共查询到20条相似文献,搜索用时 247 毫秒
1.
2.
3.
靠拢了固定几何流通截面的双模态超燃烧烧室模,采用气动热力调节的方法来实现双模态,宽马赫范围工作。计算结果表明,气动热力调节实现燃烧室内燃烧模态的转变是可行的。 相似文献
4.
针对超燃冲压发动机研究中对燃烧室出口温度场的测量需求以及暂冲式超燃冲压发动机燃烧台架试验中的应用难点,开发了适用于瞬态燃烧场温度测量的单脉冲相干反斯托克斯拉曼反射(CARS)系统及CARS光谱计算和温度反演软件CARSCF。采用USED相位匹配方式来降低湍流影响,结合多尺度小波分析方法来实现CARS光谱降噪处理,提高信噪比。在暂冲式脉冲燃烧风洞上开展了来流马赫数2.6条件下超燃冲压发动机燃烧室出口温度测量试验,获取了超声速来流(冷态)建立、H2点火加热空气、建立超声速燃烧流场直至试验结束过程中的燃烧室出口温度,以及煤油/空气燃烧时燃烧室出口温度场分布。结果显示,超声速冷流时温度处于低温(约205K)状态,随着H2点火加热来流空气,来流温度上升至853K;随着煤油/Air点火,温度急剧上升,稳定燃烧状态下燃烧流场温度为1970K±144K。燃烧室出口截面温度场分布测量结果显示,高温区位于燃烧室出口截面上侧区域,而燃烧室出口截面上中间区域的温度低于上下两侧。燃烧室出口温度分布CARS测量结果与火焰自发光成像结果一致,表明单脉冲CARS技术用于瞬态燃烧流场温度测量的可行性。 相似文献
5.
为研究超燃冲压发动机分级喷注的性能特点,基于双支板燃烧室开展变当量比喷注下的燃烧现象、释热规律以及发动机内推力性能试验研究。燃烧室入口马赫数2,总温1436K。煤油流量的调节速率分别为11.97g/s~2和35.90g/s~2。不同当量比调节速率的试验表明,当量比调节速率不影响试验结果。随着上游当量比的减小,上游火焰由充满支板尾部逐渐转变为在剪切层附近分叉。试验中发现,燃烧室存在两种稳定的燃烧状态:上游燃烧状态和下游燃烧状态。上游燃烧状态下,上游当量比相同而下游当量比不同时,燃烧室内推力差别不显著;下游燃烧状态下,增加上游喷注会提高燃烧室性能。上游燃烧状态变化到下游燃烧状态的上游当量比为0.19。在相同总当量比下,上游多分配当量比获得的上游燃烧状态可使内推力增加。 相似文献
6.
7.
可变几何径向涡流器流量特性及流量系数的试验研究 总被引:1,自引:0,他引:1
可变几何燃烧室是解决高温升、大热负荷燃烧室设计的关键技术之一。本文研究了可变几何径向涡流器在不同开度条件下的流量特性及流量系数变化规律。实验表明,采用这一技术可以在较大的范围内调节控制燃烧区和头部的当量比,以适应高温升、大热负荷燃烧室在广阔工作范围内保证燃烧室具有良好性能的需要。 相似文献
8.
凹腔作为超声速燃烧室的典型构型,对燃烧状态下的相关物理量进行准确诊断,有利于定量分析和研究超声速燃烧的机理。相对此前采用激光纹影等通程积分密度场显示方法,研究设计了一套锐聚焦深度小于1mm的激光聚焦纹影,用于显示凹腔截面的燃烧流场波系结构;同时利用羟基平面激光诱导荧光(OH-PLIF)和聚焦纹影同步诊断同一截面的温度场和密度场。试验结果表明,所显示截面内的波系结构清晰,得到了更多流场细节,同时也标记出了该截面内氢气燃烧状态,二者具有较好的一致性。该同步诊断结果可以更好地了解剪切层在燃烧室的运动及燃烧发展轨迹,以及不同参数的氢气喷射对剪切层和燃烧状态的影响等。获取同一截面的波系结构和燃烧状况的同步数据,对于研究燃料喷射以及凹腔燃烧等具有一定的参考价值。 相似文献
9.
10.
