共查询到19条相似文献,搜索用时 468 毫秒
1.
2.
3.
4.
5.
进行冰风洞试验时,出口过冷水滴的参数往往使用风洞来流空气参数进行计算,忽略了真实情况下水滴与空气的传热传质过程,致使试验数据产生偏差,并影响测试结果的可靠性.通过对冰风洞试验中水滴的运动过程进行研究,考察了水滴与空气主流间的传热与传质现象,建立了水滴运动过程中参数变化的控制方程.基于该方程编制了冰风洞水滴粒径温度变化分析软件,计算分析了过冷水滴在行进过程中相关参数的变化曲线,比较了不同初始条件及各参数对水滴温度、直径和速度的影响.结果表明:不同环境下水滴在运动过程中温度、尺寸和速度变化受来流温度、速度、相对湿度和水滴初始温度的影响,呈现出不同的特点,不能忽略水滴状态参数在冰风洞内的变化. 相似文献
6.
7.
沸石-水吸附床二维传热传质模型 总被引:1,自引:0,他引:1
建立了沸石—水吸附式制冷系统吸附床在非第1类边界条件时的二维传热传质模型。应用该模型进行了强化传热传质过程的研究,讨论了肋片数量、肋片物性参数、吸附床的有效导热系数、接触热阻等参数对脱附时间的影响。结果表明,增加肋片可以改善吸附床的性能,其中肋片的数量和接触热阻对性能的影响较大,而肋片本身的物性参数影响不大。 相似文献
8.
9.
为了深入认识复合材料的多尺度传热特性,预测复合材料宏观热物性参数,基于通用单胞思想和多尺度传热特性分析,建立了一种有效预测碳布叠层穿刺复合材料等效热物性参数的方法。基于电镜扫描分析了纤维束和编织结构的特征,采用通用单胞思想,建立了介/细观传热分析模型,通过数值仿真进行了一系列的多尺度传热特性分析,譬如:纤维体积分数对纤维束结构传热特性的影响、穿刺纤维束大小对编织结构传热特性的影响分析,在此基础上,建立了胞体模板扩展,初步将介/细观结构研究规律应用到宏观结构热物性预测,并进行多层胞体传热特性分析。验证实验表明:等效热物性预测值与实验值吻合较好,方法有效,为深入理解认识碳布叠层穿刺复合材料的介/细观传热特性提供了有效的分析手段。 相似文献
10.
11.
《中国航空学报》2021,34(9):119-132
The multiple jets impingement heat transfer is widely applied in the wing anti-icing system. It is challenging to apply the similarity criterion to carry out the anti-icing experiments due to the complex flow and heat transfer behavior. In the present study, the full-scale slat model is used to carry out anti-icing experimental researches in a 2 m × 3 m icing wind tunnel of China Aerodynamics Research and Development Center. The effects of icing parameters Liquid Water Content (LWC) and Median Volume Diameter (MVD) and hot air parameters (mass flow rate and temperature) on the thermal performance of an inner-liner anti-icing system with jets impingement heat transfer are studied. The effects of the experimental parameters are analyzed in detail by combining impingement and evaporation heat transfer mechanisms. The impingement hot air mass flow rate dramatically affects the heat transfer performance of the impingement stagnation region within the range of the experimental parameters. The temperature of impingement hot air and that of wing skin are approximately linear correlated. The experimental results show the effects of LWC and MVD on water film formation and runback ice accretion. The formation of water film is analyzed by an analytical method based on the wing skin temperature difference of dry and wet air conditions. 相似文献
12.
Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach. 相似文献
13.
14.
舱内热环境的有效预测是优化飞行器热控与防热设计、减小系统冗余并保障飞行器热安全的重要基础。在国家数值风洞(NNW)工程支持下,针对目前舱内热环境多尺度、多机制复合传热特点及其数值预测面临的精度与效率提升难题,发展了多区域协同推进的时空耦合模型及流/固界面的自适应分辨率识别算法,建立了基于热格子Boltzmann方法(TLBM)与有限体积法(FVM)相互耦合的舱内复合传热跨尺度预测方法,开展了典型飞行器仪器舱的综合热分析,验证了耦合方法的计算精度及效率。研究表明,相关方法可实现舱内热环境的局部精细化与整体大规模的协同模拟,用于开展整体自然对流与设备局部热量传递的多尺度数值模拟,掌握不同环境参数对舱内热质传递过程的影响规律,从而为飞行器热防护/热管理一体化设计提供重要技术支撑。 相似文献
15.
微矩形槽内的单相强迫对流换热性能实验 总被引:6,自引:0,他引:6
航空电子设备集成度和封装密度的增加给电子元器件的热控制问题带来了严峻的挑战,微槽散热器是解决航空电子元器件散热的一条有效途径。本文设计制作了6种不同结构尺寸徽矩形槽道,采用航空电子设备上最常用的乙醇溶液作为冷却工质,进行了徽槽道内单相强迫对流换热性能实验,分析了流体流速、过冷度和微槽结构等对传热特性的影响。 相似文献
16.
电动汽车驱动电机极力追求高密度轻量小型化,不断推进电机的冷却散热与热传导技术的进步与发展。为此,开展车用驱动电机的电-磁-热一体化设计方法研究,通过构建一种工程化定子热路模型提出了定子绕组热性能直接设计法及其关键热参数,并直接融入电磁设计中,强化热性能设计的同时也弥补了传统电磁设计热负荷AJ值评估热性能的缺陷。通过快速评估电机的热传导能力和绕组温升,可评估比较不同设计方案的热性能,得到电-磁-热一体化设计的最佳解决方案,从而提升电机持续运行的输出转矩。采用定子绕组热性能直接设计法,改进设计了一台液冷机壳车用永磁同步驱动电机样机,显著降低了定子绕组温升。样机温升试验验证了定子绕组热性能直接设计法及其关键热参数评估热性能的有效性。 相似文献
17.
18.
19.
针对多参数、强热耦合发动机热防护模型修正的难题,通过分析系统的传热特点,提出热环境分级、热参数分类的单参数调试方法。通过分析传热关系,将系统分为两级热环境;在每级热环境中仅调节几个参数,减少了调试工作量。通过分析热阻网络,确定了待定参数;通过分析参数的影响程度,确定参数的修正顺序。以具有代表性的两颗导航卫星为研究对象,利用I-DEAS TMG软件对发动机热影响过程进行仿真。调试结果表明:热模型的精度控制在2℃以内,提高精度后的热模型可用来验证、指导热控设计。单参数调试方法的原理基于各参数对不同部件的影响程度不同,可经有限次调试快速获得高精度、稳定的结果。单参数调试方法可用于解决工程实践中的多参数耦合问题。 相似文献