一种基于多普勒频率的恒模信号直接定位方法

相比于传统的差分多普勒(DD)两步定位方法,以Amar和Weiss提出的基于多普勒频率的单步直接定位方法在低信噪比和小样本条件下具有更高的定位精度。在该类新型定位体制的基础上,提出了一种基于多普勒频率的恒模信号直接定位方法。首先,依据最大似然(ML)准则以及恒模信号的恒包络特征,建立相应的直接定位优化模型。然后,根据目标函数的代数特征将全部未知参量分成两组,并提出一种有效的多参量交替迭代算法,用以获得该优化问题的最优数值解。新算法包含了针对这两组未知参量的Newton型迭代公式,用以避免网格搜索,并能实现多维参数的"解耦合"估计。最后,推导出针对恒模信号的目标位置直接估计方差的克拉美罗界(CRB)。数值实验验证了新方法的优越性。     

存在观测站位置误差的转发式时差无源定位

无源定位中,由于观测站安放在运动平台等原因造成的观测站位置误差会影响无源定位精度性能。另外到达时间差(简称时差)(TDOA)的转发式测量需要将不同观测站截获到的辐射源信号都转发到同一位置,如主观测站。针对这两个问题,提出了基于约束总体最小二乘(CTLS)的无源定位算法。首先将转发式时差的非线性定位方程转化为不需要中间变量的直接线性方程,再基于CTLS算法依次转化为约束优化问题和无约束优化问题,最后推导给出定位近似闭式解。仿真实验表明在观测站误差较大时,该算法与其他算法相比定位精度性能较好。     

直达与非直达环境中的多目标解耦直接定位方法

针对直达（LOS）与非直达（NLOS）环境中的定位问题,提出了一种波形已知条件下的单阵地多目标直接定位（DPD）算法。该算法针对发射时间已知和未知两种情况,利用多径信号到达角度与时延关于障碍物（或反射体）、观测站与目标位置参数的数学关系,建立了三维目标位置的最大似然（ML）函数,无需估计测量参数,避免了传统两步定位方法所需的非直达径识别与数据关联。为了克服多目标定位中的高维非线性优化问题,该算法利用独立波形信息将多目标定位解耦为对各个目标单独求解。通过对目标函数有效近似,算法在发射时间已知和未知两种情况下均仅需三维网格搜索,比相应的两步定位方法具有更低的计算量。此外,基于多径定位场景,推导了发射时间已知和未知两种情况下的位置估计克拉美罗界（CRB）。仿真结果表明：算法的定位性能能够逼近相应的克拉美罗界,比传统两步定位方法和子空间直接定位算法具有更高的定位精度。     

基于单个长基线干涉仪的运动单站直接定位

针对以往单站无源定位系统中采用的多通道干涉仪或阵列测向系统复杂、易受通道间幅相不一致性影响等缺点,提出了一种基于信号子空间分解的运动单站单个长基线干涉仪(LBI)直接定位(DPD)方法。该方法采用量子粒子群优化(QPSO)方法获得定位初值,再利用Newton迭代方法得到精估计值。仿真结果表明:增加观测器的机动性,可对辐射源实现快速无模糊的定位;定位性能在较高信噪比(SNR)下可接近定位误差的克拉美-罗下限(CRLB),在低信噪比下优于多通道干涉仪仅测角(BO)和长基线相位差变化率定位方法。     

基于单个长基线干涉仪的运动单站直接定位

 针对以往单站无源定位系统中采用的多通道干涉仪或阵列测向系统复杂、易受通道间幅相不一致性影响等缺点,提出了一种基于信号子空间分解的运动单站单个长基线干涉仪(LBI)直接定位(DPD)方法。该方法采用量子粒子群优化(QPSO)方法获得定位初值,再利用Newton迭代方法得到精估计值。仿真结果表明:增加观测器的机动性,可对辐射源实现快速无模糊的定位;定位性能在较高信噪比(SNR)下可接近定位误差的克拉美-罗下限(CRLB),在低信噪比下优于多通道干涉仪仅测角(BO)和长基线相位差变化率定位方法。     

未知互耦条件下混合信号波达方向估计

阵列天线互耦对导向矢量的扰动以及信号相干性对数据协方差矩阵造成的秩损,使得基于子空间正交性原理的超分辨波达方向估计(Direction-of-Arrival,DOA)算法性能恶化,甚至失效。针对这一问题,提出一种在相干与非相干信号混合状态下无需阵列互耦补偿的特征矢量平滑DOA估计算法。该算法对部分阵元接收数据的协方差矩阵特征分解,将得到的特征矢量平滑处理后构造等效协方差矩阵,抑制阵列互耦影响的同时完成混合信号DOA估计。在阵列互耦和信号相干性均未知的条件下,正确估计了信号DOA,无需互耦参数估计或补偿。计算机仿真结果验证了算法的有效性。     