针对污染效应对超声速燃烧室熄火性能影响问题,采用甲烷燃烧和电阻加热的燃烧室直连式对比实验方法,开展了污染效应对燃烧室贫油熄火极限影响研究。基于超声速燃烧室实验模型,研究了煤油喷嘴结构对贫油熄火极限的影响;采用高速摄像仪和平面激光诱导荧光技术(PLIF),研究了加热方式对贫油熄火极限的影响,获得了光学测量结果和壁面压力分布,给出了纯净来流和污染来流条件下的燃烧室贫油熄火极限。研究表明:采用甲烷燃烧加热的燃烧室贫油熄火极限对应的当量比高于电阻加热的,分别为0.135和0.105;不同加热方式来流条件下,超声速燃烧室在燃烧不同阶段的稳定模式均为凹槽火焰稳定模式,火焰基底会呈现一定程度的脉动,但稳定在凹槽剪切层内。 相似文献
11.
Alexey Gennadievich VOROBYEV Svatlana Sergeevna VOROBYEVA Lihui ZHANG Evgeniy Nikolaevich BELIAEV 《中国航空学报》2019,32(2):253-262
This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval. 相似文献
12.
13.
固体推进剂裂纹对流燃烧和扩展的研究分析 总被引:5,自引:4,他引:5
评述了固体推进剂裂纹对流燃烧及扩展的研究,讨论了推进剂裂纹对流燃烧的流场与裂纹的变形、扩展及其之间存在着强耦合作用。初步揭示了在不同的燃烧室压力率下单一裂纹扩展的不同模式,指出裂纹腔内火焰的离散传播、裂纹尖端的压力突升以及对流燃烧条件下的裂纹失稳扩展极可能诱导产生DDT过程,提出了需进一步深入研究的问题。 相似文献
14.
15.
16.
To research the self-ignition characteristics of high-speed ramjet kinetic energy projectile in the launch process, the self-ignition process based on the solid fuel of polyethylene was numerically simulated by using the dynamic grid technology. The effect of different muzzle velocity on the self-ignition performance, and the effect of opening the blockage at different times on the flow field stability of the combustion chamber and the flow field characteristics after the solid fuel ramjet stabilized were analyzed. The results show that the occurrence of self-ignition is not only related to the pressure, temperature in the combustion chamber, and the muzzle velocity, but also to the content of C_2H_4 and its degree of mixing with air in the combustion chamber. After the kinetic energy projectile gets out of the muzzle and before the blockage opens, there is oscillation occurring in the combustion chamber. The higher the muzzle velocity of the kinetic energy projectile, the more prone to the occurrence of the self-ignition and the negative effects can be avoided due to the pressure oscillation in the combustion chamber. The effect of opening the blockage at different times on the flow field stability after the self-ignition occurs in a period of time is weak. After the blockage opens, the solid fuel ramjet can reach a stable working condition quickly. 相似文献
17.
18.
氧化剂气量配比对Mg/CO2发动机性能影响实验 总被引:1,自引:1,他引:0
基于国内外粉末火箭发动机的研究基础以及工业上粉体燃烧器设计方法,提出了一种Mg/CO2粉末火箭发动机构型和氧化剂气体分3次进气的燃烧组织方案,并针对其工作过程开展了实验研究。主要研究了在氧燃比为4∶1条件下,氧化剂不同进气方案时发动机的燃烧效率和燃烧室内沉积情况,从而为后续的Mg/CO2发动机多次起动实验工况参数设定提供依据。发动机热试实验结果表明:当燃烧室头部氧燃比较大时,发动机稳焰失败,无法正常工作;发动机热试实验中燃烧效率最高为64.0%;当氧化剂进气方案满足流化气、旋流气与侧向气量配比为2∶0.5∶1.5时,燃烧室内基本无沉积。 相似文献
19.
介绍了径向式可变几何旋流器开度特性计算方法,随着航空发动机推重比(p/w)的不断提高,涡轮前温度在逐年提高,目前先进发动机涡轮前温度高达1800K。燃烧室工作油气比(F/A)将由0.02增至0.03,为了保证发动机燃烧室在较宽的工作油气比范围内具有最佳性能,采用径向式可变几何旋流器是有效技术途径之一,本文从数学关系上建立了该种旋流器开度特性的计算方法并给出算例。可供可变几何燃烧室设计参考。 相似文献