宇航用小型化超稳晶振（USO）设计与实现

在分析高稳定晶体振荡器(OCXO)工作原理的基础上,提出了一种改善晶体振荡器相位噪声的方法.通过低噪声主振电路设计、高精度控温电路设计及机电一体化设计等措施,设计研制了一种宇航用小型化超稳定晶体振荡器(USO),尺寸为99mm×88mm×55mm.经测试,产品短期频率稳定度为2.11×10-13/1s、3.28×10-13/10s、8.61×10-13/100s(Allan方差),相位噪声为-129.4dBc/Hz@1Hz和-147.0dBc/Hz@10Hz.     

基于梳状谱发生器的毫米波相参脉压模拟器

研制了一种基于梳状谱发生器的全相参脉冲压缩毫米波雷达目标射频回波模拟器。通过与被测雷达共用基准频率参考信号,结合梳状谱发生器及DDS,保证了输出信号和雷达发射信号的相参性和快速频率跳变,实现较好的相位噪声性能和杂散抑制。该系统输出为Ka波段,带宽2GHz,步进100kHz,相位噪声小于一80dBc@1kHz,跳频时间小于2μs。     

一种低噪声和高精度的频率合成技术

介绍了锁相环(PLL)技术和直接数字式频率合成(DDS)技术的基本工作原理,给出了一种提高DDS输出频率精度及减小其相位截断误差的方法。     

用于非线性有源天线的耦合锁相环特性分析

为实现非线性有源天线阵波束扫描,研究了互耦锁相环(PLL)的基本特性。通过对互耦PLL的相位动力学方程的稳定性进行分析,建立了具有延时的阵列模型;通过调节环路延时,互耦PLL不同的非线性动力学特性;采用四单元的耦合锁相环阵列实验电路对理论分析进行了验证,从而提出了在设计基于耦合锁相环的非线性有源天线时,必须对环路延时进行控制,防止环路出现振荡和混沌现象。     

基于DDS+PLL的光源调制与功率稳定控制方法CSCD

量子传感器是基于量子操控技术的研究成果,一般具有高精度、小体积等优势。激光器是量子传感器的核心部件,有抽运和检测功能,激光器的稳定性对量子传感器具有重要的意义。提出了一种直接数字合成法(DDS)与锁相回路(PLL)相结合的方法,对激光器进行调制并抑制调制噪声,实现了激光器的稳定输出。基于现有小型量子传感器装置,在DDS生成4kHz参考信号的情况下实现了激光器电流8kHz调制,抑制了调制时调制电流信号噪声约8dB,并提高了激光器输出光功率的稳定性。     

基于DDS驱动PLL结构的X波段雷达信号频率综合器

给出了一种基于DDS驱动PLL的频率综合器结构。该结构采用AD9854DDS芯片产生低频的参考信号,然后驱动锁相环和VCO产生X波段射频信号。实验和测量结果表明,该频率综合器具有较宽的工作带宽和较低的相位噪声,可以用来产生连续波、线性调频信号和频率捷变信号用于X波段雷达信号的仿真。     

S频段小数分频锁相环频率合成器实现与应用

传统的整数分频锁相环频率合成技术无法在单个环路实现高频率、低分辨率和低相噪的目标,小数分频锁相环在提高鉴相频率的同时减小分频计数值,从而降低相位噪声。针对USB统一测控系统的需要,本文提出基于单片小数分频锁相环的微波频率合成方法。实验结果表明,小数分频锁相环频率合成器具备良好的信号输出特性,可以为测控系统提供低成本频率合成方案。     

用于RFOG的光学锁相环仿真研究

谐振式光纤陀螺是实现光纤陀螺小型化发展的重要方向,具有广阔的应用背景和很好的应用前景。而激光器作为谐振式光纤陀螺的关键设备之一,其性能直接影响着谐振式光纤陀螺的精度。为了解决谐振式光学陀螺的背反噪声问题,采用光学锁相环技术对激光器频率进行锁定的方案,通过对光学锁相环进行建模、仿真分析,重点研究了锁相原理及锁相方案,验证了基于电流调制的半导体激光器的光学锁相环可行性。最终验证了光学锁相环的相位锁定效果,实现了两激光器输出频率差值稳定的设计目标。     

无人机高速DS/FH混合扩频通信系统关键模块设计

针对UAV(Unmanned Aerial Vehicle,无人机)测控链路高抗干扰需求,给出了实现跳频速率20 000次/s的扩跳混合无人机测控数据链系统实现方案.系统采用跳频频率并行捕获模式.跳频源设计采用直接频率合成、DDS(Direct Digital Synthesis,直接数字频率合成)和PLL (Phase-Locked Loop,锁相环)相结合的混合频率合成技术.利用相位响应滤波器,通过正交调制技术完成MSK(Minimum Shift Keying,最小频移键控)、GMSK (GaussianMinimum Shift Keying,高斯最小频移键控)调制.通过推导得出2 bit差分解调输出与载波频率选择有关,且为四分之数据率的整数倍关系.然后通过实例分析给出了跳频频率间隔选取方法,即跳频间隔应当将临近跳频的主瓣分开,同时跳频载波频率应当设在其他跳频频谱的零点处.最后总结了高速扩跳频系统参数设计一般步骤.     

