金属间化合物Ho2Co17-xSix的磁性能机制研究

研究了非磁性原子Si替代Co对Ho2Co17金属间化合物结构和磁性的影响.X射线衍射表明,所有Ho2Co17-xSix(x=0.5,1.0,1.5,2.0,2.5,3.0)化合物都为Th2Ni17型六角结构;化合物的晶格常数和单胞体积都随Si含量的增加而呈线性下降.磁性测量表明,Ho2Co17-xSix化合物的居里温度和饱和磁化强度均随Si含量的增加而呈线性下降.从热磁曲线测量观察到,当0.5≤x≤3.0时Ho2Co17-xSix化合物出现由易面到易轴的自旋重取向,自旋重取向温度Tsr随Si原子含量的增加先下降,而后又上升,在x=2.5处出现最低点.     

FeCoVSiB非晶合金磁性能的研究

研究了Fe78Co5V2 Si6 B9非晶合金有效磁导率 μ′、损耗P随频率、磁场强度的变化 ;根据材料使用温度的不同 ,同时研究了在 0 .6 4A m磁场下 ,磁导率随温度的变化。研究表明 ,磁场强度一定时 ,Fe78Co5V2Si6 B9非晶合金的有效磁导率随频率增加而降低 ;频率一定时 ,有效磁导率随磁场强度的增加而增加 ;铁芯损耗均随频率、磁场强度的增加而增加 ;非晶态合金Fe78Co5V2 Si6 B9经不同温度、不同保温时间热处理后 ,磁导率随使用温度的变化 ,自室温始先略有增大 ,而后 ,随温度升高而降低     

碳化硅反射镜材料性能预测

预测了反应烧结SiC（RBSiC）的物理及部分力学性能与游离Si含量的变化关系，并对预测值与测量值进行比较以验证其符合程度。经预测，随Si含量的增加，RBSiC的密度呈线性下降，尤其是气孔对材料密度的影响非常明显;线膨胀系数和热导率均应呈加速上升趋势，比热容稍有下降；各模量均有下降趋势。随着气孔的增加，RBSiC的膨胀量变化不明显，比热容和热导率均呈减速下降趋势。RBSiC测量值与预测值产生偏差是因为材料中Si含量的增加导致缺陷增多以及计算性能用数据有偏差所致，但预测仍能较符合RBSiC性能随Si含量变化趋势，因此认为预测值较为合理可作为性能参考值使用。     

Thermoelectric Properties of Mg2Si1-xSnx Synthesized by Bulk Mechanical Alloying

Bulk mechanical alloying （BMA） has been successfully applied to solid-state synthesis of p-type and n-type thermoelectric materials Mg2Si1-xSnx （x = 0, 0.2, 0.4, 0.6, 0.8, 1） from element-powders at the room temperature in a relatively short time. The electrical conductivity, the Seebeck coefficient and the thermal conductivity of the Mg2Si1-xSnx are quite sensitive to the x-content. With the x-content rising, the electrical conductivity increases. When x = 0.6, it reaches the lowest and Mg2Si shows an n-type of semi-conducting However, when x = 0.2 and T 〉525 K, the Seebeck coefficient of the samples will change the opposite way. While x≥0.4, the samples present a p-type of semi-conducting. The figure of merit, Z of Mg2Si1-xSnx will be obtained in the range from 300 K to 700 K. When x = 0.6, Z proves to be higher than that of other samples at 300 K≤ T≤650 K.     

无压浸渗制备Si3N4／Al复合材料的界面反应研究

研究Si3N4多孔预制体的表面氧化程度对无压浸渗制备Si3N4/Al复合材料界面反应以及复合材料性能的影响是复合材料优化设计的基础.不同氧化程度的Si3N4多孔预制体在相同的浸渗工艺下无压浸渗制得Si3N4/Al复合材料,利用EDS,XRD和洛氏硬度计分别测定陶瓷多孔预制体的成份,复合材料的相组成和硬度.结果表明:Si3N4/Al复合材料组成相包括Al,Si3N4,AlN以及少量的Si,Mg2Si,MgO,MgAl2O4;随着氧化程度增加,复合材料内AlN相减少,MgO含量增加,并逐渐出现MgAl2O4相;复合材料的硬度随预制体的氧化程度增加而线性下降;预制体的氧化造成Si3N4和Al之间的反应减弱是硬度下降的重要原因.     

