共查询到20条相似文献,搜索用时 234 毫秒
1.
简要介绍了飞机机翼整体壁板喷丸成形系统的结构,并对整体壁板建模、喷丸成形数据库、运动模拟及喷丸成形有限元模拟等模块的功能与实现作了说明。 相似文献
2.
针对6061-T6热处理强化铝合金焊后由“接头软化”导致的力学性能严重下降等问题,提出激光诱导电弧填丝焊及焊后局部轧制复合成形工艺,利用焊接接头余高的局部变形辅助强化接头“过时效软化区”。结果表明通过焊轧复合成形方法能得到成形良好且无缺陷的接头。与焊接接头相比,焊轧复合成形接头硬度整体更加均匀,软化最严重位置的硬度由71.2 HV提升到87.8 HV,提升了23.3%;焊轧复合成形接头的平均抗拉强度由246 MPa提升到284 MPa,相对提升了15.4%,达到母材的91.6%。轧制工艺使焊接接头发生局部强制变形,焊缝区等轴晶晶粒被压实且焊缝变宽。焊缝金属向两侧挤压使热影响区组织发生协同变形,导致位错密度增加,实现“过时效软化区”强化效果。 相似文献
3.
带筋整体壁板特别是高筋整体壁板具有优异的结构效率、减重效益和密封效果,在航空航天等领域备受青睐。预应力喷丸成形是大中型、长寿命、高性能复杂带筋整体壁板的一种不可多得的有效成形手段。数值模拟是促进带筋整体壁板预应力喷丸成形技术研究、进步与应用的一种极具潜力的途径。针对带筋整体壁板预应力喷丸成形数值模拟,建立了基于响应面函数的多弹丸撞击有限元模型、基于应变中性层内移的反弯曲应力场法模拟模型、预应力喷丸成形RBF神经网络预测模型,实现了喷丸成形应力场法数值模拟、预应力喷丸成形较高精度数值模拟与变形预测,为带筋整体壁板预应力喷丸成形技术研究和实际应用提供了一种更为便捷、高效、经济的途径。 相似文献
4.
主要针对线性摩擦焊制备整体叶盘的方法,利用在研发动机结构形式,设计了模拟样件;结合焊接设备、焊接夹具现状,设计了多种焊接接头,并进行了分析择优;采用强度分析和振动分析等手段,确定了焊缝位置范围;通过模拟样件的振动疲劳试验,对不同焊缝位置进行了性能评价,获得了较优的焊缝位置,为后续开展整体叶盘线性摩擦焊研究提供技术支持.设计和性能考核试验表明,焊缝位置在43 mm处较优. 相似文献
5.
针对整体壁板压弯成形过程中由于回弹导致的压弯成形精度低和不可控问题,提出整体壁板压弯成形形状控制方法。以铝合金(7050-T7451)机翼整体壁板为研究对象,设计了整体壁板缩比试件模型,基于弹塑性变形理论和几何分析建立了压弯成形局部变形下压量解析预测模型,基于有限元法建立了压弯成形整体变形有限元仿真预测模型,并将模拟结果与实验结果进行了对比;在压弯成形局部-整体变形预测模型的基础上,综合考虑局部-整体变形精度,利用迭代补偿机制与逐步逼近思想,构建了压弯成形轮廓曲线迭代模型。通过与传统的试错法进行对比,研究结果表明所提方法能够以更高的精度、更快的收敛速度有效控制压弯件的成形形状。 相似文献
6.
栅格零件是某型无人机中的关键功能结构,形状复杂,形貌精度控制要求较高,非常适合采用激光选区熔化(SLM)工艺进行制造。利用华中科技大学研发的iAdditive仿真软件对栅格零件的SLM成形过程进行仿真分析,对支撑与关键塑性变形位置的分区打印策略进行了设计和优化。结果表明:通过仿真模拟可以迅速获得SLM成形过程中的关键塑性变形位置,通过分区设计可以使关键堆积层的变形量减小大约60%;通过对比支撑切除之后的模拟结果与试验结果,两者之间的变形趋势和变形数值吻合良好,最大变形处在中间栅格区域,变形量约为2.0mm。 相似文献
7.
王宏伟%李庆芬%朱兆军%魏尊杰 《宇航材料工艺》2007,37(4):42-45
采用融熔沉积快速成形法制备钛金属蜂窝结构材料,对粉浆制备、钛金属蜂窝结构蜡坯固化、脱蜡等工艺以及所制备的钛蜂窝体的压缩性能进行了研究.结果表明,采用融熔沉积快速成形可以制备钛金属蜂窝结构,工艺简单、尺寸可控,钛蜂窝结构的相对密度在9%~12.6%范围内,屈服强度和弹性模量的增加不大;相对密度超过12.6%后,屈服强度显著增加,但弹性模量增加的幅度不大.通过改变蜂窝体正六边形的边长或改变蜂窝体的壁厚均达到相同的相对密度条件下,蜂窝体的压缩强度差别不大,但对蜂窝体的弹性模量却有显著影响. 相似文献
8.
三基圆缠绕成形(SJY)方法突出的优点是利用其组合、连接、分支和补强功能,可以成形无粘接和无损伤的整体承力刚架结构,从而弥补了复合材料层板的不足,扩展了复合材料的应用范围。这种成形工艺在无任何粘接、螺接和铆接和无任何局部损伤的条件下,制成全复合材料飞机的整体承力刚架。 相似文献
9.