回溯降维相干分布式非圆信号DOA快速估计

在相干分布式非圆(CDNC)信号波达方向(DOA)估计中,针对阵列输出矩阵扩展后维数增加带来的较大运算量问题,基于降维的多级维纳滤波(MSWF)技术,引入回溯优化思想,提出了一种快速估计算法。该算法首先利用信号非圆特性扩展阵列输出矩阵,然后通过MSWF递推分解快速求出信号子空间,避免了计算阵列协方差矩阵及特征分解,并且在递推过程中引入回溯优化机制提高了各级匹配滤波器的估计性能,最后由最小二乘(LS)或者总体最小二乘(TLS)得到DOA估计。仿真分析表明,所提算法与相干分布式非圆信号旋转不变子空间算法(CDNC-ESPRIT)性能相当,但复杂度得到了大幅度降低,相比于基于MSWF的非圆信号快速子空间(NC-MSWF-FS)算法,在较小的复杂度代价下大幅度提升了低信噪比时的估计性能,并且对初始参考信号的选取具有了较强的鲁棒性。     

修正容积卡尔曼滤波数据域直接定位算法

为解决数据域直接定位（DPD）算法面临的计算压力,提高算法效率,提出一种基于修正的容积卡尔曼滤波（MCKF）的DPD算法。首先,融合各观测信号波达方向信息,利用子空间数据融合方法建立一种基于间接观测量的DPD滤波模型;然后,根据模型特点设计MCKF算法进行求解,解决间接观测量带来的噪声累积问题;最后,对算法计算量进行分析和对比,说明计算效率的提升。仿真结果表明,所提算法与基于最大似然遍历搜索和遗传算法的DPD算法相比,在相同的估计性能下,计算量下降明显,时效性显著提升,增加了算法实用价值。     

运动单阵元被动合成阵列波达方向估计

 提出了一种运动单阵元被动合成阵列波达方向(DOA)估计算法。该算法基于被动合成阵列(PSA)的概念,结合空间谱估计的思想构建了运动单阵元被动合成阵列模型,通过多次不同速度合成阵列过程实现对信号DOA的无模糊估计。通过对单次匀速合成阵列过程进行分析得到,在假设信号频率已知条件下,合成阵列算法能够达到与同孔径实阵列多重信号分类（MUSIC）算法相当的DOA估计性能。仿真验证了被动合成阵列与同孔径实阵列的渐近等效性及算法的有效性。     

聚焦变换在MIMO阵列方位估计中的应用

MIMO阵列是近年来信号处理领域提出的一种新体制阵列技术,可有效避免常规阵列中的相干源问题。为解决多载波造成的方位模糊,提出了一种基于聚焦变换的MIMO阵列目标方位估计方法。该方法将MIMO阵列接收信号分解为多个频率分量的信号,并通过聚焦算法将多个频率信号聚焦到同一信号子空间,然后对聚焦后的信号进行方位估计。仿真结果表明:与直接对MIMO阵列接收信号进行方位估计相比,该方法利用了MIMO阵列的回波不相干性和宽带信号能量,具有更好的分辨能力和更高的方位估计精度。     

Approximate Maximum Likelihood Algorithm for Moving Source Localization Using TDOA and FDOA Measurements

 A closed-form approximate maximum likelihood (AML) algorithm for estimating the position and velocity of a moving source is proposed by utilizing the time difference of arrival (TDOA) and frequency difference of arrival (FDOA) measurements of a signal received at a number of receivers. The maximum likelihood (ML) technique is a powerful tool to solve this problem. But a direct approach that uses the ML estimator to solve the localization problem is exhaustive search in the solution space, and it is very computationally expensive, and prohibits real-time processing. On the basis of ML function, a closed-form approximate solution to the ML equations can be obtained, which can allow real-time implementation as well as global convergence. Simulation results show that the proposed estimator achieves better performance than the two-step weighted least squares (WLS) approach, which makes it possible to attain the Cram閞-Rao lower bound (CRLB) at a sufficiently high noise level before the threshold effect occurs.     

Direct position determination using single moving rotating linear array: Noncoherent and coherent processing

To improve the resolution and accuracy of Direct Position Determination (DPD), this paper investigates the problem of positioning multiple emitters directly with a single moving Rotating Linear Array (RLA). Firstly, the geometry of the RLA is formulated and analysed. According to its geometry, the intercepted noncoherent signals in multiple interception intervals are modeled. Correspondingly, the MUltiple SIgnal Classification (MUSIC) based noncoherent DPD approach is proposed. Secondly, the synchronous coherent pulse signals are individually considered and formulated. And the coherent DPD approach which aims for localizing this special type of signal is presented by stacking all array responses at different interception intervals. Besides, we also derive the constrained Cramér-Rao Lower Bound (CRLB) expression for both noncoherent and coherent DPD with RLA under the constraint that the altitudes of the emitters are known. At last, computer simulations are included to examine the performance of the proposed approach. The results demonstrate that the localization accuracy and resolution of DPD with single moving linear array can be significantly improved by the array rotation. In addition, coherent DPD with RLA further improves the resolution and increases the maximum emitter number that can be localized compared with the noncoherent DPD with RLA.     