Ca对Mg-5Al-8Zn-xCa镁合金显微组织与力学性能的影响

采用重力铸造法制备了Mg-5Al-8Zn-x Ca(x=0,1.75,2.0,2.25,2.5,2.75,3.0,wt%)合金。使用XRD、OM和SEM等研究了Ca含量对合金组织与力学性能的影响。结果表明:铸态Mg-5Al-8Zn-x Ca合金主要由α-Mg基体、β-Mg17Al12相、Mg32(Al,Zn)49相及MgZn2相和Al2Ca相组成。当Ca含量从1.75wt%增加到2.75wt%时,基体晶粒显著细化,β-Mg17Al12相由粗大的连续网状转变为细小的断续网状分布于晶界上,层片状Al2Ca相也显著细化,此时合金的拉伸强度达到最大值138 MPa,较未加Ca时提高了27.8%;Ca含量继续增加至3.0wt%,晶粒又发生粗化,合金拉伸强度发生下降;拉伸断裂形式均为准解理脆性断裂。     

Thermoelectric Properties of Mg_2Si_(1-x)Sn_x Synthesized by Bulk Mechanical Alloying

Bulk mechanical alloying (BMA) has been successfully applied to solid-state synthesis of p-type and n-type thermoelectric mate-rials Mg2Si1–xSnx (x = 0, 0.2, 0.4, 0.6, 0.8, 1) from element-powders at the room temperature in a relatively short time. The electrical conductivity, the Seebeck coefficient and the thermal conductivity of the Mg2Si1–xSnx are quite sensitive to the x-content. With the x-content rising, the electrical conductivity increases. When x = 0.6, it reaches the lowest and Mg2Si shows an n-type of semi-conducting. However, when x = 0.2 and T >525 K, the Seebeck coefficient of the samples will change the opposite way. While x≥0.4, the samples present a p-type of semi-conducting. The figure of merit, Z of Mg2Si1–xSnx will be obtained in the range from 300 K to 700 K. When x = 0.6, Z proves to be higher than that of other samples at 300 K≤T≤650 K.     

热处理对Nb-10Si合金显微组织的影响

采用真空电弧熔炼法制备了 Nb-1 0 Si ( at% )合金 ,并在 1 85 0℃和 1 5 5 0℃温度氩气保护下进行了 2～ 1 0 0 h的热处理。综合通过 X射线衍射、透射电子显微术、扫描电子显微术及 X射线能谱对合金的显微组织进行了研究。结果表明 ,铸态 Nb-1 0 Si合金由连续的 Nb3 Si基体与均匀分布的 Nb相组成 ,1 85 0℃温度下热处理 2 h后 ,Nb晶粒明显长大 ;而在 1 5 5 0℃热处理后 ,Nb晶粒尺寸基本不变 ,Nb3 Si逐渐转变为 Nb和 Nb5Si3 相 ,且它们之间存在着一定的取向关系。1 5 5 0℃热处理 1 0 0 h后可以获得稳定的 Nb+ Nb5Si3 双相显微组织 ,是合适的热处理制度     

Si和Ti对Nb-6Hf-4Zr-2B合金组织和室温力学性能的影响

 为了寻求Nb合金的强度和塑性的平衡,设计了以Nb基固溶体Nbss为主导相的Nb-xSi-6Hf-4Zr-2B-yTi(x=4,8;y=10,30;原子分数)合金,研究了Si和Ti对合金组织和室温力学性能的影响。结果表明,合金由Nbss、Nb3Si和Nb5Si3等3相组成。4Si-(10,30)Ti合金铸态组织是Nb枝晶和分布在枝晶间的硅化物(Nb3Si和Nb5Si3),8Si-(10,30)Ti合金Nb枝晶间分布的是Nb/硅化物(Nb5Si3)的共晶和Nb3Si,随着Si和Ti含量的增加,硅化物体积分数增加。1 600 ℃退火50 h可使部分Nb3Si共析分解,改变合金的组织形貌和各相的体积分数。随着Si和Ti含量的增加,合金的硬度和强度增加,但塑性和韧性降低。Nb枝晶的失效方式为解理断裂,而硅化物为脆性断裂。     

激光熔覆制备WCp/Ni-Si-Ti复合涂层

在Ni基高温合金表面预置3种不同WC含量的Ni78Si13Ti9(at%)粉末,采用激光熔覆制备了WC和原位自生TiC复相陶瓷增强Ni3(Si,Ti)基复合涂层.利用扫描电镜、能谱分析仪和X射线衍射仪对熔覆层组织进行分析,并测量了其显微硬度.结果表明,熔覆层与基体呈冶金结合,熔覆层组织主要由Ni(Si)固溶体、Ni3(Si,Ti)金属间化合物和WC-TiC复相陶瓷组成.随WC添加量增加,涂层中复相陶瓷含量增多;孔隙率增大;碳化物形态演变历程为不规则状、花瓣状以及不规则状和花瓣状共存.     

The Influence of Co Addition on Phase Transformation Behavior and Mechanical Properties of TiNi Alloys

The influences of Co-addition on phase transformation behavior and mechanical properties of TiNi alloys were investigated. Re- sults indicate that, as a substitute for Ni, Co added to TiNi alloys can dramatically decrease the martensite transformation temperature, and R phase transformation and martensite transformation are accordingly separated. When Co-content reach 10 at.%, the martensite transformation temperature is lower than that of liquid nitrogen. During deformation at room temperature, Ti50Ni48Co2 alloy exhibits good ductility with a lower stress plateau caused by stress-induced martensite and martensite reorientation.     

