Design of Switching Regulator with Combined FM and On-Off Control

The design and implementation of a switching regulator incorporating a high-frequency series-resonant converter and a combined FM and on-off feedback control is presented. The combined FM and on-off control results in a better conversion efficiency and a wider range of operational input voltage and output current. A 22.5 V, 50 W experimental regulator has been built to demonstrate the practicality of the circuit and its high efficiency, typically 92 to 96 percent, depending on the input and loading conditions.     

A Novel Feedforward Compensation Canceling Input Filter-Regulator I nteraction

The interaction between the input filter and the control loop of switching regulators often results in detrimental effects, such as loop instability, degradation of transient response, and audiosusceptibility, etc. The concept of pole-zero cancellation is employed to mitigate some of these detrimental effects and is implemented using a novel feedforward loop, in addition to existing feedback loops of a buck regulator. Experimental results are presented which show excellent correlation with theory.     

Stability Analysis of a Buck Regulator Employing Input Filter Compensation

The interaction between the input filter and the regulator often causes serious degradation of performance. The reduction in loop gain due to input filter interaction can result in system instability. An exact stability analysis of the buck regulator system is presented. The input filter parameter values are varied and system instability is predicted for the case without feedforward. The eigenvalues of the system can be brought back into the unit circle and the system thus stabilized with the addition of the feedforward loop. Measurements made for the cases with and without feedforward confirm the analytical prediction.     

Input-Filter Design for Switching Regulators

The interaction between the input filter and the control loop of switching regulators often results in detrimental effects, such as loop instability, transient response, and audio-signal-rejection rate, etc. A small-signal average model is derived to investigate these effects. Design constraints of an input-filter and switching-regulator system are formulated. An optimum low-pass and light-weight filter configuration is proposed.     

Capacitive-loaded push-pull parallel-resonant converter

Results of a theoretical and experimental investigation of a capacitive-loaded push-pull parallel-resonant DC-DC converter (CL-PPRC) are presented and discussed. The push-pull parallel-resonant converter (PPRC) is driven by a lower-than-resonance frequency and the secondary voltage is rectified and smoothed by a capacitive filter. The CL-PPRC is shown to operate in the zero voltage switching (ZVS) mode with a boost-like DC transfer ratio that is approximately linear with the period of the switching frequency. Experimental results of a 180 W, high output voltage (1.8 KV) prototype are found to be in good agreement with the analysis, models, and simulation results presented. The basic characteristic of ZVS, the fact that the resonant current is passing through the switches only during a fraction of the period, the high-voltage transfer ratio, and the inherent input/output (I/O) isolation, make the proposed topology a viable design alternative in avionic and aerospace applications     

Describing Function Properties of a Magnetic Pulsewidth Modulator

An analysis is presented for the transfer functions of a particular pulsewidth modulator and power-stage subsystem that has been widely used in practical switching-mode dc regulator systems. The switch and filter are in a ?buck? configuration, and the switch is driven by a constant-frequency, variable duty-ratio, push-pull magnetic modulator employing square-loop cores. The two transfer functions considered are that with modulator control signal as input and that with line voltage as input. For ac signal,the corresponding describing functions (DF) are derived. It is shown thatcurrent-source drive to the modulator extends the control DF frequency response over that with voltage drive, and that complete cancellation of the effects of line variations can be obtained at dc, but not for ac. Experimental confirmation of the analytical results for the control DF are presented.     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

高速磁悬浮电动机变频器用开关电源设计

采用基于NCP1200的电流型控制,设计并研制了应用于高速磁悬浮电动机变频器的开关电源,该电源自适应输入电压波动,并自动调节PWM占空比以保证输出电压恒定.实验结果表明,该电源具有输出纹波小、效率高、EMI小、电压调整率和稳压性能好等优点,可用作变频器控制电路的电源.     

LLC parallel resonant converter design by scaling the LC converter

An efficient and practical method for steady-state design of an LLC-type parallel resonant dc/dc converter (LLC-PRC) is presented. In general, the output characteristic curves of LLC-PRC can be obtained by multiplying the output curves of the LC-type parallel resonant converter (LC-PRC) by a ratio of the parallel and series inductances. The peak voltage and current stresses on the resonant elements also depend on the same ratio. The LLC-PRC with a filter inductor is examined for two conduction modes, continuous and discontinuous capacitor voltage conduction modes, to show the effect of the inductance ratio. A means to use the derived equations to obtain the zero current switching (ZCS) is given. Also, a design procedure, along with design examples, is given to illustrate the use of the equations and characteristic curves. An experimental LLC-PRC is built to ensure the validity of the equations and design examples     

