Development of three-phase switch-mode rectifier using single-phase modules

This paper presents a three-phase (3/spl phi/) switch-mode rectifier (SMR) consisting of three 1 /spl phi/ SMRs, two center-tapped autotransformers and three changeover switches. The ac input sides of three modules are /spl Delta/-connected, and their dc output sides are connected in parallel. As any one module fault occurs, the remaining two modules becomes modified T-connected and continuously perform three-phase rectification with good line drawn power quality. When two constituted 1/spl phi/ modules are faulted, the proposed 3/spl phi/ SMR will be operated as 1/spl phi/ SMR. The quantitative and robust voltage regulation controls for the developed SMR are made to consider the effects of changes of system parameters, operating condition, and number of connected modules.     

A new power collection architecture for future spacecraft

The generalized tree-like transmission line network system having n layers in total with m-to-1 branch connection at each joint (T-TLNS-n-m) is proposed to replace the traditional series-parallel combined dc networks to automatically accumulate identically distributed power cells into the large amount of useful power for the spacecrafts. The proposed system has the attractive features of simple structure, easy construction and maintenance, and low cost, because two kinds of parts, ac current sources and m-to-1 transmission line (TL) branch connection parts, are used in the whole system. A method of implementing ac current cells having high output impedance is proposed to improve the power collection efficiency of the whole network system. Simulated results show that that low-pass nominal /spl pi/- or T-circuit with high characteristic impedance, which is used for the voltage source to current source converter in the current cell, improves the efficiency of the voltage inverter, filters out the harmonics, and increases the output impedance of the whole current cell.     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Robust fuzzy controlled photovoltaic power inverter with Taguchi method

This paper presents design and implementation of a robust fuzzy controlled photovoltaic (PV) power inverter with Taguchi tuned scaling factors. To achieve fast transient response, small steady-state error and system robustness, a robust fuzzy controller is adopted, in which its input and output scaling factors are determined efficiently by using the Taguchi-tuning algorithm. The proposed system can operate in different modes, grid-connection mode and stand-alone mode, and can accommodate wide load variations. Simulation results and hardware measurements obtained from a prototype with a microcontroller (Intel 80196KC) are presented to verify the theoretical discussions, and its adaptivity, robustness and feasibility.     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

基于预测电流控制的光伏并网系统最大功率点跟踪算法

针对光伏发电的突变性及昼发夜停特性提出一种新型的基于预测电流控制的光伏并网系统最大功率点跟踪(MPPT)算法。根据实际情况考虑光伏阵列的非线性特性,最大功率点周围光伏电压的振荡及逆变器、滤波器的设计等。为了确保系统采用控制算法的稳定性,MPPT的设计应运而生,在此基础上通过改进算法从光伏系统的电压与电流预测基准电流进而控制光伏并网系统。通过与传统的波动相关控制方法对比给出了仿真结果。仿真结果表明:在光照发生突变时,与传统的波动相关控制法相比,提出的改进算法的跟踪速度较之提升9.3%,并能够准确跟踪光伏并网系统最大功率点,且性能稳定可靠。     

Single-phase grid-connected PV system using three-arm rectifier-inverter

A grid-connected photovoltaic (PV) power supply system with on-line voltage regulation capability is presented. It employs the three-arm rectifier-inverter topology with PV modules connected directly on the dc-link. The common-arm is with line-frequency switching and synchronous to the input voltage, aiming for a lower switching loss and decoupling the control of rectifier and inverter portions. As a result, the rectifier and inverter portions can be controlled independently with the rectifier-arm and inverter-arm, respectively. For maximum power point tracking (MPFF) of the PV modules and balancing the power among utility, PV, and the load, a variable dc-link voltage is adopted and controlled by the rectifier-arm based on the MPPT control algorithm. The inverter-arm then regulates the load voltage with good regulation and low distortion. Due to large variation of the dc-link voltage, a feedforward plus feedback control technique with variable gain is developed to keep constant bandwidth of the current loop at any operation condition. Therefore, the performance of the rectifier and inverter portions can be ensured. A system containing a 2 kVA converter and a 1.2 kW PV module is set up, and some experimental results are provided for demonstrating the effectiveness of the proposed method.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

Novel single-stage half-bridge series-resonant buck-boost inverter

A novel single-stage half-bridge series-resonant buck-boost inverter (HB-SRBBI) is proposed. The main attribute of the novel inverter topology is the fact that it generates an ac output voltage larger or lower than the dc input one, depending on the instantaneous duty cycle. This property is not found in the classical voltage source inverter (VST), which produces an ac output instantaneous voltage always lower than the dc input voltage. The proposed inverter circuit topology provides the main switch for turn-on at zero-current-switching (ZCS) by an auxiliary resonant cell built before the output choke. A state-space averaging approach is employed to analyze the system. A design example of 500 W ac/dc inverter is examined to assess the inverter performance and it provides high power efficiency above 90.7% under the rated power.     

