高低频复合振动钻削CFRP/钛合金叠层结构试验

针对碳纤维增强复合材料（CFRP）和钛合金叠层结构在传统钻削过程中切削温度高、加工质量差等问题,基于低频振动钻削和高频（超声）振动钻削的优势,提出了高低频复合振动钻削的加工方法。采用自主研制的高低频复合振动钻削装置,对CFRP/钛合金叠层结构进行了制孔试验,对比研究了普通钻削、超声钻削、低频振动钻削和高低频复合振动钻削4种方式下的切削力、钛合金切屑形貌、切削温度和CFRP孔加工质量。结果表明：4种加工方式中,高低频复合振动钻削的轴向力波动相对较大,切削温度显著降低,产生的钛合金切屑呈不连续扇形且整体尺寸最小,CFRP孔出入口及孔壁的损伤程度最低,显著提高了加工质量,为复合材料叠层结构一体化制孔加工提供了指导意义。     

碳纤维与芳纶纤维复合材料机械加工刀具选用

通过对复合材料特性和加工机理的分析,论述了复合材料机械加工对刀具材质、结构和几何参数的要求,介绍了几种适合于碳纤维和芳纶纤维复合材料机械加工的钻削和铣削刀具.     

CFRP-TC4叠层板的钻削实验

采用硬质合金麻花钻对CFRP-TC4叠层板进行钻削试验,分析了钛合金层加工参数对钻削力、钻削温度和加工孔质量的影响。结果表明:随着转速的增加,钛合金层的轴向力逐渐减小;随着钛合金层进给量的增加,钛合金层与CFRP层的轴向力之比逐渐增加。运用指数公式模型对钛合金层轴向力实验结果进行回归分析,得到轴向力与转速以及进给量之间的关系式:F_z=2 088n~(-0.1222)·f_r~(0.2016),并对该方程进行了检验验证,误差均小于10%;在钛合金层进给量不变时,随着钛合金层转速的增加,CFRP的最大烧伤环直径和层间最高温度逐渐增加。     

CFRP/TC4叠层结构钻削仿真与实验研究

为探究CFRP/TC4叠层结构不同叠层顺序下的材料去除过程、两相材料及界面损伤形成机理,建立CFRP/TC4叠层结构钻削的有限元模型,并通过实验获得的轴向力、缺陷类型验证了模型的正确性。研究结果表明,当钻削顺序为CFRP→TC4时,CFRP入口处产生以撕裂型为主的入口分层,CFRP出口处未产生明显的推出分层,但在钻头的持续旋转作用下形成界面分层;当钻削顺序为TC4→CFRP时,当钛合金待切削层厚度较低时,轴向推力超过CFRP层间界面结合强度时产生界面相失效,TC4→CFRP的界面损伤比CFRP→TC4更加严重;TC4→CFRP主要形成以张开型、滑开型裂纹扩展为主的推出分层。     

CFRP/钛合金叠层材料制孔技术的现状与展望

综述了近年来国内外对CFRP/钛合金叠层材料制孔技术的研究进展,重点介绍了传统方法钻削CFRP/钛合金叠层材料过程中轴向力和扭矩、钻削温度的测量方法,轴向力和扭矩的变化规律,以及刀具磨损、加工损伤与钻削工艺的关系;对螺旋铣孔、低频振动钻孔和超声辅助振动钻孔的实现方法、运动特点和加工质量进行了分析总结,并对CFRP/钛合金叠层材料制孔技术的应用和研究动向进行了探讨。     

Enhanced electrothermal effect of carbon fibrous composites decorated with high conductive carbon nanotube webs

