首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 93 毫秒
1.
磁航向传感器作为机载设备,它的工作情况与载体环境的影响有着密切的关系,测得的磁航向角存在着较大的误差,不能直接用来进行导航定位。所以,必须对其进行误差补偿,提高磁航向角的测量精度,才能用于导航定位。罗差是磁阻罗盘的主要误差源,文中介绍了罗差方程式,并重点推导了基于最小二乘法的七参数八位置误差标定方法。基于该方法的磁航向补偿算法的性能试验结果证明,磁航向误差基本维持在0.5°左右,满足了精度的要求。  相似文献   

2.
解决强磁环境下磁强计易受干扰的问题,能够提高微型姿态参照系统航向角测量精度。建立了磁强计误差两次补偿模型,首先采用椭圆坐标修正法对磁强计进行罗差补偿,以减小环境磁场的干扰;其次采用最小二乘拟合法对获得的磁航向角进行二次补偿,提高系统航向角测量精度。试验结果显示:系统航向角测量值的误差均方值由补偿前的3.982°降为补偿后的0.386°,精度提高近10.3倍,表明该补偿方法能够有效降低磁场环境的干扰,提高系统航向角测量精度。  相似文献   

3.
现有的磁航向测量系统体积、重量、功耗偏大,并且调试、误差补偿算法复杂、整体费用偏高,针对这些问题,设计了一个在小角度俯仰、滚转情况下的小型磁航向测量系统.该系统采用带DSP指令的32位高速处理芯片AVR32 UC3B0256、新型倾角传感器SCA100T以及磁阻传感器HMC 1022构成数字化解算平台,实现了误差补偿.实验数据显示,在水平状态下,磁航向测量值最大误差为±1.4;当俯仰角低于30°或滚转角低于35°时,随着角度的增加,磁航向输出误差变化不大,最大误差分别为3.7°和2.8°;当俯仰角超过30°或滚转角超过35°时,磁航向输出误差会急速增大.结果表明,该系统在小角度俯仰、滚转情况下具有较准确的磁航向角解算能力.  相似文献   

4.
微型无人机磁航向测量系统的设计与实现   总被引:1,自引:0,他引:1  
基于地磁测量原理的磁阻传感器具有体积小、启动快、功耗低等优点,以磁阻传感器为核心设计并实现了一种低成本微型无人机磁航向测量系统,介绍了磁阻传感器的工作原理,给出了航向角的计算方法,对硬件电路和软件设计进行分析研究。转台实验表明,基于磁阻传感器的微型无人机磁航向测量系统达到了设计要求。  相似文献   

5.
针对无卫星信号环境中单兵人员导航定位需求,设计了一种基于自包含传感器的单兵导航系统,重点研究了惯性传感器和压力传感器组合的零速区间检测算法,并通过对单兵导航系统背景磁场误差进行补偿来计算航向角,实现了速度观测量和航向观测量的准确提取。在此基础上,采用Kalman滤波器对系统状态误差进行估计,并对惯性导航解算结果中的累积误差进行修正。最后,在实际路线上开展了单兵导航系统定位实验,实验结果表明,行人在矩形路线终点位置处的位置误差为0.42m,占行走总路程的0.33%,从而证明了零速修正和航向修正能有效提高单兵导航系统的定位精度。  相似文献   

6.
栽体磁场的干扰是导致地磁导航精度较低的主要因素,在对无人机载体磁场干扰地磁场产生的地磁测量误差简要分析的基础上,将小姿态时地磁匹配导航采用的12系数误差补偿模型引入一种无人机地磁定向导航的罗差修正.在静态条件下,利用无磁转台分别获取无人机在±30°姿态角范围内有无干扰源的磁测数据.实验数据分析表明,通过补偿,栽体航向角在±5°范围内其误差均方差由2.174°下降到0.350°,其余角度下航向角误差均方差则由2.282°下降到0.732°,满足无人机在大角度姿态飞行时航向稳定度优于±3°的要求.  相似文献   

7.
在飞行状态下,姿态航向参考系统的航向由磁航姿计算机的姿态和磁罗盘的磁通量算得,由于磁罗盘和航姿计算机在机上有安装误差,使得算出的航向有一定偏差,针对这一问题,文章提出了一种补偿机上磁罗盘安装误差的方法。机上试验表明:该方法补偿了磁罗盘在机上的安装误差,可有效提高磁航向的精度。  相似文献   

8.
无人机航向测量的罗差修正研究   总被引:20,自引:2,他引:18  
 针对数字式磁航向测量系统在无人机上的应用,系统地研究了任意姿态下的罗差修正问题。通过分析罗差形成的原因,提出一种更为简单的罗差修正方法和确定罗差系数的工程方法。为了减少试验工作量和试验数据的错误,用计算机检验罗差系数的正确性,并提出试验数据正确性的检验方法。实验结果表明,该方法是很有效的。这种方法不仅可用于无人机,也可用于车辆、轮船等其它运载工具。  相似文献   

9.
磁力计在行人自主导航系统中用于提供绝对航行信息,而航向的精度直接决定着系统定位的精度。针对目前磁力计标定方法中存在磁干扰等问题,提出了一种基于最小二乘法和"8"字校准法对磁力计零偏进行实时校准的方法。该方法先利用最小二乘法修正磁力计零偏,再根据磁力计的模值大小及方差作为磁干扰的判断条件,用"8"字旋转方式进行实时校准。通过仿真和实验验证,新的方法有效地解决了磁力计误差补偿问题,证明了改进误差补偿算法的可行性和有效性。  相似文献   