双绕组感应发电机静止励磁调节器的锁相环研究

双绕组感应发电机具有随负载变化调节励磁磁场、保持负载电压恒定不变的优点,通过静止励磁调节器输出的有功电流控制母线电压、无功电流控制负载电压,两者经过坐标变换形成反馈电流,实现系统的闭环控制。锁相环(PLL)为坐标变换提供相位信息,选用合适的PLL可以提高坐标变换的动静态性能,为控制系统提供快速准确的反馈信息。分析了双绕组感应发电机励磁电压的特点,分析了双dq变换PLL、延时信号对消PLL、基于延时信号对消的滑动平均滤波PLL的各自工作特点,最后优选了基于延时信号对消的滑动平均PLL检测励磁电压相位。     

一种宽带高速跳频载波频综结构的设计

将DDS（直接数字合成）与PLL（锁相环）频率合成技术相结合,采用多环并列流水线结构,设计出混合扩/跳频系统的载波频率综合单元。利用DDS技术可实现频率分辨率高、转换时间快等要求,利用PLL技术可实现杂散抑制性能高、扩展宽带等要求,并采用多环并列硬件结构保证了系统的跳变速度和宽频带指标。经闭环测试平台的测试,系统达到350～1800MHz带宽可变,频率跳变速度10 000跳/s可变,杂散抑制优于-80dBc。文章首先给出详细的硬件设计方案及其实现,同时理论分析了个各项指标的优化,最后给出闭环测试平台的搭建以及最终测试结果。     

外涵偏轴分开排气喷管的流场和声场数值计算

以某型涡扇发动机为原型,建立了1/10缩比的分开排气式涡扇发动机排气喷管物理模型,采用大涡模拟(LES)计算了不同外涵偏轴距离的排气喷管非稳态流场,利用FW-H(Ffows Williams-Hawkings)声学模型和傅里叶变换得到了排气喷流噪声声压级空间分布特征.计算结果表明:外涵偏轴式分开排气喷管有抑制排气喷流噪声的作用.喷流噪声整体抑制效果与偏轴距离有关,在偏轴距离为0.15D时,排气喷管下方的噪声降低达到最大,且排气噪声峰值由原型的146.7dB降低到139.5dB,降低了7.2dB.研究的排气结构和数值计算方法可作为分开排气式涡扇发动机降噪设计的参考.      

Low C/N_0 Carrier Tracking Loop Based on Optimal Estimation Algorithm in GPS Software Receivers

Suppressing jitter noises in a phase locked loop(PLL) is of great importance in order to keep precise and continuous track of global positioning system(GPS) signals characterized by low carrier-to-noise ratio(C/N0).This article proposes and analyzes an improved Kalman-filter-based PLL to process weak carrier signals in GPS software receivers.After reviewing the optimal-bandwidth-based traditional second-order PLL,a Kalman-filter-based estimation algorithm is implemented for the new PLL by decorrelating the model error noises and the measurement noises.Finally,the efficiency of this new Kalman-filter-based PLL is verified by experimental data.Compared to the traditional second-order PLL,this new PLL is in position to make correct estimation of the carrier phase differences and Doppler shifts with less overshoots and noise disturbances and keeps an effective check on the disturbances out of jitter noises in PLL.The results show that during processing normal signals,this improved PLL reduces the standard deviation from 0.010 69 cycle to 0.007 63 cycle,and for weak signal processing,the phase jitter range and the Doppler shifts can be controlled within ±17° and ±5Hz as against ±25° and ±15 Hz by the traditional PLL.     

