Stepped Sinewave Inverter

A stepped sinewave dc/ac inverter was analyzed for an inductive load with respect to load current and voltage, harmonics, power factor, and efficiency. This special inverter of high efficiency and low harmonic content is constructed by synthesizing the sinusoidal output by discrete voltage sources, such as storage batteries, solar cell, etc., with electronic switching of the sources at specific time intervals. The switching times are determined for the condition of minimum distortion of the synthesized wave. A 50 W inverter was built and tested to demonstrate this approach.     

用微机控制的SPWM逆变器的研制

本文说明了利用 MCS-51系列单片机控制的 SPWM 型恒压恒频单相逆变器的设计思想,线路及其实现方法。为了改善在电感性负载下的输出波形,采用了方波及 SPWM 波混合控制的桥式功放电路。并采用了独特的调压方法,使输出波形及转换效率在不同负载下保持不变。该逆变器还具有电瓶亏电指示、过载保护、软起动等多种功能。最后给出实验结果。     

Single-phase grid-connected PV system using three-arm rectifier-inverter

A grid-connected photovoltaic (PV) power supply system with on-line voltage regulation capability is presented. It employs the three-arm rectifier-inverter topology with PV modules connected directly on the dc-link. The common-arm is with line-frequency switching and synchronous to the input voltage, aiming for a lower switching loss and decoupling the control of rectifier and inverter portions. As a result, the rectifier and inverter portions can be controlled independently with the rectifier-arm and inverter-arm, respectively. For maximum power point tracking (MPFF) of the PV modules and balancing the power among utility, PV, and the load, a variable dc-link voltage is adopted and controlled by the rectifier-arm based on the MPPT control algorithm. The inverter-arm then regulates the load voltage with good regulation and low distortion. Due to large variation of the dc-link voltage, a feedforward plus feedback control technique with variable gain is developed to keep constant bandwidth of the current loop at any operation condition. Therefore, the performance of the rectifier and inverter portions can be ensured. A system containing a 2 kVA converter and a 1.2 kW PV module is set up, and some experimental results are provided for demonstrating the effectiveness of the proposed method.     

Novel AC-DC and DC-DC converters with a diode-capacitor multiplier

This paper presents a transformerless ac-dc and or dc-dc converter with a high output voltage multiplicity, which contains only one switch. The converter consists of an inverter and a diode-capacitor multiplier (DCM) and provides a voltage gain equal to double the number of multiplier steps. In the case of ac-dc conversion the proposed converter offers a practically unit power factor and provides a sine wave input current. The analysis of the steady state as well as the transient behavior of the DCM is given and simplified equivalent circuits are proposed. The prototype of the DCM has been built and tested to show the validity of the proposed converter. The theoretical analysis, the computer simulation results, and the experimental testing results are in good agreement.     

ACSS for paralleled multi-inverter systems with DSP-based robust controls

An averaged current-sharing strategy (ACSS) for paralleled multi-inverter systems with digital signal processor (DSP)-based robust controls is presented. With an ACSS, the inverters are in parallel operation and each inverter has a voltage robust controller to achieve system stability and robustness, and a current robust controller to track the averaged inductor current of the inverters to achieve equal current distribution. In the proposed system, the current-sharing control loop is independent of the voltage control loop. Therefore, equal current distribution among the inverters, fast response, and tight regulation can be achieved. Additionally, the ACSS in each inverter can be readily implemented with two operational amplifiers. Simulation results and hardware measurements or a single-inverter system and a two-inverter system, and simulation results of a three-inverter system with linear and nonlinear loads have demonstrated the feasibility of the proposed control scheme in equal current distribution and fast regulation.     

一种新颖的在线自校正死区补偿策略

为解决正弦脉宽调制(SPWM)电压源逆变器在低频和轻载时死区效应所导致的相电压、相电流畸变和转矩脉动等问题,提出了一种新颖的在线自校正死区补偿策略。该策略考虑了死区时间、功率器件管压降、开通时间、关断时间等对逆变器输出电流的影响,而且对直流母线电压和载波频率的波动进行了自校正在线计算补偿。最后,对输出电流进行了死区补偿前和补偿后的对比试验,结果表明该方法具有较好的补偿效果。     