AC/DC converter topologies for the Space Station

A new class of AC/DC converter topologies (Type-1 converters) is described, suitable for use in an advanced single-phase sine-wave voltage, high-frequency power distribution system, of the type that was proposed for a 20 kHz Space Station primary electrical power distribution system. The converter comprises a transformer, a resonant network, a current controller, a diode rectifier, and an output filter. The input AC voltage source is converted into a sinusoidal current source using the resonant network. The output of this current source is rectified by the diode rectifier and is controlled by the current controller. The controlled rectified current is then filtered by the output filter to obtain a constant voltage across the load. Three distinct converter topologies, Type-1A, Type-1B, and Type 1-C, are described, and their performance characteristics are presented. All three types have a close-to-unity rated power factor (greater than 0.98), low total harmonic distortion in input current (less than 5%), and high conversion efficiency (greater than 96%)     

Resonant inverters for photovoltaic array to utility interface

A number of high-frequency link power converter schemes suitable for interconnecting a photovoltaic (PV) array to the utility line using resonant inverters are presented. Use of high-frequency resonant inverters (HFRI) results in reduced size, weight and cost. Scheme 1 uses the HFRI-cycloconverter, scheme 2 uses the HFRI-rectifier pulsewidth-modulated voltage source inverter, scheme 3 uses the HFRI-rectifier line commutated inverter working with a fixed maximum possible inverting fringe angle, and scheme 4 uses the HFRI-rectifier line-connected inverter (with line current modulation). These schemes are compared. Based on the comparison, scheme 3 was selected for an initial study. To overcome various problems associated with scheme 3, the line current is modulated sinusoidally in scheme 4. In this scheme, the HFRI is controlled appropriately to obtain a rectified sine wave of 120 Hz in the DC link and the function of the line-connected inverter is to unfold this waveform on alternate half cycles to obtain a sinusoidal line current with the line voltage. Methods of commutation of the line connected inverter are explained. Experimental results obtained with scheme 4 are presented     

Z源NPC三电平变换器恒功率并网控制策略研究

Z源中点钳位式(NPC)三电平变换器把逆变和升压两种环节结合在一起,结构简单、工作效率高,但是针对这种结构输出的无功功率研究较少。提出了一种Z源NPC三电平变换器的恒功率并网控制策略。首先对这种变换器的结构及原理进行分析；再把恒功率控制引入到这种变换器的并网控制中,并采用空间矢量脉宽调制(SVPWM)实现了变换器的并网控制。MATLAB/Simulink软件仿真结果证明了这种变换器能够提高电压升压比。该控制策略可使变换器输出的有功功率、无功功率稳定于设定值,且并网电流谐波较低。     

一种单相光伏并网逆变器改进预测电流控制算法

光伏并网逆变器传统预测电流控制算法由于采样与计算延时会造成差一拍控制,使得逆变器并网电流不能很好地跟踪目标电流,同时逆变器滤波电感模型值与实际值有误差时会造成并网电流谐波大,还可能导致系统不稳定。为克服这些不足,提出了一种改进的预测电流控制方法,可提前一个采样周期对并网逆变器输出电压进行预测,同时利用递推最小二乘法对电感参数进行在线辩识。仿真和试验结果表明所提方法有效提高了逆变器并网电流对目标电流的跟踪精度,减小了并网电流的谐波分量,提高了由逆变器进网的电能的质量。     

Investigation of MHD power generation with supersonic non-equilibrium RF discharge

Magnetohydrodynamic (MHD) power generation with supersonic non-equilibrium plasma is demonstrated. Capacitively coupled radio frequency (RF) discharge (6 MHz, maximum continual power output of 200 W) was adopted to ionize the Mach number 3.5 (650 m/s), 0.023 kg/m3 airflow. In a MHD channel of 16 mm × 10 mm × 20 mm, MHD open voltage of 10 V is realized in the magnetic field of 1.25 T, and power of 0.12 mW is extracted steadily and con-tinuously in the magnetic field of 1 T. The reasons for limited power generation are proposed as:low conductivity of RF discharge; large touch resistance between MHD electrode and plasma;strong current eddies due to flow boundary layer. In addition, the cathode voltage fall is too low to have obvious effects on MHD power generation.     