A direct position determination method with combined TDOA and FDOA based on particle filter

The localization of a stationary transmitter using moving receivers is considered. The original Direct Position Determination (DPD) methods, with combined Time Difference of Arrival (TDOA) and Frequency Difference of Arrival (FDOA), do not perform well under low Signal-to-Noise Ratio (SNR), and worse still, the computation cost is difficult to accept when the computational capabilities are limited. To get better positioning performance, we present a new DPD algorithm that proves to be more computationally efficient and more precise for weak signals than the conventional approach. The algorithm partitions the signal received with the same receiver into multiple non-overlapping short-time signal segments, and then uses the TDOA, the FDOA and the coherency among the short-time signals to locate the target. The fast maximum likelihood estimation, one iterative method based on particle filter, is designed to solve the problem of high computation load. A secondary but important result is a derivation of closed-form expressions of the Cramer-Rao Lower Bound (CRLB). The simulation results show that the algorithm proposed in this paper outperforms the traditional DPD algorithms with more accurate results and higher computational efficiency, and especially at low SNR, it is more close to the CRLB.     

Acoustic node calibration using a moving source

Acoustic nodes, each containing an array of microphones, can track targets in x-y space from their received acoustic signals, if the node positions and orientations are known exactly. However, it is not always possible to deploy the nodes precisely, so a calibration phase is needed to estimate the position and the orientation of each node before doing any tracking or localization. An acoustic node can be calibrated from sources of opportunity such as beacons or a moving source. We derive and compare several calibration methods for the case where the node can hear a moving source whose position can be reported back to the node. Since calibration from a moving source is, in effect, the dual of a tracking problem; methods derived for acoustic target trackers are used to obtain robust and high resolution acoustic calibration processes. For example, two direction-of-arrival-based calibration methods can be formulated based on combining angle estimates, geometry, and the motion dynamics of the moving source. In addition, a maximum likelihood (ML) solution is presented using a narrowband acoustic observation model, along with a Newton-based search algorithm that speeds up the calculation the likelihood surface. The Cramer-Rao lower bound (CRLB) on the node position estimates is also derived to show that the effect of position errors for the moving source on the estimated node position is much less severe than the variance in angle estimates from the microphone array. The performance of the calibration algorithms is demonstrated on synthetic and field data.     

基于MCIS技术的相位差变化率单站无源定位

针对最大似然估计（ML）方法求解测相位差变化率单站无源定位问题计算量大、定位慢的问题,本文提出一种利用蒙特卡洛重要性抽样技术（MCIS）高精度、低复杂度的估计方法。根据Pincus定理推导出ML问题的近似全局解,利用重要性抽样（IS）技术构建符合高斯分布概率密度（PDF）的重要性函数,作为样本选取的依据,通过逆变换采样获得样本集,统计样本均值直接得到辐射源位置估计结果。MCIS方法简单易实现且运算量低,能够克服传统ML估计多维网格搜索耗时较长的缺陷,而且对目标位置初始估计误差有较低的敏感性。实验结果表明,MCIS算法在相同测量噪声水平下,定位精度优于EKF、NLS算法,有效减小了初始化估计误差对算法定位精度的影响,也进一步讨论分析了算法参数和不同观测条件对定位性能的影响。     

Pursuer identification and time-to-go estimation using passive measurements from an evader

We present an algorithm for identifying the parameters of a proportional navigation guidance missile (pursuer) pursuing an airborne target (evader) using angle-only measurements from the latter. This is done for the purpose of classifying the missile so that appropriate counter-measures can be taken. Mathematical models are constructed for a pursuer with a changing velocity, i.e., a direction change and a speed change. Assuming the pursuer is launched from the ground with fixed thrust, its motion can be described by a four-dimensional parameter vector consisting of its proportional navigation constant and three parameters related to thrusting. Consequently, the problem can be solved as a parameter estimation problem, rather than state estimation and we provide an estimator based on maximum likelihood (ML) to solve it. The parameter estimates obtained can be mapped into the time-to-go until intercept estimation results are presented for different scenarios together with the Cramer-Rao lower bound (CRLB), which quantifies the best achievable estimation accuracy. The accuracy of the time-to-go estimate is also obtained. Simulation results demonstrate that the proposed estimator is efficient by meeting the CRLB.     

基于恒模特性的QPSK-DSSS信号扩频序列估计

 针对非合作低信噪比条件下的QPSK-DSSS信号,提出一种基于恒模特性的扩频序列估计算法。该算法首先将单用户QPSK-DSSS信号等效为两用户的BPSK-DSSS信号,其次通过对信号协方差矩阵进行特征分解,估计出由同相与正交两路扩频序列张成的二维信号子空间,最后利用扩频序列的恒模特性消除特征分解带来的酉阵模糊问题,实现扩频序列的精确估计。本文提出算法实现简单,相对目前现有传统算法具有较低的计算复杂度,而且计算机仿真表明:本文提出算法在低信噪比条件下具有优良的估计性能。