Literature has demonstrated that Carbon Nanotubes (CNTs) can greatly enhance the electrical conductivity and matrix-dominated mechanical properties of fibrous composites. However, electrothermal coupling effect of CNTs on Carbon Fiber Reinforced Plastics (CFRPs) has scarcely been considered. This work prepared and introduced thin and porous CNT webs to the surface or/and interface of a CFRP to enhance its electrothermal properties. The results show that CNT webs can enhance the transverse electrical conductivities of the CFRP by 231%−519% in a current range of 50–150 mA, when compared to the base-CFRP. Also, the surface temperature of CNT webs decorated CFRP can be improved by 20.5–32.3 °C within 3 min showing a self-heating rate of 6.8–10.8 °C/min just with an applied voltage of 20–30 V, increased by 152%−177% when compared to the base-CFRP (2.7–3.9 °C/min). Also, deicing can be finished within 4–10 min with a voltage of 18 V and an input power of 246 W/m². Moreover, the electrothermal processes nearly have no negative effect on the mechanical properties of the CFRP. The relatively low input power and short response time for deicing make the CNT webs decorated CFRP may be a potential new generation for aeronautical deicing structure.     

复合材料湿法加工工艺

针对碳纤维增强复合材料干法加工的固有缺点,提出了一种采用水溶性冷却液加工碳纤维增强复合材料的加工工艺,并对干法和湿法加工进行了对比分析。结果表明:湿法加工不影响碳纤维增强复合材料的力学性能,且能够提高加工表面质量及效率,减少刀具磨损,是碳纤维复合材料加工较好的工艺。     

钛合金加工表面完整性的研究现状与展望

钛合金作为航空发动机等高端装备零部件的关键材料,具有良好的高比强度、优异的抗腐蚀性与超强的断裂韧性与疲劳性能.作为典型的航空难加工材料,钛合金在制造过程中引起的表面完整性对其服役性能与可靠性有着至关重要的影响.为此,从切削加工、磨削加工、复合加工与特种加工4个工艺角度对钛合金制造过程中表面完整性的研究现状进行详细阐述....     

碳纤维复合材料孔加工质量试验研究

碳纤维复合材料零件上存在大量的装配工艺孔,采用传统孔加工方式过程中容易导致分层、纤维
撕裂等缺陷. 本文通过钻削和螺旋铣削方式加工碳纤维复合材料(CFRP),对比两种孔加工方法的加工质量,
分析了缺陷存在的原因,发现在碳纤维复合材料上采用螺旋铣削制孔方式是可行的,对碳纤维复合材料孔加工
工艺具有一定的参考价值。     

Effect of hygrothermal aging on moisture diffusion and tensile behavior of CFRP composite laminates

Carbon Fiber Reinforced Polymer (CFRP) composites are widely used in aircraft structures, because of their superior mechanical and lightweight properties. CFRP composites are often exposed to hygrothermal environments in service. Temperature and moisture can affect the material properties of composites. In order to make clear the moisture diffusion behavior and the properties degradation of composites, the TG800/E207 composite laminates with four stacking sequences [0]₁₆, [90]₁₆, [±45]_4s, and [(+45/0/0/–45)_s]_s are designed and manufactured. Moisture absorption tests are carried out at 80 ℃, 90 %RH. It is shown that the moisture absorption curves of composite laminates present a three-stage. A modified Fickian model was proposed to capture the diffusion behavior of TG800/E207 composite laminates. The relationships among the non-Fickian parameters, the environmental parameters and the stacking sequences of CFRP were correlated and compared. Results showed that the modified Fickian curve is sensitive to the diffusivity of Stage I and Stage II. Compared with unaged specimens, the maximum tensile stress for [0]₁₆, [90]₁₆, [±45]_4s, and [(+45/0/0/–45)_s]_s decreased by 14.94 %, 28.15 %, 11.96 %, and 26.36 %, respectively. The strains at failure for [0]₁₆, [90]₁₆, [±45]_4s, and [(+45/0/0/–45)_s]_s decreased by 55.38 %, 62.65 %, 46.41 %, and 31.71 %, respectively. The elastic modulus for [0]₁₆, [90]₁₆, [±45]_4s, and [(+45/0/0/–45)_s]_s increased by 90.93 %, 94.57 %, 49.22 %, and 8.22 %, respectively. [90]₁₆ sample has the minimum saturated moisture content and the maximum strength degeneration.     

