Surface integrity and fatigue behavior when turning γ-TiAl alloy with optimized PVD-coated carbide inserts

This paper presents a comprehensive investigation on the effects of tool and turning parameters on surface integrity and fatigue behavior in turning c-Ti Al alloy. The wear of inserts surface, cutting forces, and surface roughness were studied to optimize PVD-coated carbide inserts.Surface topography, residual stresses, microhardness, and microstructure were analyzed to characterize the surfaces layer under different turning parameters. Surface integrity and fatigue life tests of c-Ti Al alloy were conducted under turning and turning-polishing processes. The results show that compared to CNMG120412-MF4, CNMG120408-SM is more suitable because it obtained low cutting force, surface roughness, and tool wear. With increasing the cutting speed and depth, the depths of the compressive residual stress layer, hardening layer, and plastic deformation layer increased. For turning and turning-polishing specimens, the compressive residual stress was relaxed by less than 20%–30% after 10~7 cycles. The fatigue life of a turning-polishing specimen with R_a= 0.15 mm has increased 3 times from that of a turning specimen with R_a= 0.43 mm.     

Effects of different aging treatments on microstructures and mechanical properties of Al-Cu-Li alloy joints welded by electron beam welding

Post-weld single aging treatment(solution treatment at 510 ℃ for 1 h, water quenching,and aging at 155 ℃ for 16 h) and post-weld double aging treatment(solution treatment at 510 ℃ for 1 h, water quenching, aging at 155 ℃ for 16 h, and aging at 130 ℃ for 12 h) are carried out on Al-Cu-Li alloy joints by electron beam welding(EBW) respectively. The effects of aging treatments on microstructures and mechanical properties of welded joints are investigated. Results show that the mechanical properties of welded joints are obviously improved after both aging treatments. The strength coefficient of joints is increased from 0.64 in an as-welded condition(AW) to 0.90 after post-weld double aging treatment. Microstructure analysis shows that the precipitates of the fusion zone within grains and grain boundaries are less in the AW condition. After post-weld heat treatment(PWHT), a lot of fine needle-like phases T_1(Al_2 Cu Li) precipitate in grain boundaries of the fusion zone, and more horseshoe-shaped β' (Al_3 Zr) particles precipitate within grains. In addition,grains of the fusion zone are refined after post-weld double aging treatment, which leads to an effect of grain refinement strengthening. Consequently, the mechanical properties of welded joints are greatly improved.     

Testing and evaluation for fatigue crack propagation of Ti-6Al-4V/ELI and 7050-T7452 alloys at high temperatures

This paper seeks to evaluate crack propagation properties and residual lives of metallic alloys subjected to fatigue loading at room and high temperatures. Fatigue crack growth tests were performed on Ti-6Al-4V/ELI and 7050-T7452 subjected to constant-amplitude and actual randomspectra loading at room temperature of about 25 ℃ and at high temperatures of 250 ℃ and 150 ℃ to determine their crack growth properties and residual lives. The damage mode and mechanisms at high temperature were compared with those at room temperature on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectra load history were evaluated based on a modified accumulation damage rule accounting for the load interaction.Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.     

非线性不平衡转子轴承系统周期解的预测

本文提出一种对非线性不平衡转子轴承系统周期解进行预测的新型算法,它利用系统周期解的稳态及瞬态信息,反解雅可比矩阵,实现对系统周期解的预测追踪,并利用反解得出的雅可比矩阵,求得系统周期解的Floquet乘子以判别其非线性稳定性。文中以刚性不平衡转子轴承系统为例,实现了周期解的预测追踪及非线性稳定性判别,说明了新算法的有效性。      

Tangling and instability effect analysis of initial in-plane/out-of-plane angles on electrodynamic tether deployment under gravity gradient

The space debris occupies the orbit resources greatly, which seriously threats the safety of spacecraft for its high risks of collisions. Many theories about space debris removal have been put forward in recent years. The Electro Dynamic Tether (EDT), which can be deployed under gravity gradient, is considered to be an effective method to remove debris in low orbit for its low power consumption. However, in order to generate sufficient Lorentz force, the EDT needs to be deployed to several kilometers, which increases the risks of tangling and the instability of the EDT system. In the deployment process, different initial in-plane/out-of-plane angles, caused by direction error at initial release or the initial selection of ejection, affect the motion of EDT system seriously. In order to solve these problems, firstly, this paper establishes the dynamic model of the EDT system. Then, based on the model, safety metrics of avoiding tangling and assessing system stability during EDT deployment stage are designed to quantitatively evaluate the EDT system security. Finally, several numerical simulations are established to determine the safety ranges of the initial in-plane/out-of-plane angles on the EDT deployment.     

