基于数值计算的机载SAR空变运动补偿算法

针对机载合成孔径雷达(SAR)高分辨率宽测绘带(HRWS)成像问题,在分析结合两步运动误差补偿的距离徙动算法基础上,提出一种基于数值计算的空变运动误差补偿算法。通过对粗聚焦图像进行分块,在子块的两维波数域进行空变运动补偿,补偿的相位包括方位相位误差、距离相位误差以及方位和距离的耦合相位,因此该算法在复杂航迹、高分辨和宽测绘带情况下仍具有较好的鲁棒性。最后对SAR仿真数据和实测数据进行处理,并与结合两步运动误差补偿的距离徙动算法进行比较,处理结果表明该算法能够更好地补偿空变运动误差。     

基于脉组间频率步进的合成超宽带距离像及速度分析

 对脉组间频率步进信号进行信号处理可直接获得合成超宽带(UWB)距离像及目标速度信息,但由于多普勒色散引入的快速傅里叶变换(FFT)输出失配误差和距离多普勒耦合,导致距离像的失真。介绍消除多普勒色散的影响的方法,分析且补偿距离多普勒耦合对距离像的影响,进一步讨论由测速误差产生的补偿量化误差对距离像的影响,并推导由此导致的距离走动公式。提出的迭代二分逼近法使速度分辨提高 N 倍( N 为脉组个数),从而得到目标真实高分辨距离像。仿真实验结果表明多普勒色散得到消除且 N 的选取更加灵活。     

基于压缩感知的MIMO-SAR运动误差补偿与成像

多发多收合成孔径雷达（MIMO-SAR）利用多通道空间并行采样的优势可实现高分辨成像,但不可避免地存在运动误差与海量数据不便于存储与传输的问题。针对该问题提出一种基于压缩感知的MIMO-SAR运动误差补偿与成像方法。首先通过详细分析MIMO-SAR运动误差回波信号模型,在全采样条件下利用两步运动补偿技术实现对回波数据的运动误差补偿处理,其次针对降采样回波数据的运动误差补偿,通过构造变换算子与压缩感知（CS）重构模型的方法实现第1步运动误差补偿、距离脉压以及距离徙动校正处理,然后再进行第2步误差补偿与方位向脉压处理获得成像结果。最后通过仿真实验验证了所提方法能够在大幅压缩回波数据的情况下,实现MIMO-SAR运动误差补偿与成像处理。     

Range-Doppler Imaging of Rotating Objects

During the integration time required to obtain fine Dopplerfrequency resolution in a range-Doppler imaging radar, a point on a rotating object may move through several range and Doppler resolution cells and produce a smeared image. This motion can be compensated by storing the appropriately processed return pulse, and the angular coordinates are determined by the angular coordinates of the radar antenna. The resulting stored data represents the three-dimensional Fourier transform of the object reflectivity density, and hence can be processed by an inverse Fourier transformation. Also included is an analysis of the three-dimensional radar/object geometry with separate source and receiver locations. The effects of various system aberrations are investigated and experimental results from a microwave test range which demonstrate the image improvement are presented.     

A new algorithm for the formation of ISAR images

A new technique for implementing the enhanced image processing (EIP) algorithm for the formation of inverse synthetic aperture radar (ISAR) images is presented. The EIP algorithm is required when, during the formation of an image, scattering centers on a target move out of range and/or Doppler resolution cells. This phenomenon is common for high resolution imagery of practical-sized targets. The method presented is based entirely on the fast Fourier transform (FFT) and therefore does not require the interpolation schemes that are prevalent in the standard EIP implementation. A brief review of the theory of radar imaging is presented to establish the notation for the work. Following the presentation of the new algorithm, a simple example is given to demonstrate the effectiveness of the new technique. In addition work is presented that demonstrates the processing required to reduce the sidelobes in imagery generated by the EIP technique     

基于虚拟慢时间的双基地ISAR成像算法

针对双基地角时变引起的逆合孔径雷达（ISAR）图像畸变和散焦问题，提出了一种基于虚拟慢时间的成像算法。首先，分析了双基地角时变对ISAR成像的影响机理。然后，基于图像对比度最大准则估计等效旋转中心位置，完成初次相位补偿。最后，通过虚拟慢时间构建基于非均匀虚拟采样的补偿系数矩阵，并通过方位向非均匀傅里叶变换得到目标的ISAR像。算法基于图像对比度最大准则解决等效旋转中心位置估计问题，通过虚拟慢时间消除转动相位项的高次项影响，利用非均匀傅里叶变换解决随机虚拟采样的谱估计问题。理论分析和仿真结果验证了算法的有效性和鲁棒性。     

Identifying the number of aircraft in formation flight using ISAR technique

Ｄｅｖｅｌｏｐｍｅｎｔｏｆｉｎｖｅｒｓｅｓｙｎｔｈｅｔｉｃａｐｅｒｔｕｒｅｒａｄａｒ（ＩＳＡＲ）,ｗｈｉｃｈｐｏｓｓｅｓｓｅｓｈｉｇｈｃｒｏｓｓ－ｒａｎｇｅｒｅｓｏｌｕｔｉｏｎｃａｐａｂｉｌｉｔｉｅｓ,ｍａｄｅｉｔｐｏｓｓｉｂｌｅｔｏｒｅｓｏｌｖｅｔ...     