Fourier theory of jumps applied to converter harmonic analysis

The Fourier theory of jumps (FTJ) is demonstrated as an aid in deriving closed-form analytical equations for converter switching harmonics. The switching waveforms analyzed are the input current and output voltage and current of a three-phase, ac-dc, step-down, dead-band pulsewidth modulated (PWM), unity power factor converter. The input current closed-form harmonic equation is derived for two parallel-connected, interleaved-PWM converters supplying the same load and sharing a common input filter. The equations are compared with PSpice^TM simulations and practical results     

An Adaptive-Control Switching Buck Regulator-Implementation, Analysis, and Design

Describing-function techniques and averaging methods have been employed to characterize a multiloop switching buck regulator by three functionsl blocks: power stage, analog signal processor, and pulse modulator. The model is employed. to explore possible forms of pole-zero cancellation and the adaptive nature of the control to filter parameter changes. Analysis-based design guide lines are provided including a suggested additional RC-compensation loop to optimize regulator performances such as stability, audiosusceptibility, output impedance, and load transient response.     

Zero dynamics-based design of damping networks for switching converters

A new design technique of the input filter damping network for dc-to-dc switching converters of buck type is presented. This technique is derived by means of zero dynamics analysis of the switching converter and yields equivalent results to those obtained using the classical approach based on minimizing the filter output impedance. The new method can be applied in converters of buck type with two inductors, boost with two inductors and dual SEPIC. Simulation and experimental results corresponding to a boost converter with two inductors illustrate the procedure.     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

A Closely Regulated TWT Converter

The design concept for the traveling wave tube amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics were utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power traveling wave tube (TWT), and at the same time operate at an efficiency of better than 90 percent from a 30-volt source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data is presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered. The circuit provides better than 0.5 percent regulation against load change, input voltage change, and over-operating temperature range of from -20 to + 80°C, with output ripple voltage of less than 2 volts peak-to-peak on top of the 3600-Vdc output. The measured efficiency was typically 87 percent. and recommendations are included to improve this to in excess of 90 percent.     

A fixed frequency LCL-Type series resonant converter

A fixed frequency LCL-type series resonant converter (SRC) which uses an inductive output filter is proposed. Steady-state analysis of the converter is presented using complex ac circuit analysis. Based on the analysis, a simple design procedure is given. Detailed space integrated control experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load and supply voltage conditions. Also, detailed experimental results obtained from a metal-oxide-semiconductor field-effect transistor (MOSFET) based 500 W converter are presented to verify the analysis and SPICE simulation results. The results obtained from the analysis, SPICE simulation and the experimental converter are compared. The proposed converter requires a narrow variation in pulsewidth while maintaining lagging power factor mode of operation for a very wide variation in the load as well as supply voltage     

On Lyapunov stability analyses of the switching regulator/filtersystem

The stability design criteria for the fourth-order switching regulator/low-pass filter system are obtained directly from the solution to the resultant simultaneous equations for the Lyapunov matrix equation. The regulator/filter system is asymptotically stable if the values of the filter components are chosen to satisfy the derived Lyapunov stability design criterion for a given value of the switcher dynamic resistance     

Optimum Design of RC Snubbers for Switching Regulators

The optimum design of an RC snubber to suppress the surge voltage across the transistor in a switching regulator with a two-winding reactor is presented. Analyzing the surge voltage by means of high-frequency equivalent circuits, we obtain the third-order characteristic equation. This third-order equation is first analyzed by the aid of the root locus method. As a result, the region where the surge voltage can be suppressed is described in the R-C plane. Then considering the snubber loss, the optimum resistance and capacitance can be obtained. Second, the precise design procedure of RC snubbers is discussed by normalization and numerical calculations. This procedure is summarized in easy-to-use nomographs.     

基于Kalman滤波的GPS/INS接收机自适应干扰抑制方法

 考虑到惯导信息辅助GPS(GPS/INS)接收机对干扰抑制实时性的要求,提出一种基于Kalman滤波的GPS/INS接收机自适应干扰抑制方法。自适应广义旁瓣相消(GSC)多采用低复杂度最小均方(LMS)算法更新权矢量,收敛速率较低,严重时会导致接收机定位中断。首先利用Householder变换构建GSC下支路的阻塞矩阵,用于阻塞任意二维阵型阵列接收的期望信号;再用Kalman滤波自适应更新下支路权矢量,从而有效提高阵列输出信干噪比(SINR)。理论分析和仿真结果说明本文方法可有效抑制干扰对接收机的影响,且具有实时性高的特点。     

小型无人机发电系统的研制

本文介绍了一种适用于无人机的专用电源系统的设计方案,该方案由永磁同步发电机和宽电压输入范围的电源变换/调节装置组成.该方案具有系统结构简单、可靠性高、电源品质高和转速范围宽的优点,并对电源系统进行了实验验证,实验结果和理论分析一致.     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented