acceleration.     

Orbital dynamics of magnetospherically trapped lunar ejecta

$\text{In situ}$ measurements by dust experiments on HEOS II showed significant enhancement of fluxes for submicron particles. Recent studies have shown that lunar ejecta in this size range can, in a highly simplified model, be trapped in the earth's magnetosphere. The present work is a more detailed study of the dynamics of lunar ejecta in the magnetosphere. The particle size ranges for which the guiding center approximation is valid, for which corotation is negligible, and for which electromagnetic forces dominate gravitational forces have been calculated. Temporal details of charge acquisition by ejecta in the plasmasphere are considered.