Lunar exosphere influence on lunar-based near-ultraviolet astronomical observations

The potential effect of the lunar exosphere on the near-ultraviolet sky background emission is predicted for Lunar-based Ultraviolet Telescope (LUT: a funded Chinese scientific payload for the Chang’e-III mission). Using the upper limit on the OH concentration inferred from the recent MIP CHACE results, our calculations show that the sky brightness due to the illuminated exosphere is <8.7 photons⁻¹ cm⁻² arcsec⁻² within the wavelength range 245–340 nm. By evaluating the signal-to-noise ratios of observations of an AB = 13 mag point source at a series of sky background levels, our analysis indicates that the detection performance of LUT can be moderately degraded by the lunar exosphere emission in most cases. An AB = 13 mag point source can still be detected by the telescope at a signal-to-noise ratio more than 8 when the OH concentration is less than 2 × 10⁸ molecules cm⁻³. However, the effect on the performance is considerable when the exosphere is as dense as suggested by CHACE.     

Observation of Mercury’s sodium tail using Fabry–Perot Interferometer

We observed sodium emission from Mercury’s atmosphere using a Fabry–Perot Interferometer at Haleakala Observatory on June 14, 2006. The Fabry–Perot Interferometer was used as a wavelength-tunable filter. The spectra of the surface reflection were subtracted from the observed spectra because sodium emission is contaminated by the surface reflection of Mercury. The image obtained in our observation shows the sodium exosphere extended to the anti-solar direction. The lifetime of a sodium atom was estimated to be 1.6 × 10⁴ to 1.9 × 10⁵ s with an error by a factor of 3–4.     

Antarctic meteor observations using the Davis MST and meteor radars

This paper presents the meteor observations obtained using two radars installed at Davis (68.6°S, 78.0°E), Antarctica. The Davis MST radar was installed primarily for observation of polar mesosphere summer echoes, with additional transmit and receive antennas installed to allow all-sky interferometric meteor radar observations. The Davis meteor radar performs dedicated all-sky interferometric meteor radar observations. The annual count rate variation for both radars peaks in mid-summer and minimizes in early Spring. The height distribution shows significant annual variation, with minimum (maximum) peak heights and maximum (minimum) height widths in early Spring (mid-summer). Although the meteor radar count rate and height distribution variations are consistent with a similar frequency meteor radar operating at Andenes (69.3°N), the peak heights show a much larger variation than at Andenes, while the count rate maximum-to-minimum ratios show a much smaller variation. Investigation of the effects of the temporal sampling parameters suggests that these differences are consistent with the different temporal sampling strategies used by the Davis and Andenes meteor radars. The new radiant mapping procedure of [Jones, J., Jones, W., Meteor radiant activity mapping using single-station radar observations, Mon. Not. R. Astron. Soc., 367(3), 1050–1056, doi: 10.1111/j.1365-2966.2006.10025.x, 2006] is investigated. The technique is used to detect the Southern delta-Aquarid meteor shower, and a previously unknown weak shower. Meteoroid speeds obtained using the Fresnel transform are presented. The diurnal, annual, and height variation of meteoroid speeds are presented, with the results found to be consistent with those obtained using specular meteor radars. Meteoroid speed estimates for echoes identified as Southern delta-Aquarid and Sextantid meteor candidates show good agreement with the theoretical pre-atmospheric speeds of these showers (41 km s⁻¹ and 32 km s⁻¹, respectively). The meteoroid speeds estimated for these showers show decreasing speed with decreasing height, consistent with the effects of meteoroid deceleration. Finally, we illustrate how the new radiant mapping and meteoroid speed techniques can be combined for unambiguous meteor shower detection, and use these techniques to detect a previously unknown weak shower.     

Submicron lunar ejecta in the magnetosphere associated with meteor showers

Recent studies of the lunar ejecta from lunar impacts of interplanetary dust particles indicate that during favorable lunar phases, over 80% of the submicron ejecta enters the earth's magnetosphere. This “pulse” of lunar ejecta produced by the sporadic meteor background will follow the random variations of the sporadic flux. An additional enhancement of this flux can be related to major meteor showers. Since the annual periods of these showers occur during varying lunar phase angles, magnetosphere ejecta flux associated with major showers will vary depending on the coincidence of shower periods and favorable lunar phase angles. The results of an analysis of the “pulse” of ejecta flux in the magnetosphere during the Quadrantids, Geminids, Leonids, and Perseids meteor showers are presented. These results are compared to the satellite measurements of 1959 Eta and HEOS II.     

