共查询到20条相似文献,搜索用时 859 毫秒
1.
多用途战斗机/涡扇发动机一体化循环参数优化 总被引:6,自引:0,他引:6
针对多用途战斗机的特点,发展了基于飞/发一体化的涡扇发动机循环参数优化设计模型和相应的计算程序,优化设计模型中包括双变量控制涡扇发动机特性计算模型、进排气系统安装特性计算模型、飞机气动特性分析模型、重量组成分析模型、任务剖面分析模型、约束分析与任务分析模型和优化计算模型等。重点研究了多用途战斗机约束边界的获得方法,利用多岛遗传算法和自适应模拟退火优化算法,分别对现役多用途战斗机、不加力超声速巡航多用途战斗机以及下一代先进多用途战斗机用涡扇发动机循环参数进行了优化计算,对计算结果进行了分析,获得了对多用途战斗机用涡扇发动机循环参数选择有指导意义的结论。 相似文献
2.
本文对有和没有超音速巡航任务段的第四代战斗机推进系统的循环参数进行了最优化计算,分析了超音速巡航距离、发动机全寿命费用和部件效率对发动机最优循环参数选取的影响。结果表明宜采用小涵道比涡扇发动机,而且不考虑费用时涡轮前温度取值越高越好,考虑费用时则有最大值;提高发动机部件效率对循环参数取值影响较大,而且使飞机性能提高较多。 相似文献
3.
4.
核心机派生涡扇发动机部件及整机匹配 总被引:1,自引:0,他引:1
以核心机与低压系统的部件及整机气动热力匹配关系为理论依据,在全面考虑低压压缩系统与核心机压气机的匹配约束关系、核心机涡轮工作状态相应变化以及派生发动机内外涵整机匹配的多因素下,建立了核心机派生涡扇发动机部件及整机气动热力循环匹配算法模型.应用该模型,进行了核心机派生涡扇发动机循环参数及性能趋势分析,计算结果表明高低压和整机匹配约束直接影响核心机派生涡扇发动机循环参数和整机性能,为核心机派生系列化涡扇发动机工程实践应用中所涉及的部件/整机参数匹配及性能预估提供分析和设计参考. 相似文献
5.
6.
针对单参数驱动的涡扇发动机性能退化预测精度不高的问题,提出了一种基于气路参数融合的涡扇发动机性能退化预测的方法。通过监测发动机性能退化过程中多源参数,采用专家经验和核主成分分析相结合的方法,进行发动机性能参数的选择和融合,从而构建健康参数。基于非线性Wiener过程构建涡扇发动机退化模型,采用极大似然方法求得发动机退化模型的离线参数估计值;由于不同发动机性能退化的差异性,基于贝叶斯更新理念对随机参数进行实时更新,可以实现对单台发动机的性能退化实时预测。通过实例验证,采用此方法在预测末端方均根误差为0.028 3,整体预测精度提升了54.5%,可以辅助指导维修决策。 相似文献
7.
升力风扇和涡扇发动机组合动力系统性能模拟与分析 总被引:3,自引:2,他引:1
基于部件匹配和多设计点分析技术,发展了加装升力风扇的涡扇发动机性能计算模型.以F135涡扇发动机为例,对模型的可靠性进行了验证.数值模拟结果表明:升力风扇不工作时,涡扇发动机性能模拟与常规涡扇发动机是一致的,当升力风扇工作时,若实现低压涡轮与涡扇发动机风扇、升力风扇工作点的匹配,不仅需要调节尾喷管喉道面积,而且可变外涵道出口面积、低压涡轮导向器喉部面积也需要调节.基于该模型,可以进行带升力风扇的涡扇发动机循环参数匹配和不同任务状态的性能分析. 相似文献
8.
大涵道比间冷回热涡扇发动机总体方案研究 总被引:1,自引:1,他引:0
《燃气涡轮试验与研究》2016,(1):1-9
在分析间冷回热涡扇发动机工作机理的基础上,进行了大涵道比间冷回热涡扇发动机循环参数分析。以波音767-200ER量级飞机为装机对象,开展了间冷回热发动机方案研究。对比分析了间冷回热涡扇发动机与多种类型涡扇发动机的总体性能方案,并从发动机总体性能及特性的角度,比较分析了大涵道比涡扇发动机引入间冷回热技术所带来的收益。最后,提出了研制间冷回热涡扇发动机需突破的主要关键技术。 相似文献
9.
在涡轮基组合动力系统的使用场景中,高速涡轮发动机为了实现起飞、跨声速、模态转换等状态下的性能指标,需要扩
展使用速域范围,兼顾多状态推力性能,对于发动机构型和循环参数选取提出了特殊的要求。开展基于循环参数分析的高速涡轮
发动机构型方案设计,通过分析高速涡轮发动机在不同速域下的使用需求,明确发动机的技术特征,并从性能、结构、技术发展趋
势等多角度对高速涡轮发动机构型进行分析,针对双转子涡扇构型的高速涡轮发动机开展循环参数分析,明确压比、涵道比和涡
轮前温度对发动机不同工况性能的影响。结果表明:变循环是高速涡轮发动机的理想构型方案。现阶段应基于双转子涡扇构型
逐步集成变循环特征部件,并通过合理的循环参数匹配,实现高低速性能的兼顾。 相似文献
10.
为了研究主燃烧室采用增压燃烧(PGC)的涡扇发动机性能,建立了其热力循环过程计算模型,采用考虑增压特性的传
统涡扇发动机性能计算方法,分析了增压比、涡轮前温度、涵道比、飞行速度、飞行高度等循环参数对增压燃烧涡扇发动机的性能
影响,并与传统涡扇发动机的性能进行了对比评估。结果表明:增压燃烧发动机循环效率高于等压燃烧发动机的,且加热比越大,
增压燃烧发动机性能优势越明显。初步获得了不同循环参数对增压燃烧涡扇发动机的性能影响规律。与同参数的传统涡扇发动
机相比,在总增压比为25~45、涡轮前温度为1500~1800 K内,增压燃烧涡扇发动机的单位推力增大4.7%~8.6%,耗油率降低4.6%~
8.5%;在飞行高度为15 km、马赫数为0~3内,增压燃烧涡扇发动机的推力增大4.1%~27.6%,耗油率降低2.3%~11.4%,并且飞行马
赫数越高,增压燃烧涡扇发动机的性能优势越大。 相似文献
11.
12.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
15.
16.
17.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
18.
FU Hong-jun MA Chong-qi KUANG Nai-hang LUAN Shi-lin 《中国航空学报》2007,20(2):124-128
This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered. 相似文献
19.
Xu Chenghai Meng Songhe Zhang Mingfu Zuo Hongbo Wang Guigen 《中国航空学报》2007,20(5):475-480
本文利用有限元法对冷心放肩微量提拉法(SAPMAC)生长大尺寸蓝宝石单晶过程中的热应力进行了模拟计算,应用临界缺陷理论解释了裂纹的萌生与扩展机理。研究表明,晶体内的热应力主要与晶体生长速率,环境温度和结晶取向有关;较大热应力多出现在结晶界面,放肩、收尾以及直径急剧变化等位置;最大热应力总是出现在籽晶与新生晶体的界面附近。裂纹将在临界缺陷位置产生,并在应力作用下沿a或m面扩展。计算结果与实验结果基本吻合,通过晶体生长系统和生长工艺的改进,对晶体的开裂问题得到了有效的抑制。 相似文献
20.
CHENG Wen-yuan CHANG Yan CUI De-gang XIE Xiang-hui 《中国航空学报》2007,20(1):55-59
To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm (PPGA) is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis (FEA) software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources. 相似文献