Joint time-frequency transform for radar range-Doppler imaging

Conventional radar imaging uses the Fourier transform to retrieve Doppler information. However, due to the complex motion of a target, the Doppler frequency shifts are actually time-varying. By using the Fourier transform, the Doppler spectrum becomes smeared and the image is blurred. Without resorting to sophisticated motion compensation algorithms, the image blurring problem can be resolved with the joint time-frequency transform. High-resolution time-frequency transforms are investigated, and examples of applications to radar imaging of single and multiple targets with complex motion are given     

方位维逆合成孔径雷达(ISAR)运动补偿成象中的预加处理

在方位维逆合成孔径雷达（ISAR）运动补偿成象中,为了获得方位维的高分辨力,需要处理的数据量很大。预加处理首先对原始数据进行频移和滤波,然后由滤波后的数据进行抽取,从而大大压缩了所需处理的数据,减小了运动补偿和成象的计算量,提高了成象处理速度。电磁仿真数据和外场实测数据的处理结果验证了预加处理的有效性。     

A SAR processor based on two-dimensional FFT codes

A synthetic aperture radar (SAR) processor approach based on two-dimensional fast Fourier transform (FFT) codes coupled with an asymptotic evaluation of the unit response function is presented. For the latter, no approximation is made to the distance function, so that the full range of geometric aberrations is analytically considered, enabling an effective reference filter to be designed. The two-dimensional FFTs were designed as to run on computers of very limited memory: the required FFT is computed by means of FFTs of lower order. Two FFT codes were considered: one is faster and allows full or reduced (quick look or multilook) resolution performance to be obtained easily; the second is slower but allows the use of a space-varying filter and/or investigations on limited portions (zoom) of the image. Both codes are suited to parallel processing, e.g. by a transputer net. A full discussion on computer memory and time requirements is presented as well as first examples of image processing results     

Target-Motion-Induced Radar Imaging

Imaging from ground-based (stationary) radars of moving targets is often possible by utilizing a "synthetic aperture" developed from the target motion itself. The theory and experimental results associated with such processing are addressed. An aircraft is imaged from both a straight flight and a turn with recognizable results. Analysis shows that two-phase components exist in the radar return, one being gross velocity induced, the other being interscatterer interference within the target itself. The former phase must be removed prior to imaging and techniques are developed for this task. Preprocessing, range curvature, range alignment, motion compensation, and presumming are all addressed prior to presenting the experimental results. Coherence processing intervals, range collapsing, and range realignment are all examined during the processing aspects of the paper.     

基于距离子带的机载SAR高精度多级空变运动补偿

运动补偿（MOCO）是机载合成孔径雷达（SAR）获取高质量图像的关键,超高分辨率成像中,如何精确、高效地校正空变运动误差仍是很大的挑战。本文提出了一种改进的多级空变运动补偿方案,兼顾处理的精度和效率。首先,采用一步运动补偿法有效去除运动误差的距离空变分量,避免引起额外的距离徙动校正（RCMC）误差。同时,修正视线方向误差的传统计算方式,保证相位精度的前提下结合距离子带实现无插值的近似距离包络补偿。然后,利用距离子带降低残余方位空变误差的距离空变性和对方位时频关系的影响,显著改善宽波束情况下的聚焦效果,降低孔径依赖补偿算法的运算量。最终分辨率达到0.1 m,具有实际工程应用价值。点目标仿真和实测数据处理验证了所做的研究。     

结合视线方向运动补偿的滑动聚束SAR子孔径成像算法

滑动聚束合成孔径雷达(SAR)是一种新兴的成像模式,既可以提高方位向分辨率又能够扩展成像范围。其数据处理时需要考虑两个关键问题:一是系统脉冲重复频率(PRF)不足,方位向信号发生混叠;二是合成孔径长度的增加使运动误差的影响更为突出,运动补偿(MOCO)精度要求提高。基于子孔径技术,提出了一种改进的高分辨率成像算法。划分子孔径克服了PRF不足的问题;子孔径数据处理采用结合视线(LOS)方向运动补偿的Omega-K算法,实现更高精度的运动补偿,提高了聚焦质量。最终的方位向分辨率达到0.1 m,具有实际工程应用价值。点目标仿真和实测数据处理验证了算法的有效性。     

基于修正离散Chirp-Fourier变换的高速目标ISAR距离像补偿

分析了高速运动目标的逆合成孔径雷达（ISAR）回波信号模型和高速运动对ISAR信号处理的影响。结果表明,高速运动特征会导致目标一维距离像的畸变和二维像的模糊。为此,提出了一种基于修正离散Chirp Fourier变换（MDCFT）的高速运动目标距离像补偿算法,采用MDCFT谱包络最小Shannon熵准则进行参数估计,可解决幅度最大准则下参数估计性能恶化的问题。仿真结果表明了该距离像补偿算法的有效性。     