Hard X-ray continuum from lunar surface: Results from High Energy X-ray spectrometer (HEX) onboard Chandrayaan-1

The High Energy X-ray spectrometer (HEX) on Chandrayaan-1 was designed to study the photon emission in the range of 30–270 keV from naturally occurring radioactive decay of ²³⁸U and ²³²Th series nuclides from the lunar surface. The primary objective of HEX was to study the transport of volatiles on the lunar surface using radon as a tracer and mapping the 46.5 keV line from ²¹⁰Pb, a decay product of ²²²Rn. HEX was tested for two days during the commissioning phase of Chandrayaan-1 and performance of all sub systems was found to be as expected. HEX started collecting science data during the first non-prime imaging season (February–April, 2009) of Chandrayaan-1. Certain anomalies persisted in this data set and the early curtailment of Chandrayaan-1 mission in August, 2009, did not allow any further operation of HEX. Despite these issues, HEX provided the first data set for 30–270 keV continuum emission, averaged over a significant portion of the lunar surface, including the polar region.     

Plasma electron temperature variability in lunar surface potential and in electric field under average solar wind conditions

The Moon is immersed in plasma environment. The most interesting challenge of the lunar plasma– field environment is that it is alternatively dominated by the extended but variable outer atmosphere of the Earth – the magnetosphere – and by the extended but highly variable solar atmosphere – the solar wind. Understanding the plasma environment and its interaction with the lunar surface will be beneficial to both manned and robotic surface exploration activities and to scientific investigations. Presented is a preliminary map of variations of lunar surface electric potential over the day side and night side using probe equations and a discussion on dust dynamics in this E-field structure using the data from Electron Reflectometer in Lunar Prospector spacecraft during 1998–1999. On the day side, potential is around 5 V and on the night side it reaches up to −82 V. On the night side region, only highly energetic electrons can overcome this large negative potential. The variation at electron temperature (T_e) strongly reflects in the surface potential. The potential reaches to a value of −82 V for T_e = 58 eV. Surface charging causes the electrostatic transport of charged dust grains. Dust grain size of 0.1 μm shows a levitation height of 4.92 m on lunar day side, 748 m on terminator region and 3.7 km on the night side. The radius of maximum sized grain to be lofted, R_max, peaks at the terminator region (R_max = 0.83 μm). At the transition region dust levitation is almost absent. This region is most suited for exploration activities as the region is free from hazards caused by lunar dust.     

Flaring loop parameters estimated from solar decimeter type U-like and type J-like fine structures

This work presents the analysis of five fine structures in the solar radio emission, observed between June 2000 and October 2001 by the Brazilian Solar Spectroscope (BSS), in the decimeter frequency band of 950–2500 MHz. Based on their morphological characteristics identified in the dynamic spectra, the fine structures had been classified as type U-like or type J-like bursts. Such emissions are variants of the type III bursts. They support the hypothesis of generation by plasma emission mechanism, from interaction of electron beams accelerated during solar flares, propagating along closed magnetic structures, within the trapped plasma of the solar corona. The spectral and temporal characteristics of the five fine structures had been obtained from the dynamic spectra and the parameters of the agent and the emitting source have been determined, assuming both fundamental and harmonic emissions. The analysis revealed the flux density of the structures is less than 20–80 s.f.u. For assumption of harmonic emission, the interval of values for the source parameters estimated are: the loop size is (0.3–5.1) × 10¹⁰ cm; the electron beam velocity is in the range of 0.16–0.53 c; the temperature of coronal loop top is of the order of (0.25–1.55) × 10⁷ K; and the low limit for the magnetic field is of 7–26 G. These results are in agreement with previous determinations reported in the literature.     