Investigation on the interface damage in drilling low-stiffness CFRP/Ti stacks

Carbon fiber reinforced plastic and titanium alloy (CFRP/Ti) stacks have been widely used as aerospace structures because of their excellent combination of physical properties. Interface damage caused by interface gaps, significantly different from that of metal/metal stacks, is a common problem in the through-hole drilling of CFRP/Ti stacks with low stiffness. In this study, a force–deformation coupling model was developed to further examine the formation mechanism and the control method of interface damage. Firstly, the coupling model was built considering the interaction between the thrust force and the deformation. To solve this model, a numerical method was proposed in which specific cutting coefficients were calibrated using only the thrust force of rigid stacks. Secondly, drilling experiments were performed with different feed rates and bending stiffness. Experimental results indicate that interface damage mainly includes interlayer chips and surface damage of CFRP layers. The surface damage, which is irreparable, is caused by the rotary extension of metal chips along the interlayer gap. Thirdly, variations of the interface gap were calculated with the coupling model that had been verified by measured thrust forces. The damage area was found to have a linear dependence relation with the interlayer gap. However, in conditions of large gap sizes, the interface damage areas increased with the interlayer gap at high feed rates, while decreasing slightly at low feed rates. This phenomenon was satisfactorily explained by the presented model. Finally, a method was proposed to determine the appropriate pressure exceeding which no interlayer damage will occur. Additional drilling experiments proved the method effective. This study leads to further understanding of the forming mechanism of interlayer damage and of selecting appropriate parameters in drilling low-stiffness composite/metal stacks.     

钛合金零件钻削过程仿真与试验研究

钛合金被广泛用于航空工业中,譬如民用飞机吊挂滑轨等典型结构的制造。钛合金作为难加工材料,通常使用钻削的方法进行加工,不同的钻削参数对应不同的钻削温度和钻削力,而钻削温度和钻削力对加工精度影响较大。为使加工参数和加工精度得到很好地匹配,借助Deform 3D有限元仿真软件建立了钛合金热应力耦合有限元模型,通过软件仿真研究钛合金滑轨在加工过程中的钻削力以及钻削温度。首先,对钻头和钛合金试件进行网格划分。其次,建立材料本构模型和切屑分离标准,使用仿真软件得到加工过程的钻削力和钻削温度。最后,采用试验方法获取钻削温度和钻削力,与仿真结果进行对比。结果表明:仿真结果与试验较为吻合,仿真能输出有效的钻削力和钻削温度。     

Effect of cooling strategies on performance and mechanism of helical milling of CFRP/Ti-6Al-4V stacks

Hole-making for Carbon Fiber Reinforced Plastics(CFRP)/Ti-6Al-4V stacks is crucial for the assembling strength of aircraft structure parts. This work carried out experimental work for helical milling(HM) of the stacks with sustainable cooling/lubrication(dry, MQL and cryogenic)conditions. Cutting forces and temperatures at the CFRP layer, Ti-6Al-4V layer and the interface of stacks were obtained by a developed measuring system. The temperatures in CFRP machining at cryogenic condition varied fro...     

Cutting force model and damage formation mechanism in milling of 70wt% Si/Al composite

High-mass fraction silicon aluminium composite(Si/Al composite) has unique properties of high specific strength, low thermal expansion coefficient, excellent wear resistance and weldability. It has attracted many applications in terms of radar communication, aerospace and automobile industry. However, rapid tool wear resulted from high cutting force and hard abrasion, and damaged machined surfaces are the main problem in machining Si/Al composite. This work aims to reveal the mechanisms of milli...     

Defect suppression mechanism of ultrasonic vibration-assisted drilling carbon fiber/bismaleimide composite

Ultrasonic vibration-assisted drilling (UVAD) has recently been successfully applied in the drilling of carbon fiber reinforced polymer/plastic (CFRP) due to its high reliability. Multiple defects have been observed in the CFRP drilling process which negatively affects the quality of the hole. The carbon fiber/bismaleimide (BMI) composites is an advanced kind of CFRPs with greater strength and heat resistance, having been rapidly applied in lightweight and high temperature resistant structures in the aerospace field. To suppress the defect during the drilling of carbon fiber/BMI composites, it is necessary to comprehensively understand the defect formation and suppression mechanism at different positions. In this study, the defects formation in both conventional drilling (CD) and UVAD were observed and analyzed. The variation trend in the defect factor and thrust force with the spindle speed and feed rate were acquired. The results revealed that the UVAD could significantly enhance the hole’s quality with no delamination and burr. Meanwhile, the defect suppression mechanism and thrust force in UVAD were analyzed and verified, where the method of rod chip removal affected the exit defect formation. In summary, UVAD can be considered a promising and competitive technique for drilling carbon fiber/BMI composites.     