一种球墨铸铁的超高周疲劳行为研究

 应用超声疲劳试验技术,完成了20kHz频率下(R=-1,R=0 1)的疲劳试验,获得球墨铸铁GS51在亿周次范围内的疲劳性能。通过20kHz频率下的超声疲劳试验和35Hz频率下的常规疲劳试验,确定了球墨铸铁GS51在104～1010周的S N曲线,并对105～107周之间2种频率下的试验结果进行了比较。试验结果表明,在疲劳循环大于107周时,试件仍会发生疲劳断裂;在107～1010周之间,疲劳强度随着循环次数的增加而下降。比较107周内20kHz和35Hz下的试验结果,表明超声疲劳试验中,频率对球墨铸铁GS51疲劳性能的影响不大。经扫描电镜观察疲劳断裂试件发现,在高周疲劳条件下,疲劳破坏主要源于试件表面不均匀分布的球墨和试件内部的缩孔。     

带通限幅器对锁相环噪声性能的影响

锁相环路中,在鉴相器前加上AGC（自动增益控制）,可以使环路性能在输入信噪比发生变化时保持稳定,带通限幅器也可以起到类似作用。尽管有一些文章对限幅器的性能作了研究,但是在PLL（锁相环）闭环条件下,鲜有文章分析其对环路噪声性能的影响。因此,文章以基本PLL环路的数学模型为基础,推导出PLL中分别加入相干AGC和带通限幅器后新的环路数学模型,以一阶PLL为例,计算和比较不同控制方式下环路相位误差均方值的变化,最后说明应当根据飞行任务的不同选择对环路更有利的控制方式。     

一种低复杂度的极低信噪比高动态信号载波粗捕获算法

 针对传统的时域匹配平均周期图算法计算复杂度高的问题,对极低信噪比高动态信号的载波粗捕获算法进行了研究,提出了一种改进的带有补零的频域移位平均周期图算法。该算法采用多速率频域移位运算简化了多支路多普勒变化率匹配,与原算法相比,其计算复杂度降低倍数为匹配支路数与补零倍数之比,捕获性能几乎不损失。给出了算法中影响捕获性能与计算复杂度的关键参数设计方法。在信噪比(SNR)为－41 dB(载噪比C/N₀=18 dBHz)、载波多普勒频偏为－300～300 kHz、多普勒变化率为－800～800 Hz/s、码速率为20 bps条件下对两种算法进行了仿真,结果表明在基本满足后级载波跟踪需求条件下,即频偏精度均达±12 Hz时,多普勒变化率精度均达±25 Hz/s,捕获概率都在90%以上时,改进算法捕获时间比原算法增加了8%,计算复杂度降低了70%。     

Imperfect Carrier Recovery Effect on Filtered PSK Signals

Coherent demodulation of a PSK signal requires the generation of a local carrier phase reference. Methods are given to determine the detection loss caused by noisy phase recovery and its use in the coherent detection of filtered BPSK and QPSK signals. It is assumed that the phase noise can have a static part and a random component with a Tikhonov-type distribution. The static part is mostly due to offset frequency tracking of the PLL used to recover the carrier, while the random component is due to thermal noise present in the carrier recovery loop and is also due to the random nature of the phase modulation. It is shown that the probability of error of BPSK and QPSK can be expressed as a finite sum of a set of strictly alternating converging series when the number of ISI terms is finite. Upper and lower bounds on the probability of error have been derived when this number becomes infinite and we show how this error rate can be computed with any desired accuracy. Numerical results are presented for various values of static error and phase noise variance when the transmit and receive filters are 4-pole Butterworth filters. For filtered PSK signals and for a bit error rate of 10-6, our results show that the additional degradation in presentday receiver systems due to imperfect carrier recovery can be less than 0.1 dB for BPSK and less than 1 dB for QPSK.     

Carrier loop architectures for tracking weak GPS signals

The performance of various carrier recovery loop architectures (phase lock loop (PLL), Doppler-aided PLL, frequency lock loop (FLL), and Doppler-aided FLL) in tracking weak GPS signals are analyzed and experimentally validated. The effects of phase or frequency detector design, oscillator quality, coherent averaging time, and external Doppler aiding information on delaying loss of lock are quantified. It is shown that for PLLs the metric of total phase jitter is a reliable metric for assessing low C/N performance of the tracking loop provided the loop bandwidth is not too small (~> 5 Hz). For loop bandwidths that are not too small, total phase jitter accurately predicts carrier-to-noise ratio (C/N) at which loss of lock occurs. This predicted C/N is very close to the C/N predicted by bit error rate (BER). However, unlike BER, total phase jitter can be computed in real-time and an estimator for it is developed and experimentally validated. Total phase jitter is not a replacement for BER, since at low bandwidths it is less accurate than BER in that the receiver loses lock at a higher C/N than predicted by the estimator. Similarly, for FLLs operating at small loop bandwidths, it is found that normalized total frequency jitter is not a reliable metric for assessing loss of lock in weak signal or low C/N conditions. At small loop bandwidths, while total frequency jitter may indicate that a loop is still tracking, the Doppler estimates provided by the FLL will be biased.