The LAGEOS satellites orbit and Yukawa-like interactions

LAGEOS II general relativity pericenter precession has been analysed in terms of the errors produced by the mismodelling of both the gravitational and non-gravitational perturbations acting on the satellite orbit. The accuracy in the pericenter determination may be considered as an upper-bound value for the estimate of the strength α of a possible new-long-range-interaction described by a Yukawa-like potential. In the present work we have focused on the constraints in α that can be obtained with the current best multi-satellites gravity field model EGM96 (α < 2.6 × 10⁻¹⁰) and also with the first promising models from the CHAMP (α < 1.8 × 10⁻¹⁰) and GRACE (α < 1.2 × 10⁻¹⁰) gravimetric missions. These results represent, potentially, an improvement of two or three orders-of-magnitude with respect to the best constraints obtained in the past with Earth–LAGEOS and Lunar–LAGEOS data (|α| < 10⁻⁵–10⁻⁸). The impact of the non-gravitational perturbations mismodelling in the final error budget has been determined together with the improvements obtainable in the constraint of the strength α with the proposed LARES satellite.     

Variation in the ionospheric propagating factor M(3000)F2 at Ouagadougou,Burkina Faso

We use hourly monthly median values of propagation factor M(3000)F2 data observed at Ouagadougou Ionospheric Observatory (geographic12.4°N, 1.5°W; 5.9^o dip), Burkina Faso (West Africa) during the years Januar1987–December1988 (average F10.7 < 130 × 10⁻²² W/m²/Hz, representative of low solar flux conditions) and for January 1989–December1990 (average F10.7 ? 130 × 10⁻²² W/m²/Hz, representative of high solar epoch) for magnetically quiet conditions to describe local time, seasonal and solar cycle variations of equatorial ionospheric propagation factor M(3000)F2 in the African region. We show that that seasonal trend between solar maximum and solar minimum curves display simple patterns for all seasons and exhibits reasonable disparity with root mean square error (RMSE) of about 0.31, 0.29 and 0.26 for December solstice, June solstice and equinox, respectively. Variability Σ defined by the percentage ratio of the absolute standard deviation to the mean indicates significant dissimilarity for the two solar flux levels. Solar maximum day (10–14 LT) and night (22–02 LT) values show considerable variations than the solar minimum day and night values. We compare our observations with those of the IRI 2007 to validate the prediction capacity of the empirical model. We find that the IRI model tends to underestimate and overestimate the observed values of M(3000)F2, in particular, during June solstice season. There are large discrepancies, mainly during high solar flux equinox and December solstice between dawn and local midnight. On the other hand, IRI provides a slightly better predictions for M(3000)F2 between 0900 and 1500 LT during equinox low and high solar activity and equinox high sunspot number. Our data are of great importance in the area of short-wave telecommunication and ionospheric modeling.     

The water cycle in closed ecological systems: Perspectives from the Biosphere 2 and Laboratory Biosphere systems