Resonant inverters for photovoltaic array to utility interface

A number of high-frequency link power converter schemes suitable for interconnecting a photovoltaic (PV) array to the utility line using resonant inverters are presented. Use of high-frequency resonant inverters (HFRI) results in reduced size, weight and cost. Scheme 1 uses the HFRI-cycloconverter, scheme 2 uses the HFRI-rectifier pulsewidth-modulated voltage source inverter, scheme 3 uses the HFRI-rectifier line commutated inverter working with a fixed maximum possible inverting fringe angle, and scheme 4 uses the HFRI-rectifier line-connected inverter (with line current modulation). These schemes are compared. Based on the comparison, scheme 3 was selected for an initial study. To overcome various problems associated with scheme 3, the line current is modulated sinusoidally in scheme 4. In this scheme, the HFRI is controlled appropriately to obtain a rectified sine wave of 120 Hz in the DC link and the function of the line-connected inverter is to unfold this waveform on alternate half cycles to obtain a sinusoidal line current with the line voltage. Methods of commutation of the line connected inverter are explained. Experimental results obtained with scheme 4 are presented     

一种改进的LCL并网逆变器控制方法的研究

LCL型滤波器相对于L型滤波器对交流侧电流中的高频谐波有更强的抑制能力,因此也越来越多地被用于逆变器中。研究了在独立工作模式和并网逆变模式间的切换过程中如何做到无扰动切换。在独立和并网逆变两种模式下分别对空载电压和并网电流直接控制。在对比传统电压电流控制情况下, 对电压电流控制进行改进。通过MATLAB/Simulink仿真平台,建立了LCL型滤波的逆变器并网模型,仿真分析证明了可行性。     

Bidirectional DC-to-AC inverter with improved performance

Switch-mode DC-to-AC inverters using DC-to-DC converter topology have many advantages over the traditional bridge-type inverter. A bidirectional power circuit combined with a nonlinear robust control is proposed to form a high performance inverter. The output voltage of the inverter can be stabilized regardless of large changes in input voltage and output current. The distortion near the zero crossing point can be minimized. The load of the inverter can be resistive, inductive, or capacitive. Simulation results and experimental verification are provided     

双Buck半桥逆变器输入电容电压脉动的分析

双Buck逆变器(DBI)是航空静止变流器(ASIs)的常用拓扑,从双Buck半桥逆变器(DBHBIs)两直流电感中分离出交流电感使得体积、重量进一步减小。在正常工作,尤其是负载短路情况下,双Buck半桥逆变器输入侧电容上的电压产生与输出同频的脉动。以交流电感分立的双Buck半桥逆变器为例,分析了在额定负载、短路、级联工作等情况下输入电容电压脉动的产生原因,给出了该脉动的定量计算方法,并由此得出了输入侧电容容值的选择依据。最后通过仿真和实验,验证了文中分析的正确性。该分析方法同样适用于其他半桥型逆变器拓扑。     

基于载波调制 PWM的对称六相与三相 PMSM串联系统矢量解耦控制

针对对称六相与三相 PMSM串联系统的解耦控制问题,基于串联系统的数学模型,在二相旋转坐标系下进行了漏感压降补偿,并基于坐标变换和控制量叠加得到了逆变器期望输出。在解耦控制的工程实现方面,充分考虑了逆变器电压、电流限制,提出 1种直流母线电压分配方法,提高了系统运行的可靠性。实验证明,所提控制策略能够实现 2台电机在负载或转速突变情况下的解耦运行。     

基于降阶谐振控制器的三相逆变器电压控制研究

针对三相逆变器输出侧接非线性负载时输出电压的质量易受谐波影响的问题,选用基于降阶谐振控制器(RRSC)的电压控制方法。与谐振控制器相比,RRSC能够进行正负序的分离,然后分别处理,并且计算量小,运算效率高。为了在此基础上再次降低输出电压谐波含量,进一步改进了RRSC,并将其用于三相逆变器电压控制。最后,对所提控制方法进行了仿真验证,并与降阶谐振控制方法进行了详细分析对比。仿真结果证明了所提控制方法的有效性。     

基于重复控制技术的单相航空静止变流器的研究

针对航空静止变流器带非线性负载造成的输出电压波形畸变问题,分析了采用重复控制技术的单相静止变流器控制模型和补偿器的数学表达形式。给出了控制器参数的频域设计方法。通过单相500VA/400Hz静止变流器的原理样机实验,其结果表明此分析设计方法是正确可行的。同时也验证了采用重复控制技术解决航空静止变流器带非线性负载时的输出波形畸变问题是行之有效的。从而为三相大功率航空静止变流器的研制打下了良好的基础。     

Novel single-stage half-bridge series-resonant buck-boost inverter

A novel single-stage half-bridge series-resonant buck-boost inverter (HB-SRBBI) is proposed. The main attribute of the novel inverter topology is the fact that it generates an ac output voltage larger or lower than the dc input one, depending on the instantaneous duty cycle. This property is not found in the classical voltage source inverter (VST), which produces an ac output instantaneous voltage always lower than the dc input voltage. The proposed inverter circuit topology provides the main switch for turn-on at zero-current-switching (ZCS) by an auxiliary resonant cell built before the output choke. A state-space averaging approach is employed to analyze the system. A design example of 500 W ac/dc inverter is examined to assess the inverter performance and it provides high power efficiency above 90.7% under the rated power.     