Springback prediction of thick-walled high-strength titanium tube bending

Significant springback occurs after tube rotary-draw-bending （RDB）, especially for a high-strength Ti-3A1-2.5V tube （HSTT） due to its high ratio of yield strength to Young＇s modulus. The combination scheme of explicit and implicit is preferred to predict the springback. This simulation strategy includes several numerical parameters, such as element type, number of elements through thickness （NEL）, element size, etc. However, the influences of these parameters on spring- back prediction accuracy are not fully understood. Thus, taking the geometrical specification 9.525 mm × 0.508 mm ofa HSTT as the objective, the effects of numerical parameters on prediction accuracy and computation efficiency of springback simulation of HSTT RDB are investigated. The simulated springback results are compared with experimental ones. The main results are： （1） solid and continuum-shell elements predict the experimental results well; （2） for C3DSR elements, NEL of at least 3 is required to obtain reliable results and a relative error of 29% can occur as NEL is varied in the range of 1-3; （3） specifying damping factor typically works well in Abaqus/Emplicit simulation of springback and the springback results are sensitive to the magnitude of damping factor. In addition, the explanations of the effect rules are given and a guideline is added.     

An approach for parameter estimation of combined CPPM and LFM radar signal

In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation (CPPM) and linear frequency modulation (LFM), which can be widely used in electronic countermeasures, is addressed. An approach is proposed to estimate the initial frequency and chirp rate of the combined signal by exploiting the second-order cyclostationarity of the intra-pulse signal. In addition, under the condition of the equal pulse width, the pulse repetition interval (PRI) of the combined signal is predicted using the low-order Volterra adaptive filter. Simulations demonstrate that the proposed cyclic autocorrelation Hough transform (CHT) algorithm is theoretically tolerant to additive white Gaussian noise. When the value of signal noise to ratio (SNR) is less than 4 dB, it can still estimate the intra-pulse parameters well. When SNR = 3 dB, a good prediction of the PRI sequence can be achieved by the Volterra adaptive filter algorithm, even only 100 training samples.     

Brazing of C/C composite and Ti-6Al-4V with graphene strengthened AgCuTi filler: Effects of graphene on wettability,microstructure and mechanical properties

Graphene nanosheets(GNSs) strengthened AgCuTi composite filler(AgCuTi_G) was used to braze C/C composite and Ti-6Al-4V. The effects of GNSs on the wettability of AgCuTi_G filler on the C/C composite surface and the interfacial microstructure and mechanical properties of brazed joints were investigated. The results indicate that the addition of GNSs reduced the wettability of AgCuTi_G. The interfacial microstructure of brazed joints evolved with the addition of GNSs, where Ti_3Cu_4 and TiCu_4 were converted to TiCu and the thickness of the reaction layer adjacent to the base material decreased. The maximum shear strength of joints brazed at 0.3 wt% GNSs was 23.3 MPa(880℃/10 min). Further adding GNSs deteriorated the shear strength of the joints. Fracture of the joints occurred in the C/C composite substrate and the TiC layer adjacent to C/C composite.     

Infrared radiation signature of exhaust plume from solid propellants with different energy characteristics

The infrared radiation signature of the plume from solid propellants with different energy characteristics is not the same. Three kinds of double-base propellants of different energy characteristics are chosen to measure the infrared spectral radiance from 1000 cm 1 to 4500 cm 1 of their plumes. The radiative spectrum is obtained in the tests. The experimental results indicate that the infrared radiation of the plume is determined by the energy characteristics of the propellant. The radiative transfer calculation models of the exhaust plume for the solid propellants are established. By including the chemical reaction source term and the radiation source term into the energy equation, the plume field and the radiative transfer are solved in a coupled way. The calculated results are consistent with the experimental data, so the reliability of the models is confirmed. The temperature distribution and the extent of the afterburning of the plume are distinct for the propellants of different energy characteristics, therefore the plume radiation varies for different propellants. The temperature of the fluid cell in the plume will increase or decrease to some extent by the influence of the radiation term.     