To achieve sustainable, healthy closed ecological systems requires solutions to challenges of closing the water cycle – recycling wastewater/irrigation water/soil medium leachate and evaporated water and supplying water of required quality as needed for different needs within the facility. Engineering Biosphere 2, the first multi-biome closed ecological system within a total airtight footprint of 12,700 m² with a combined volume of 200,000 m³ with a total water capacity of some 6 × 10⁶ L of water was especially challenging because it included human inhabitants, their agricultural and technical systems, as well as five analogue ecosystems ranging from rainforest to desert, freshwater ecologies to saltwater systems like mangrove and mini-ocean coral reef ecosystems. By contrast, the Laboratory Biosphere – a small (40 m³ volume) soil-based plant growth facility with a footprint of 15 m² – is a very simplified system, but with similar challenges re salinity management and provision of water quality suitable for plant growth. In Biosphere 2, water needs included supplying potable water for people and domestic animals, irrigation water for a wide variety of food crops, and recycling and recovering soil nutrients from wastewater. In the wilderness biomes, providing adequately low salinity freshwater terrestrial ecosystems and maintaining appropriate salinity and pH in aquatic/marine ecosystems were challenges. The largest reservoirs in Biosphere 2 were the ocean/marsh with some 4 × 10⁶ L, soil with 1 to 2 × 10⁶ l, primary storage tank with 0 to 8 × 10⁵ L and storage tanks for condensate and soil leachate collection and mixing tanks with a capacity of 1.6 × 10⁵ L to supply irrigation for farm and wilderness ecosystems. Other reservoirs were far smaller – humidity in the atmosphere (2 × 10³ L), streams in the rainforest and savannah, and seasonal pools in the desert were orders of magnitude smaller (8 × 10⁴ L). Key technologies included condensation from humidity in the air handlers and from the glass space frame to produce high quality freshwater, wastewater treatment with constructed wetlands and desalination through reverse osmosis and flash evaporation were key to recycling water with appropriate quality throughout the Biosphere 2 facility. Wastewater from all human uses and the domestic animals in Biosphere 2 was treated and recycled through a series of constructed wetlands, which had hydraulic loading of 0.9–1.1 m³ day⁻¹ (240–290 gal d⁻¹). Plant production in the wetland treatment system produced 1210 kg dry weight of emergent and floating aquatic plant wetland which was used as fodder for the domestic animals while remaining nutrients/water was reused as part of the agricultural irrigation supply. There were pools of water with recycling times of days to weeks and others with far longer cycling times within Biosphere 2. By contrast, the Laboratory Biosphere with a total water reservoir of less than 500 L has far quicker cycling rapidity: for example, atmospheric residence time for water vapor was 5–20 min in the Laboratory Biosphere vs. 1–4 h in Biosphere 2, as compared with 9 days in the Earth’s biosphere. Just as in Biosphere 2, humidity in the Laboratory Biosphere amounts to a very small reservoir of water. The amount of water passing through the air in the course of a 12-h operational day is two orders of magnitude greater than the amount stored in the air. Thus, evaporation and condensation collection are vital parts of the recycle system just as in Biosphere 2. The water cycle and sustainable water recycling in closed ecological systems presents problems requiring further research – such as how to control buildup of salinity in materially closed ecosystems and effective ways to retain nutrients in optimal quantity and useable form for plant growth. These issues are common to all closed ecological systems of whatever size, including planet Earth’s biosphere and are relevant to a global environment facing increasing water shortages while maintaining water quality for human and ecosystem health. Modular biospheres offer a test bed where technical methods of resolving these problems can be tested for feasibility.     

Vertical wavenumber spectra of atmospheric ozone measured from ozonesonde observations

Vertical profiles of ozone have been measured at balloon altitudes. Our purpose is to examine the character of vertical wavenumber spectra of ozone fluctuations, to assess the possible roles of gravity wave field in ozone fluctuations, and to determine dominant vertical wavelengths of ozone spectra. Vertical wavenumber spectra of 12 ozone fluctuations obtained during June–August 2003 are presented. Results indicate that mean spectral slopes in the wavenumber range from 4.69 × 10⁻⁴ to 2.50 × 10⁻³ cyc/m are about −2.91 in the troposphere and −2.87 in the lower stratosphere, which is close to the slope of −3 predicted by current gravity wave saturation models. The consistency of the observed spectral slopes with the value of −3 predicted by current gravity wave saturation models suggests that the observed ozone fluctuations are due primarily to atmospheric gravity waves. At m = 1/(1000 m) the mean spectral amplitude is over 30 times larger in the lower stratosphere than in the troposphere. Mean vertical wavenumber spectra in area-preserving form reveal dominant vertical wavelengths of ∼2.6 km in the troposphere and ∼2.7 km in the lower stratosphere, which is consistent with the values varying between 1.5 and 3.0 km estimated from the velocity field and temperature field at these heights.     

Electrostatic gravity gradiometer design for the future mission

Satellite gravity gradiometry has been applied in GOCE mission to obtain higher harmonics of the Earth’s gravity mapping. In-orbit results showed that the precision of GOCE gradiometry achieved a level of 10–20 mE/Hz^1/2 in the bandwidth of 38–100 mHz, and the major error source came from the intrinsic noise of the core sensor electrostatic accelerometer. Two schemes for improving sensitivity of such accelerometer are presented by optimizing the parameters to reduce the dynamic range and choosing the heavier proof mass to suppress the thermal noise limited by the discharging gold wire. As a result, an accelerometer with a better resolution of 6.6×$6.6\times$10⁻¹³ m/s²/Hz^1/2 could be developed, and then a precision of 3 mE/Hz^1/2, corresponding to a spatial resolution of about 78 km half wavelength, is achievable for the future satellite gradiometric mission.     