碳纤维表面CVD硅涂层对其性能的影响

 分析了碳纤维表面化学气相沉积Ｓｉ涂层的相结构,研究了Ｓｉ涂层对碳纤维抗氧化性能及强度的影响。结果表明：涂层中Ｓｉ元素呈非晶态分布；Ｓｉ涂层可提高碳纤维的抗氧化性能；氧化温度不同,Ｓｉ涂层碳纤维的氧化失重或增重规律也不相同。同时,Ｓｉ涂层降低了碳纤维拉伸强度,而适度空气氧化又可使Ｓｉ涂层碳纤维强度得到大幅度提高；Ｓｉ涂层碳纤维的强度随氧化温度、氧化时间的变化而改变。     

Microstructure, Mechanical Properties and Oxidation Resistance of Nb-22Ti-14Si-2Hf-2Al-xCr Alloys

Nb-22Ti-14Si-2Hf-2Al-xCr (x=2, 6, 10, 14, 17 at%) alloys are prepared by arc-melting under argon atmosphere. Microstructural characteristics, mechanical properties and oxidation resistance of the arc-melted alloys are investigated. At 2 at% Cr content, the microstructure is composed of Nbss, Nb3Si and a small quantity of Nb5Si3, when the Cr contents increase, Nb3Si disappears. For the high Cr content (x ≥ 10 at%) alloys, besides the Nbss and Nb5Si3, Cr2Nb is also detected. With the increase of Cr content, the volume fractions of Cr2Nb and Nb5Si3 increase, while that of Nbss increases firstly and then begins to degrade when the Cr content is higher than 6 at%. For the alloy with 2 at% Cr, the room temperature fracture toughness is about 14.5 MPa·m1/2, but badly decreases to about 8.5 MPa·m1/2, when the Cr contents increase. Vickers hardness of Nbss tends to increase linearly from about 400 to 500, while that of silicides is not sensitive to Cr contents, about 950. The appearance of Cr2Nb phase significantly improves the high temperature oxidation resistance of the alloys with high Cr contents. The isothermal oxidation tests show that the oxidation kinetics of the alloys with various Cr contents follows parabolic oxidation kinetics.     

热处理制度对1Cr16CO5Ni2Mo1WVNbN钢组织和性能的影响

通过试验研究了不同热处理制度对1Cr16CO5Ni2Mo1WVNbN钢的金相组织、室温拉伸、冲击性能的影响。得出结论：随淬火温度升高,回火温度降低,合金的室温冲击韧性降低,而室温拉伸强度略有升高;淬火介质对室温力学性能以及金相显微组织的影响不明显;淬火保温时间和回火保温时间对合金的室温冲击韧性和室温拉伸性能影响不大。因此合金的最佳热处理工艺参数为：1100oC×90min,油冷＋680℃×3h,空冷。     

Improving tensile-shear properties of friction stir lap welded dissimilar Al/Mg joints by eliminating hook defect and controlling interfacial reaction

To improve tensile-shear properties of fiction stir lap welded(FSLW) dissimilar Al/Mg joints, pin-tip profiles were innovatively designed and welding speed was optimized, and effects of them on formation, interface microstructure and mechanical properties of different FSLW joints were investigated. With increasing the welding speed, the tensile-shear load of FSLW joints produced by three pins presents an increasing firstly and then decreasing trend. Compared with Rpin, the hook and hole defect i...     

Co/NM/FM(NiFe and Co)纳米多层膜的层间耦合效应

巨磁电阻自旋阀多层膜作为磁敏传感器材料与磁随机存储器(MRAM)材料，具有高的可靠性与灵敏度，在航空航天等高科技领域有着极大的应用前景。研究多层膜各层间的耦合效应与各层厚度、磁学性能之间的内在关系，对提高自旋阀的巨磁电阻效应、磁灵敏性等具有重要的作用。本研究采用磁控溅射沉积制备了(Cu／Co、Cu／NiFe，Ta／NiFe双层膜与Co／Cu／Co、Co／Cu／NiFe、Co／Ta／NiFe)三明治结构薄膜。采用振动样品磁强计对薄膜磁性、四探针法对薄膜磁阻性能进行了测试研究，采用洛仑兹电子显微镜法观察了薄膜的磁畴结构。研究结果表明，层间耦合效应不仅与非磁性中间层的厚度相关，而且与中间层材料的特性相关。磁阻与磁畴观察均表明层间耦合效应随中间层厚度的增加而减小，而Cu作为中间层的多层膜的层间耦合大于Ta作为中间层的层间耦合。     

核磁共振陀螺仪中共振磁场强度优化研究

核磁共振陀螺中,共振磁场的幅值直接影响原子核自旋磁矩进动信号的强度,进而影响陀螺信号的信噪比。基于核磁共振陀螺Bloch方程,从理论和实验两方面研究了共振磁场幅值对宏观原子核自旋磁矩的影响。结果表明,随着共振磁场幅值的增加,宏观核自旋磁矩进动信号的强度先增大后减小,进动信号的强度与共振磁场的幅值呈色散关系。共振磁场幅度值存在最优值,且最优值的取值与惰性气体原子的旋磁比、纵向弛豫时间和横向弛豫时间有关。