Z源三相四桥臂逆变器的三维空间矢量脉宽调制策略

对Z源三相四桥臂逆变器的稳态工作原理进行了深入分析,并提出一种改进的三维空间矢量脉宽调制策略,通过合理地选择直通桥臂,将直通状态插入到传统零矢量状态中,保证不影响有效开关状态和输出电压。同时,分析了直通占空比和调制比的耦合关系,得出直通占空比的最大取值,进而提出相应的最大恒定升压控制策略。在MATLAB/Simulink中搭建Z源三相四桥臂逆变器仿真模型,并在平衡及不平衡负载工况下进行仿真。仿真结果表明:Z源三相四桥臂逆变器在所提三维空间矢量脉宽调制策略下,不仅可以实现升压控制,而且相较传统Z源三相三桥臂逆变器,在不平衡负载条件下也能取得良好的控制效果。     

一种用于反舰导弹串联战斗部的环形切割器优化设计

为了优化设计用于反舰导弹串联战斗部前端的环形切割器,利用ANSYS／LS—DYNA有限元分析软件对相等装药条件下,不同药型罩开口角度、不同装药形状的环形切割器对靶板的切割效果进行仿真分析。仿真结论表明,60°锥角、组合体装药形状的环形切割器对靶板的切割效果更为理想。通过与相关试验数据的对比,初步验证了数值仿真的准确性。该结论有助于新型环形切割器的优化设计。     

A new power collection architecture for future spacecraft

The generalized tree-like transmission line network system having n layers in total with m-to-1 branch connection at each joint (T-TLNS-n-m) is proposed to replace the traditional series-parallel combined dc networks to automatically accumulate identically distributed power cells into the large amount of useful power for the spacecrafts. The proposed system has the attractive features of simple structure, easy construction and maintenance, and low cost, because two kinds of parts, ac current sources and m-to-1 transmission line (TL) branch connection parts, are used in the whole system. A method of implementing ac current cells having high output impedance is proposed to improve the power collection efficiency of the whole network system. Simulated results show that that low-pass nominal /spl pi/- or T-circuit with high characteristic impedance, which is used for the voltage source to current source converter in the current cell, improves the efficiency of the voltage inverter, filters out the harmonics, and increases the output impedance of the whole current cell.     

Current distribution control for parallel connected converters. II

For pt.I, see ibid., vol.28, no.3, p.829-840 (1992). In the central-limit control (CLC), the multiloop controls are employed to regulate the output voltage and track the central weighted current, thus equalizing the output current of each converter module (CM). The current distribution error (CDE) between the output current of each CM is used as a criterion in judging system performance. The prediction and simulation results of this control scheme are illustrated. When incorporated with the maximum current limit, the proposed control method can determine the number of required converters in the active state for each load condition. As a result, the efficiency of a system can be increased significantly. A comparison between the performances of the system under master-slave control (MSC) and CLC is given     

高速磁悬浮电动机变频器用开关电源设计

采用基于NCP1200的电流型控制,设计并研制了应用于高速磁悬浮电动机变频器的开关电源,该电源自适应输入电压波动,并自动调节PWM占空比以保证输出电压恒定.实验结果表明,该电源具有输出纹波小、效率高、EMI小、电压调整率和稳压性能好等优点,可用作变频器控制电路的电源.     

Frequency-controlled series-resonant converter with synchronous rectifier

This paper presents an analysis and experimental results for a frequency-controlled series-resonant dc-dc converter that consists of a Class-D zero-voltage-switching (ZVS) series-resonant inverter and a center-tapped synchronous rectifier. If the dc output voltage is low, the efficiency of the converter is dominated by the efficiency of the rectifier. Low on-resistance metal-oxide-semiconductor field-effect transistors (MOSFETs) are used in the rectifier instead of diodes because the forward voltage drop across the rectifying device is low, resulting in a high efficiency. The dc output voltage is regulated against variations in the load resistance and the dc input voltage by varying the operating frequency. Experimental results are presented for a converter with a dc input voltage of 150 V, an output voltage of 5 V, and a dc load resistance ranging from 0.5 to 5.5 R. The measured efficiency was 86% for a 50 W output and 89% for a 25 W output. The theoretical results were in good agreement with the measured results.