Gravitational wave detection on the Moon and the moons of Mars

The Moon and the moons of Mars should be extremely quiet seismically and could therefore become sensitive gravitational wave detectors, if instrumented properly. Highly sensitive displacement sensors could be deployed on these planetary bodies to monitor the motion induced by gravitational waves. A superconducting displacement sensor with a 10-kg test mass cooled to 2 K will have an intrinsic instrument noise of 10⁻¹⁶ m Hz^−1/2. These sensors could be tuned to the lowest two quadrupole modes of the body or operated as a wideband detector below its fundamental mode. An interesting frequency range is 0.1–1 Hz, which will be missed by both the ground detectors on the Earth and LISA and would be the best window for searching for stochastic background gravitational waves. Phobos and Deimos have their lowest quadrupole modes at 0.2–0.3 Hz and could offer a sensitivity h_min ? 10⁻²² Hz^−1/2 within their resonance peaks, which is within two orders of magnitude from the goal of the Big Bang Observer (BBO). The lunar and Martian moon detectors would detect many interesting foreground sources in a new frequency window and could serve as a valuable precursor for BBO.     

An in situ laser induced breakdown spectroscope (LIBS) for Chandrayaan-2 rover: Ablation kinetics and emissivity estimations

A miniaturized in situ laser induced breakdown spectroscope-LIBS is one of the two lunar rover payloads to be flown in India’s next lunar mission Chandrayaan-2, with an objective to carry-out a precise qualitative and quantitative elemental analyses of lunar regolith at the proximity of the landing region. As per the imposed mission constraints and the executed design optimization studies, a compact and light-weight LIBS prototype model is developed at our premises. This paper mainly concerns with the estimation of theoretical aspects; especially on evaluation of elemental ablation parameters and signal-to-noise ratio (SNR) calculations for the designed instrument. Theoretical estimations and simulations yielded an incident laser power density of the order of 5 × 10¹⁰ W/cm² on the target surface at a defined lens-to-surface distance (LTSD) of 200 mm and revealed an SNR > 100 for most of the elements under consideration. This paper also addresses the impact of LTSD variation on detection capability. The estimation of plasma-temperatures was carried out utilizing the emission spectra obtained under high vacuum environments employing the LIBS laboratory model. Experimental investigations and the performed theoretical estimations asserted the successful operation of the configured LIBS instrument for in situ elemental analyses on lunar surface.     

Search for antihelium: Progress with BESS

In this paper, we report searches for antihelium in cosmic rays using two recently flown magnetic rigidity spectrometers. BESS-TeV had extended rigidity with an MDR of 1.4 TV and had a flight duration of one day. BESS-Polar was optimized for collecting power. It was flown for 8.5 days and had an MDR of 240 GV. The former flight allows us to explore a previously unexplored rigidity band and the latter flight yields a factor of three improvement in the overall BESS limit. No antihelium candidate was found in the rigidity ranges of 1–500 GV, and 0.6–20 GV, among 7 × 10⁴ events taken with BESS-TeV, and 8 × 10⁶ events taken with BESS-Polar, respectively.     

Cowpeas and pinto beans: Performance and yields of candidate space crops in the laboratory biosphere closed ecological system

An experiment utilizing cowpeas (Vigna unguiculata L.), pinto beans (Phaseolus vulgaris L.) and Apogee ultra-dwarf wheat (Triticum sativa L.) was conducted in the soil-based closed ecological facility, Laboratory Biosphere, from February to May 2005. The lighting regime was 13 h light/11 h dark at a light intensity of 960 μmol m⁻² s⁻¹, 45 mol m⁻² day⁻¹ supplied by high-pressure sodium lamps. The pinto beans and cowpeas were grown at two different planting densities. Pinto bean production was 341.5 g dry seed m⁻² (5.42 g m⁻² day⁻¹) and 579.5 dry seed m⁻² (9.20 g m⁻² day⁻¹) at planted densities of 32.5 plants m⁻² and 37.5 plants m⁻², respectively. Cowpea yielded 187.9 g dry seed m⁻² (2.21 g m⁻² day⁻¹) and 348.8 dry seed m⁻² (4.10 g m⁻² day⁻¹) at planted densities of 20.8 plants m⁻² and 27.7 plants m⁻², respectively. The crop was grown at elevated atmospheric carbon dioxide levels, with levels ranging from 300–3000 ppm daily during the majority of the crop cycle. During early stages (first 10 days) of the crop, CO₂ was allowed to rise to 7860 ppm while soil respiration dominated, and then was brought down by plant photosynthesis. CO₂ was injected 27 times during days 29–71 to replenish CO₂ used by the crop during photosynthesis. Temperature regime was 24–28 °C day/deg 20–24 °C night. Pinto bean matured and was harvested 20 days earlier than is typical for this variety, while the cowpea, which had trouble establishing, took 25 days more for harvest than typical for this variety. Productivity and atmospheric dynamic results of these studies contribute toward the design of an envisioned ground-based test bed prototype Mars base.     