10.
HMR3300电子罗盘是一种新型的磁航向传感器,能输出航向、俯仰、侧滚三个方向上的姿态数据,可以满足小型航向测量系统设计的要求。但该模块却易受外界干扰磁场的影响,因此,本文提出了一种电子罗盘和角速度陀螺配合使用的组合航向系统,并论述了HMR3300在该系统中的应用。  相似文献   

11.
A three-step computational technique for calibrating the magnetometers is proposed based on the functional minimization by means of a discrete Newton algorithm. A comparative analysis reveals that the technique proposed allows us to correct the data necessary for determining the azimuth by the Earth’s magnetic field.  相似文献   

12.
原子磁力仪可分为标量磁力仪和矢量磁力仪两大类。标量磁力仪的测量结果与传感器的姿态无关,对平台的机动不敏感。矢量磁力仪能够获得更多的磁场信息,可以实现更精确的磁源定位。目前,共有7种三轴矢量原子磁力仪,测量方法分别为磁场扫描法、磁场旋转调制法、磁场轮流抵消法、磁场投影法、磁场交叉调制法、磁场分立调制法和自旋进动调制法。重点对上述7种三轴矢量原子磁力仪的测量方法进行了整理和分析。  相似文献   

13.
分析了DG-1型多普勒/GPS组合导航系统,在不同工作方式下导航误差所引起的搜索方位角的误差;讨论了由于搜索方位角的变化引起的搜索域的变化。通过对机理的研究提出了解决办法。  相似文献   

14.
在太空探索中,磁场测量为很多重要的科学研究提供了数据支撑。空间探测器和磁测卫星均多次采用原子磁力仪作为磁场测量的主载荷,原子磁力仪在空间磁场测量中发挥着不可替代的作用。回顾了用于空间磁场测量的原子磁力仪的发展历程,总结了不同种类原子磁力仪的技术特点,分析了空间应用原子磁力仪载荷的发展趋势。  相似文献   

15.
The THEMIS mission includes a comprehensive ground-based measurement network that adds two additional dimensions to the information gained in the night magnetosphere by the five THEMIS spacecraft. This network provides necessary correlative data on the strength and extent of events, enables their onsets to be accurately timed, and provides an educational component in which students have an active participation in the program. This paper describes the magnetometers installed to obtain these ground-based North American magnetic measurements, including the magnetometers installed as part of the educational effort, and the support electronics provided by UCLA for the ground-based observatories. These magnetometers measure the Earth’s magnetic field with high resolution, and with precise timing provided by the Global Positioning System. They represent UCLA’s next generation of low-cost, ground-based magnetometers using an inexpensive personal computer for data collection, storage and distribution. These systems can be used in a stand-alone mode requiring only AC power. If there is Internet connectivity, they can be configured to provide near real-time data over the web. These data are provided at full resolution to the entire scientific community over the web with minimal delay.  相似文献   

16.
三轴磁通门传感器在军事和民用领域应用广泛,但由于其存在三轴非正交、零偏和标度系数不一致的问题,导致其存在转向差,影响了其磁测精度。首先,分析了转向差的产生机理,建立了误差模型,通过最小二乘法估算出了误差参数,进而对磁测数据进行了转向差校正。仿真计算表明,该算法对误差参数估算准确,对磁场分量和总场模值均有较好的校正效果,证明了算法的有效性。在磁场测量实验中,利用该算法估算出了传感器的误差参数,并对实测磁场数据进行了校正。校正后,数据的转向差得到了明显抑制,提高了三轴磁通门传感器的测量精度。  相似文献   

17.
The Magnetospheric Multiscale Magnetometers   总被引:2,自引:0,他引:2  
The success of the Magnetospheric Multiscale mission depends on the accurate measurement of the magnetic field on all four spacecraft. To ensure this success, two independently designed and built fluxgate magnetometers were developed, avoiding single-point failures. The magnetometers were dubbed the digital fluxgate (DFG), which uses an ASIC implementation and was supplied by the Space Research Institute of the Austrian Academy of Sciences and the analogue magnetometer (AFG) with a more traditional circuit board design supplied by the University of California, Los Angeles. A stringent magnetic cleanliness program was executed under the supervision of the Johns Hopkins University’s Applied Physics Laboratory. To achieve mission objectives, the calibration determined on the ground will be refined in space to ensure all eight magnetometers are precisely inter-calibrated. Near real-time data plays a key role in the transmission of high-resolution observations stored on board so rapid processing of the low-resolution data is required. This article describes these instruments, the magnetic cleanliness program, and the instrument pre-launch calibrations, the planned in-flight calibration program, and the information flow that provides the data on the rapid time scale needed for mission success.  相似文献   

18.
阵元位置误差有源估计方法研究   总被引:2,自引:2,他引:0  
阐述了对阵列天线阵元位置误差进行的研究,首先在天线阵列所在平面设置一个校正源,利用该校正源对阵元位置误差引起的阵列流形误差进行估计,然后将同一校正源放在不同方位角对阵列流形误差进行估计,最后经过矩阵运算估计出阵元位置误差。仿真证明此方法的有效性。  相似文献   

19.
Current technology has evolved low cost, highly reliable solid state vector magnetometers with excellent angular resolution. This paper discusses the role of a three-axis magnetometer as a new instrument for aircraft attitude determination. Using flight data acquired by an instrumented aircraft, attitude is calculated using the Earth's magnetic field vector and compared to measured attitudes. The magnetic field alone is not adequate to resolve all attitude variations and the need for a second reference angle or vector is discussed. A system combining the functions of heading determination and attitude measurement is presented to show that both functions can be implemented with essentially the same component count required to measure heading alone. lt is concluded that with the correlation achieved in calculated and measured attitude there is a potential application of vector magnetometry in attitude measurement systems.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号