共查询到17条相似文献,搜索用时 234 毫秒
1.
2.
王利明%郑玉峰%蔡伟%王中%赵连城 《宇航材料工艺》2000,30(3):5-10
重点评述了Ni-Ti-Nb宽滞后形状记忆合金自问世以来,国内外学者对其显微组织及亚结构,应变恢复特性,应力诱发马氏体相变和形变应力诱发马氏体的稳定性等与其形状记忆效应密切相关的研究成果,并在此基础上详细介绍了Ni-Ti-Nb宽滞后形状记忆合金在工程上,尤其是在航天航空工业中的应用情况。 相似文献
3.
4.
TiNiPd高温形状记忆合金相变温度与相变滞后的研究 总被引:2,自引:0,他引:2
回顾了在 Ti Ni二元系合金基础上发展起来的 Ti Ni-X三元系高温形状记忆合金及 Ni Al系高温形状记忆合金。重点研究了 Ti Ni Pd系合金成分、相变温度和相变滞后的关系。结果表明 :当 Pd的原子百分数大于3 3 %,相变点的增加尤为显著,Pd的原子百分数提高 1 %,将导致合金的相变温度升高 2 0℃,当 Pd的原子百分数为 4 0 %时,Ms点可达 3 79.8℃。温度滞后ΔT随 Pd含量的增加基本不变,只是在 Pd原子百分数达到4 0 %时ΔT略有增加。相变热ΔH随 Pd含量增大呈线性增加,非常明显 相似文献
5.
6.
低碳硅锰系TRIP钢热处理工艺的研究 总被引:2,自引:1,他引:1
仅含碳、硅、锰合金元素的结构钢,采用临界区等温淬火热处理工艺,得到铁素体、贝氏体和残余奥氏体三相组织。该钢在 Ms(马氏体转变开始温度)~Md(马氏体转变终止温度)d温度之间形变,应变诱导相变,相变诱发塑性──TRIP,其力学性能指标大大提高。本文通过显微组织观察,力学性能结果分析,对这种低碳硅锰系TRIP钢三种不同的热处理工艺制度进行了研究。 相似文献
7.
刘晓婷 《西安航空技术高等专科学校学报》2002,20(3):57-59
热处理的淬火工艺对材料性能有着很重要的影响,对淬火组织马氏体的认识尤显重要,通过对马氏体相变的深刻分析与研究,能更进一步认识马氏体的本质。特别是希望马氏体相变在更高的温度下完成,这对减小淬火变形和裂纹有着十分重要的意义。 相似文献
8.
Fe元素对TiNi形状记忆合金相变点和力学性能的影响 总被引:13,自引:4,他引:9
采用纯度均为99%的Ti,Ni和Fe原材料,在真空电弧炉中熔炼5次,制备出TiNiFe(Fe=2 5%,3 0%和3 5%)3种成分的TiNiFe合金铸锭,经850℃保温24h的真空均匀化处理后,锻造成 7mm的棒材。采用光学金相、电阻法和拉伸试验等方法研究了Fe含量对TiNi形状记忆合金晶粒度、相变温度和力学性能的影响。随着Fe的原子含量由2.5%提高到3.5%,TiNiFe合金的晶粒略有细化,晶粒大小从49μm减小到26μm,马氏体相变温度从-73.5℃下降到-190.0℃以下,抗拉强度和屈服强度也显著提高,延伸率δ没有明显变化。所研制的TiNiFe合金的马氏体相变温度和室温力学性能可满足航空管接头用记忆合金的要求。 相似文献
9.
介绍从NiTi形状记忆合金伪弹应力、回复应力与相变特征参量的内在联系出发,在实验的基础上利用计算机仿真技术建立回复应力与伪弹应力及温度、预应变之间关系的方法。 相似文献
10.
TiNiMo形状记忆合金的相变、形状记忆效应与力学性能研究 总被引:1,自引:0,他引:1
研究了TiNiMo形状记忆合金的相变特性、形状记忆效应和力学性能,结果表明:TiNiMo合金存在一个R相变,Mo的加入降低了TiNi合金的马氏体相变开始温度(Ms),Ti50Ni48.5Mo1.5和Ti50Ni48Mo2.0合金的Ms分别达到了-85℃,-103℃,这两种合金分别在8.51%和8.26%的预应变下获得了8.06%和7.71%的形状记忆效应。Ti50Ni48Mo2.0合金的屈服强度和抗拉强度分别为589MPa和799MPa,比Ti50Ni48Fe2.0的相应强度分别高73%和31%,同时Ti50Ni48.5Mo1.5的力学性能也较为优异,因而TiNiMo合金是很有发展潜力的新型的记忆合金接头材料。 相似文献
11.
YAN Zhu CUI Li-shan ZHENG Yan-jun 《中国航空学报》2007,20(2):168-171
The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology. 相似文献
12.
13.
14.
NiTiNb shape memory alloys have attracted much attention in pipe coupling or sealing system because of their large transformation hysteresis upon a proper pre-deformation. In order to clarify the effects of adding Nb on the mechanical properties as well as the transformation behavior of NiTiNb shape memory alloys, Ni47Ti44Nb9 and Ni49.8Ti45.2Nb5 alloys with different microstructures but with similar martensitic transformation start temperature, are prepared. Comparative studies on the microstructures, mechanical properties and transformation characteristics are conducted by means of scanning electron microscopy (SEM), phase transformation measurements and mechanical property tests. It is found that Ni47Ti44Nb9 and Ni49.8Ti45.2Nb5 alloys possess similar transformation hysteresis in the as-annealed state. However, the presence of Nb and its status exerts important effects on the mechanical properties, especially the yield strength and the yield behavior of the alloys. Ni49.8Ti45.2Nb5 alloy exhibits remarkable increase in the yield strength than the Ni47Ti44Nb9 alloy. The transformation hysteresis of both alloys under pre-deformation is characterized and the relative mechanism is discussed. 相似文献
15.
利用形状记忆合金(shape memory alloy,SMA)独特的超弹性效应,提出一种利用形状记忆合金提高复合材料结构抗低速冲击性能的方法.基于形状记忆合金的分段化线性简化模型,利用ABAQUS有限元软件提供的VUMAT子程序编制了SMA合金超弹性本构关系并将其引入到复合材料层板低速冲击模型,提出了含SMA复合材料低速冲击数值模拟方法.研究形状记忆合金利用迟滞阻尼特性吸收部分形变能量并加以释放的过程,探讨SMA纤维对复合材料层板抗冲击性能的增强规律.结果表明,随着SMA体积分数的提高,复合材料层板的冲击应力峰值和挠度会下降,但在低SMA体积分数(<10%)情况下,对挠度的改善作用不明显;同时随着SMA体积分数增加,单位体积SMA的冲击能量吸收率会降低,在SMA体积分数为5%~10%时,SMA纤维具有最高的能量吸收率.得出了SMA纤维具有改善复合材料抗冲击性能的作用的结论. 相似文献
16.
17.
NiTi形状记忆合金记忆效应衰减行为及其机理的研究 总被引:2,自引:0,他引:2
对近等原子比NiTi形状记忆合金经几种不同工艺处理后的记忆效应衰减行为进行了研究。利用透射电镜对其微观组织结构作了观察,并从微观结构方面入手,对记忆效应衰减机理进行了分析与探讨。 相似文献