10.
为研究局部进气条件下ATR涡轮内的流动特性,对局部进气涡轮进行定常和非定常数值模拟.定常计算采用冻结转子方法,改变动叶与静叶的周向相对位置研究涡轮内流场特征;改变进气扇区布局、进口参数和局部进气度,研究其对涡轮性能的影响.研究结果表明,对于给定局部进气度,进气扇区整体布局时,涡轮性能的优越性最大;在局部进气ATR涡轮的设计中,需要综合考虑流量、效率和功率3个因素来决定局部进气度.不同位置定常流动结果的平均值与非定常流动的时均值存在差异,非定常计算更好地展示了静叶尾迹和流动积累效应的影响,因而更加可靠. 相似文献
11.
通过精密测量相对密度化建立韧性损伤模型,以预测金属塑性加工过程中韧性损伤演化规律和产品质量。本文研究了精密测量微小密度的变化、介绍了测量方法和装置。通过测量相对密度变化对拉伸和扭转过程中韧性损伤演化规律进行了研究。 相似文献
12.
13.
14.
采用烧结 等温锻造的方法制备Ti-17粉末合金,对粉末合金制备过程中各工序的密度、显微组织变化规律等进行了试验研究.试验结果表明:经相同条件烧结后,-140目粉末烧结棒材和-80/ 140目粉末烧结棒材分别达到理论密度的98.06%和93.55%,在-80/ 140目粉末烧结棒材显微组织中观察到有大量的残留空隙存在.采用高低温等温锻造工艺能够有效去除粉末合金烧结后残留的空隙,提高合金的密度,使合金的显微组织得到显著细化和均匀化.烧结 等温锻造是制备优质粉末钛合金的有效方法. 相似文献
15.
《中国航空学报》2020,33(10):2794-2806
The unsatisfied surface quality seriously impedes the wide application of incremental sheet forming (ISF) in industrial field. As a novel approach, the interpolator method is a promising strategy to enhance the surface quality in ISF. However, the mechanism for the improvement of surface quality and the influence of interpolator properties on surface roughness are not well understood. In this paper, the influences of process variables (i.e. tool diameter, step size and thickness of interpolators) on the forming process (e.g. surface roughness, forming force and geometric error) are investigated through a systematic experimental approach of central composite design (CCD) in two-point incremental sheet forming (TPIF). It is obtained that the increase in thickness of interpolators decreases the surface roughness in direction vertical to the tool path while increases the surface roughness in direction horizontal to the tool path. Nevertheless, the combined influence between thickness of interpolators and process parameters (tool diameter and step size) is limited. Meanwhile, the placement of interpolator has little influence on the effective forming force of blank. In addition, the geometric error enlarges with the increase of step size and thickness of interpolator while decreases firstly and then increase with an increase in tool diameter. Finally, the influencing mechanism of the interpolator method on surface quality can be attributed to the decrease of the contact pressure due to the increase of contact area with the unchanged contact force. Meanwhile, the interpolator method eliminates the sliding friction on the surface of blank due to the stable relative position between the blank and the interpolator. 相似文献
16.
17.
18.
微桁架夹芯板点阵轻量化结构在航空航天领域有重要应用,选区激光熔化(SLM)增材制造技术可克服传统工艺局限性,高质量一体化成形复杂点阵结构。以稀土Sc改性高强Al-Mg合金为对象,采用SLM工艺对其进行工艺优化试验,并基于优化结果对微桁架夹芯板开展一体化成形工艺调控研究。研究结果表明:SLM成形Al-Mg-Sc-Zr合金表面质量、冶金缺陷等随激光参数发生显著变化,在激光功率400 W、扫描速度800 mm/s的条件下获得较高表面质量(粗糙度为13.2 μm)及致密度(相对密度为99.5%)。当扫描速度较低时试件熔池底部形成一次Al3Sc析出相,而当扫描速度过高时因凝固速度过快析出相减少,导致试件显微硬度降低。在优化工艺区间内,随激光扫描速度增加SLM成形Al-Mg-Sc-Zr微桁架夹芯板粘粉比例下降,构件质量随之减轻;水平方向构件尺寸精度、桁架微杆成形精度均随扫描速度增加而增加。 相似文献
19.
The isothermal local loading forming technology provides a feasible way to form Ti-alloy large-scale rib-web components in aerospace and aviation fields.However,the local load ing process forming limit is restricted by forming defects in the transitional region.In this work,the feasibility of controlling forming defects and improving the process forming limit by adjusting die parameters is explored through finite element (FE) simulation.It is found that the common cavum and folding defects in the transitional region are significantly influenced by the fillet radii of left rib and middle rib,respectively.The cavum and folding defects can be effectively controlled by increas ing the fillet radii of left rib and middle rib,respectively.The process forming limits considering forming defects in the transitional region are determined by the stepwise searching method under various die parameters.Moreover,the relationship between the process forming limit and die parameters is developed through the response surface methodology (RSM).The developed RSM models suggest that increasing the fillet radii of left and middle ribs is effective to improve the pro cess forming limit during local loading forming of rib-web components.The results will provide technical basis for the design of die parameters and the reduction amount,which is of great impor tance to control forming defects and improve the process forming limit in local loading forming of Ti-alloy large-scale rib-web components. 相似文献