基于液晶光阀的动态红外场景仿真研究

介绍了基于液晶光阀的动态红外场景仿真系统构成,分析了液晶光阀的波长变换和空间调制机理。对反映红外场景仿真效果主要因素(光谱输出特性、时间响应特性和空间分辨力)进行了理论分析和研究。利用优化设计液晶光阀参数构建的动态红外场景仿真样机,测量其光谱输出特性、时间响应特性和空间分辨力,结果表明,仿真系统的输出光谱可覆盖中波和长波红外波段,可实现帧频70Hz,系统空间分辨力优于10 lp/mm(受红外光学系统和红外热像仪分辨力限制)。     

Simultaneous ISAR imaging of group targets flying in formation

This paper proposes a novel inverse synthetic aperture radar(ISAR) imaging method based on second-order keystone transform(KT) and Sandglass transform for group targets flying in a formation with constant accelerated rectilinear motion in the same radar beam. First, range curvature and range walk of each sub-target among group targets are corrected by the second-order KT combined with the quadratic phase term compensation. After range alignment, the signals in each range frequency cell can be modelled as multiple chirp signals and then the Sandglass transform is utilized to cross-range imaging, which transforms the time–frequency distribution of the signals in each range frequency cell into beelines parallel to the slow time axis simultaneously. Finally, cross-range profiles of group targets in each range frequency cell are obtained via a projection of the perk of every scatterer in the two-dimensional accumulation plane onto the frequency axis. The advantage of the proposed method is that it can align range profiles of each sub-target simultaneously and image cross-range profiles directly without separating the returned signals, which simplifies the operation procedure. Simulation results are used to demonstrate the effectiveness of the proposed method.     

Super resolution time delay estimation via MODE-WRELAX

We consider estimating time delays and amplitudes (real- or complex-valued) from the superposition of very closely spaced signals with known shapes. The well-known high resolution MODE (Method Of Direction Estimation) algorithm, which was originally proposed for angle estimation in array processing, is modified and used with our efficient time delay estimation method WRELAX (Weighted Fourier transform and RELAXation based) algorithm to deal with this problem. The proposed method is referred to as MODE-WRELAX. MODE-WRELAX provides better accuracy than MODE and higher resolution than WRELAX. Moreover, it can be used for both complex- and real-valued signals (including those with highly oscillatory correlation functions). Numerical results show that the MODE-WRELAX estimates can approach the corresponding Cramer-Rao bound. Efficient implementation of the algorithm is also discussed     

Computer Simulation of Synthetic Aperture Radar Images of Three-Dimensional Objects

A digital simulation of coherent synthetic aperture radar (SAR) images of three-dimensional objects is described. The simulation is intended to produce representative SAR images that would be suitable for image analysis and pattern recognition studies. The procedure involves a modeling of the object using a combination of three-dimensional quadratic shapes yielding a smooth surface representation. The radar images of these models are then computed using physical optics scattering theory. Finite resolution both in range and cross-range direction is incorporated via a theoretical analysis which results in a simple Fourier transform representation of an equivalent "offset" window filter. Examples of the computer simulation for both infinite resolution and blurred or finite resolution are given for a KC-135 aircraft model.     

双基地角时变下的ISAR等效旋转中心估计

双基地逆合成孔径雷达（ISAR）距离-多普勒算法成像时，容易引起越分辨单元徙动问题，影响成像质量，为了抑制越分辨单元徙动，需要估计目标的等效旋转中心。本文针对双基地角时变下的ISAR等效旋转中心估计问题，提出了一种等效旋转中心估计算法。该算法首先将运动补偿后的一维距离像序列分为两组并分别成像，得到两幅图像；其次，假定某个距离单元为等效旋转中心位置，对两幅图像进行畸变校正，使得两幅图像只存在一个视角差，按视角差旋转其中的一幅图像，并与另一幅图像作相关，得到相关系数；然后，假定下一个距离单元为等效旋转中心位置，重复上述步骤，直至遍历结束，相关系数最大值对应的假定位置就是估计的等效旋转中心。最后进行了仿真对比实验，表明本文算法能够有效估计双基地角时变下的ISAR等效旋转中心位置。     

基于时间反转和降阶Keystone的SAR-GMTI快速聚焦方法

对合成孔径雷达（SAR）地面运动目标聚焦技术进行了研究。针对现有运动目标聚焦方法存在的问题,提出了一种基于时间反转和降阶Keystone的SAR地面运动目标检测（SAR-GMTI）快速聚焦方法。首先,根据目标的机动特性建立了3阶距离模型;其次,针对目标多普勒中心模糊引起的多普勒谱分裂现象,结合所提时间反转处理（TRP）和降阶Keystone变换处理估计出运动目标2阶参数。此后,构造2阶相位补偿函数补偿运动目标的2阶距离徙动和多普勒徙动,从而完成运动目标的聚焦。同时,所提方法没有任何参数搜索过程,降低了计算复杂度。最后,仿真实验验证了所提算法的正确性和有效性。