一种提高表面完整性的气膜孔成形方法

为了解决目前航空发动机涡轮叶片气膜孔成形工艺存在热影响严重等问题,提出了采用超快激光环切与螺旋扫描的加工方法,设计了一种可实现高效、无热效应气膜孔加工的双激光光源微加工系统,并从作用机理和实际加工过程两方面分析了热效应的产生原因,指出了其中的主要影响因素,然后针对这些因素选用DD6材料进行了工艺参数优化和实验验证.实验结果表明:采用500fs激光与微秒长脉冲激光复合加工的方式可以使精细钻孔的效率提升约10倍,并得到基本无重铸层和微裂纹的涡轮叶片气膜孔;其工艺参数包括扫描速度为2400r/min,重叠率为12%,进给量为5μm,重复频率为20kHz以及0.6Pa同轴吹气.表明超快激光配合合理的工艺参数和加工方式可以实现无热效应气膜孔加工,是一种有效提高气膜孔成形表面完整性的工艺方法.      

航空金属滤网的特种加工技术(英文)

Thanks to recent advances in manufacturing technology, aerospace system designers have many more options to fabricate high-quality, low-weight, high-capacity, cost-effective filters. Aside from traditional methods such as stamping, drilling and milling, many new approaches have been widely used in filter-manufacturing practices on account of their increased processing abilities. How- ever, the restrictions on costs, the need for studying under stricter conditions such as in aggressive fluids, the complicity in design, the workability of materials, and others have made it difficult to choose a satisfactory method from the newly developed processes, such as, photochemical machining （PCM）, photo electroforming （PEF） and laser beam machining （LBM） to produce small, inexpensive, lightweight aerospace filters. This article appraises the technical and economical viability of PCM, PEF, and LBM to help engineers choose the fittest approach to turn out aerospace filters.     

CFRP材料振动制孔研究进展

本文对碳纤维增强复合材料(CFRP)的特性进行了回顾,概述了目前纤维叠层材料孔加工缺陷和应对办法。简述了振动辅助加工(VAM)的特点,以及振动辅助钻削加工(VAD)对加工缺陷的抑制机理,最后总结了目前振动辅助钻削CFRP取得的进展。     

Enhanced ultrasonic total focusing imaging of CFRP corner with ray theory-based homogenization technique

Ultrasonic testing is effective in defect characterization and quality assurance of Carbon Fiber Reinforced Plastic (CFRP) components in the aerospace industry. Due to the coupling between complex shape and elastic anisotropy, the Phased Array Ultrasonic Testing (PAUT) and time-based Total Focusing Method (TFM) face significant challenges in the calculation of wave propagation. A wave velocity distribution model is established for a multidirectional convex corner of CFRP based on a homogenization theory and the above coupling effects are also incorporated. A ray-tracing method is proposed based on Dijkstra’s shortest path search algorithm. The predicted time of flight ensures that this technique, the homogenized TFM, could synthesize a high-quality focused image by post-processing on the full matrix capture data. Experiments on a laminate with three ?1.5 mm Side-Drilled Holes (SDHs) in different circumferential directions confirm a successful homogenized TFM imaging that all SDHs can be effectively detected. As compared to the isotropic scenario, the maximum positioning error is reduced to 0.12, 0.08, and 0.38 mm, and the Signal-to-Noise Ratios (SNRs) are increased by 2.1, 1.1, and 11.8 dB, respectively. It is suggested that the ray-tracing assisted TFM technique can effectively improve the imaging of corners in CFRP components.     

某型无人机碳纤维尾撑钻孔组合夹具设计与应用

结合设计图样及材料特性,研究了一种用于加工碳纤维尾撑的工艺及钻孔组合夹具,并阐述了其设计要点。