Theoretical modelling of X-ray fluorescence signals for different lunar compositions and dependence on solar activity

We present a forward modelling technique for calculating the surface X-ray spectra for a variety of lunar terrains. Our calculations considered variations in solar fluxes from solar quiescent condition to large flare activity (M1 flare), and expected elemental concentrations in the target, as well as yield, instrumental, and viewing geometry parameters for X-ray induced fluorescence from the lunar surface. Additionally, we present estimates of anticipated XRF signals from prominent K_α lines observable by a collimated 14 cm² X-ray detector from a 100 km lunar orbit with ∼20 km spatial resolution. Our results show that Mg, Al and Si characteristic K_α lines can be observed for all solar conditions. The Ca K_α lines line can be differentiated from a fixed background during more energetic solar conditions such as C1 and M1 flares, whereas Ti and Fe lines are identifiable only during C1 and M1 solar flare conditions for Apollo 12 site composition. Both the K_α X-ray intensity ratios of Mg/Si and Al/Si correlate well with concentration ratios of Mg/Si and Al/Si, respectively, for B1 and M1 solar conditions. The K_α X-ray intensity ratios of Fe/Si and Ca/Si correlates with concentration ratios of Fe/Si and Ca/Si, respectively, for M1 solar condition. In principle, the modelling technique outlined here can be used to determine absolute elemental abundances (Mg, Al, Si, Ca, Ti and Fe) from X-ray spectra measured during recent and future lunar missions.     

Chlorophyll,calcite, and suspended sediment concentrations in the Bay of Bengal and the Arabian Sea at the river mouths

Chlorophyll and suspended sediment concentrations (SSC) and sea surface temperature (SST) are important parameters in assessing the productivity of coastal regions. Numerous rivers flow into the eastern (Ganga, Subernarekha, Mahanadi, Godavari, Krishna, Penner, and Kaveri) and western (Narmada, Tapti, and Indus) coasts of the Indian sub-continent. Using IRS P4 (Oceansat-1) Ocean Color Monitor (OCM) and Moderate Resolution Imaging Spectroradiometer (MODIS) data, we have retrieved chlorophyll, calcite, and SSC near the mouth of these rivers for the period during 2000–2004. The maxima of chlorophyll-a concentrations at the river mouth is much higher for the Himalayan and north India rivers (Ganga, Subernarekha, Mahanadi, and Indus) (10–14 mg/m³) compared to rivers in the southern parts of India (Kaveri and Penner) (∼4 mg/m³). The maxima of calcite concentration (∼45 moles/m³), chlorophyll (∼14 mg/m³), and sediment concentrations (∼9 g/m³) near river mouth are found to be influenced by river discharges (Ganga and Brahmaputra) during the monsoon season. The calcite concentration (∼45 moles/m³) at the mouth of Ganga river shows a major peak with the onset of monsoon season (June–July) followed by a maxima in chlorophyll-a with a time lag of 1–2 months. The Krishna, Kaveri, and Penner rivers show low chlorophyll concentrations (3–8 mg/m³), high calcite (0–40 moles/m³), and low SSC (<3 g/m³) compared to Narmada and Tapti rivers (chlorophyll-a 12–14 mg/m³, calcite 0–2 moles/m³, and SSC 13–19 g/m³). The Indus river shows similar behavior (maxima of chlorophyll ∼13 mg/m³ and SSC ∼8 g/m³) with respect to Ganga river except for high calcite concentration during winter months (∼25 moles/m³). The characteristics of the chlorophyll, calcite, and SSC at the mouth of these rivers show spatial and temporal variability along the eastern and westerns coasts of India which are found to differ widely. A comparison of the chlorophyll concentrations using OCM and MODIS data shows low chlorophyll concentrations in the Bay of Bengal as compared to the Arabian Sea.