共查询到20条相似文献,搜索用时 62 毫秒
1.
实验研究了端壁孔式附面层抽吸对带间隙的高负荷直列叶栅流动特性和气动性能的影响,通过三种附面层抽吸方案与原型方案的对比分析,探讨了附面层抽吸抑制间隙流动、减小损失的机理。对叶片表面和下端壁进行了墨迹流动显示,并利用五孔探针对叶栅出口气动参数进行了测量,对比分析了叶栅流道内的流场特征和损失分布。结果表明,在间隙内布置抽吸孔能有效降低间隙流动动能,削弱间隙流与主流之间的相互掺混作用,减小因间隙流动引起的端壁区域流动分离,从而达到对三维流动分离的抑制,有效降低损失,且最大降幅达16.7%;间隙流动引起的流动分离和损失在流道中占主导地位,尽管在端壁沿周向合理布置抽吸孔能在一定程度上抑制近端壁的附面层或二次流发展,但这种局部效应仍不能显著改善叶栅的整体性能;端壁上不合理的抽吸控制策略反而可能影响主流的正常流动,导致损失增加,其中方案4损失增加了约3%。 相似文献
2.
3.
为研究高亚声速下附面层抽吸参数对流动分离控制的效果和机理,以高负荷扩压叶栅为研究对象,通过数值方法研究了抽吸布局和抽吸流量对叶栅内部流动分离控制效果的影响。结果表明,附面层抽吸能够显著改善叶栅内部流动,降低因附面层分离和端区角区分离、相互掺混造成的流动损失;高亚声速下附面层抽吸的最佳位置在附面层充分发展区域而非分离起始点附近;1.32%抽吸流量下,在叶片吸力面距离尾缘34%弦长处进行附面层抽吸的效果最佳,叶栅总损失降低54.03%;各抽吸槽因抽吸强度的降低使组合抽吸对于进一步改善流动效果并不明显;抽吸流量与抽吸效果呈正相关的关系,但是高亚声速下通过附面层抽吸无法完全消除高负荷叶栅内部角区分离。 相似文献
4.
以某高亚声速叶栅风洞为实验平台,运用粒子成像测速仪(PIV)对平面叶栅吸力面进行了附面层抽吸试验研究。验证了附面层抽吸技术在附面层分离流动控制方面的可行性和有效性。通过与数值模拟结果的对比分析,验证了本试验测量结果的可靠性。通过对不同抽吸位置处抽吸效果的研究表明:在同一抽气量下,合适的抽吸位置是控制附面层分离的重要因素。当抽吸位置处于分离起始点与严重分离区之间时,附面层分离才能够得到明显的抑制,流场结构得到显著的改善。 相似文献
5.
6.
为研究附面层抽吸对叶栅角区分离流动的控制效果和机理,以高负荷轴流压气机叶栅为研究对象,基于数值方法深入分析了不同抽吸方案对叶栅角区流场的影响以及叶栅攻角特性随抽吸流量组合的变化规律。结果表明:不同抽吸方案对叶片通道中的分离流动的控制机理不同,进而会影响叶片负荷及扩压能力;将吸力面抽吸与端壁附面层抽吸结合起来的组合抽吸方案基本消除了位于叶栅吸力面的附面层分离和角区分离,叶栅叶型损失系数显著降低,在5°攻角下,当吸力面抽吸量为1.88%,端壁抽吸量为0.82%时,损失系数相较于原叶栅降低约63.8%;并且进一步研究发现各抽吸槽的抽吸流量均存在其最佳临界值;在进行组合抽吸时,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对叶栅分离流动的控制。 相似文献
7.
8.
9.
在低速条件下,对不同吸气位置和吸气量的高负荷吸附压气机叶栅流场进行了实验研究,分析了吸气位置和吸气量对高负荷压气机叶栅流场的影响。结果表明,吸气位置和吸气量对高负荷吸气压气机叶栅流场影响显著,且在小吸气量下流场就有明显改善;附面层抽吸有效减小了积聚在吸力面角区的低能流体,流动分离被抑制,总损失下降明显,且抽吸对叶栅流场的影响随吸气量的增加而逐渐增大;在吸力面后部流动充分发展区域,采用附面层抽吸对抑制流动分离具有更好的效果。 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
14.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
15.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
16.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
17.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
18.
19.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows (Reφup to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the (non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity Vφ/Ωr with radial location to solid body rotation Vφ/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
20.
(高)超声速流动试验技术及研究进展 总被引:1,自引:1,他引:1
近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。 相似文献