Stepped Sinewave Inverter

A stepped sinewave dc/ac inverter was analyzed for an inductive load with respect to load current and voltage, harmonics, power factor, and efficiency. This special inverter of high efficiency and low harmonic content is constructed by synthesizing the sinusoidal output by discrete voltage sources, such as storage batteries, solar cell, etc., with electronic switching of the sources at specific time intervals. The switching times are determined for the condition of minimum distortion of the synthesized wave. A 50 W inverter was built and tested to demonstrate this approach.     

Evaluation of active hybrid fuel cell/battery power sources

Hybrid fuel cell/battery power sources have potentially widespread uses in applications wherein the power demand is impulsive rather than constant. Interposing a dc/dc converter between a fuel cell and a battery can create two configurations of actively controlled hybrid fuel cell/battery power sources. Those two configurations are compared using both theory and experiment with special attention to the peak power enhancement, and power losses in the converter. Both of the defined configurations were built, using a 35 W polymer electrolyte membrane (PEM) fuel cell, an 8-cell lithium-ion battery pack, and a high-efficiency power converter. Both two configurations yielded a peak power output of 135 W, about 4 times as high as the fuel cell alone could supply, with only a slight (13%) increase of weight. The converter losses were quantitatively analyzed. Which of the two configurations yields a smaller loss depends on the load power demand characteristics including peak power and load duty ratio. The study results provide guidance for the design of hybrid sources according to the particular load power requirements.     

First Mars outpost power systems

Research into potential power systems for the First Mars Outpost (FMO) was performed. The author examined a representative mission architecture which was developed by NASA to determine power system requirements. Power system options including nuclear, isotope, photovoltaic (PV), chemical heat engine, and regenerative fuel cell (RFC) concepts were identified for potential Mars surface applications. A top-level characterization study was conducted to determine power system mass and area for each application. It is seen that PV systems are generally not suited for Mars surface applications due to the large surface area required and higher mass than a closed Brayton cycle SP100 reactor system. A reactor is currently being considered by NASA Lewis Research Center to provide power for base architectures including an ISRU (in situ resource utilization). An oxygen/methane powered heat engine would provide 40 kWe of emergency power for the habitat. A dynamic isotope power system (DIPS) is the current choice for a long-duration pressurized rover due to the excessive size of a PV/RFC system and higher mass of a heat engine system. DIPS has advantages for other low power systems due to its neatly immediate availability and flexibility (night or day power; no recharging required)     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Implementation of a single-phase AC/AC converter based on neutral-point-clamped topology

A single-phase ac/ac converter based on neutral-point-clamped scheme is proposed to perform unity input power factor and to provide a stable ac voltage to the critical loads. The ac/dc rectifier part is controlled to generate a unipolar pulsewidth modulation (PWM) waveform on the ac terminal by using four power switches with voltage stress of half the dc-link voltage. The carrier-based current control scheme is employed in the inner control loop to track the line current command. To regulate the dc bus voltage, a proportional-integral (PI) control is adopted in the outer control loop. The dc/ac inverter part of the system with four power switches is employed to generate a stable and clean sinusoidal output voltage to the critical load. The instantaneous current control scheme is used to track the output voltage command. To verify the effectiveness of the proposed control algorithm, the simulation and experimental results based on a laboratory prototype were implemented and discussed.     

一种具有电压支撑功能的改进无功注入策略

电压跌落是输配电系统面临的最严重的问题之一。随着分布式光伏电源在电力系统中的渗透率越来越高,国内外最新标准要求光伏逆变器必须具备低电压穿越能力。为了消除有功功率振荡,在传统的正/负序控制基础上提出了一种改进的有功/无功注入策略；针对现有电压支撑方法缺乏电压抬升范围控制,将三相电压幅值作为控制目标,详细推导了适用于不同电压跌落情况下的数学模型,得出为保证各相电压均保持在安全运行范围之内所需注入无功功率参考值。仿真结果验证了所提策略的正确性和有效性。