Ignition enhancement of ethylene/air by NOx addition

Recently, non-equilibrium plasma assisted combustion (PAC) has been found to be promising in reducing the ignition delay time in hypersonic propulsion system. NO x produced by non-equilibrium plasma can react with intermediates during the fuel oxidation process and thereby has influence on the combustion process. In this study, the effects of NO x addition on the ignition process of both the homogeneous ethylene/air mixtures and the non-premixed diffusion layer are examined numerically. The detailed chemistry for ethylene oxidization together with the NO x sub-mechanism is included in the simulation. Reaction path analysis and sensitivity analysis are conducted to give a mechanistic interpretation for the ignition enhancement by NO x addition. It is found that for both the homogenous and non-premixed ignition processes at normal and elevated pressures, NO 2 addition has little influence on the ignition delay time while NO addition can significantly promote the ignition process. The ignition enhancement is found to be caused by the promotion in hydroxyl radical production which quickly oxidizes ethylene. The promotion in hydroxyl radical production by NO addition is achieved in two ways:one is the direct production of OH through the reaction HO2+NO = NO2+OH, and the other is the indirect production of OH through the reactions NO+O2=NO2+O and C2H4+O = C2H3+OH. Moreover, it is found that similar to the homogeneous ignition process, the acceleration of the diffusion layer ignition is also controlled by the reaction HO2+NO = NO2+OH.     

Progress in helicopter infrared signature suppression

Due to their low-attitude and relatively low-speed fight profiles, helicopters are subjected to serious threats from radio, infrared(IR), visual, and aural detection and tracking. Among these threats, infrared detection and tracking are regarded as more crucial for the survivability of helicopters. In order to meet the requirements of infrared stealth, several different types of infrared suppressor(IRS) for helicopters have been developed. This paper reviews contemporary developments in this discipline, with particular emphasis on infrared signature suppression, advances in mixer-ejectors and prediction for helicopters. In addition, several remaining challenges, such as advanced IRS, emissivity optimization technique, helicopter infrared characterization, etc., are proposed, as an initial guide and stimulation for future research. In the future, the comprehensive infrared suppression in the 3–5 lm and 8–14 lm bands will doubtfully become the emphasis of helicopter stealth. Multidisciplinary optimization of a complete infrared suppression system deserves further investigation.     

Influences of pre-torsion deformation on microstructure and mechanical properties of pure titanium subjected to subsequent tension deformation

A series of experimental studies was carried out to investigate the influences of pre-torsion on microstructure evolution, mechanical properties, and fracture appearance of pure titanium subjected to subsequent tension deformation. An introduction of pre-torsion strain can improve the materials’ mechanical properties through micro hardness evaluation. That is, the micro hardness of tensile samples with pre-torsion deformation is much higher than that of samples processed by single torsion or tension. It can be seen from the microstructure that pre-torsion deformation can be used to refine grains better and control grains’ morphology by combining subsequent tension. The results indicate that the grains are refined most evidently for tensile samples with 2 turn pre-torsion deformation. Moreover, fracture analysis indicates that tensile samples with pre-torsion strain can present good comprehensive performance. In conclusion, pre-torsion deformation plays an important role in improving comprehensive performance and controlling microstructure evolution on pure titanium subjected to later tension deformation.     

Radical recombination in a hydrocarbon-fueled scramjet nozzle

To reveal the radical recombination process in the scramjet nozzle flow and study the effects of various factors of the recombination, weighted essentially non-oscillatory(WENO)schemes are applied to solve the decoupled two-dimensional Euler equations with chemical reactions to simulate the hydrocarbon-fueled scramjet nozzle flow. The accuracy of the numerical method is verified with the measurements obtained by a shock tunnel experiment. The overall model length is nearly 0.5 m, with inlet static temperatures ranging from 2000 K to 3000 K, inlet static pressures ranging from 75 k Pa to 175 k Pa, and inlet Mach numbers of 2.0 ± 0.4 are involved.The fraction Damkohler number is defined as functions of static temperature and pressure to analyze the radical recombination progresses. Preliminary results indicate that the energy releasing process depends on different chemical reaction processes and species group contributions. In hydrocarbon-fueled scramjet nozzle flow, reactions with H have the greatest contribution during the chemical equilibrium shift. The contrast and analysis of the simulation results show that the radical recombination processes influenced by inflow conditions and nozzle scales are consistent with Damkohler numbers and potential dissociation energy release. The increase of inlet static temperature improves both of them, thus making the chemical non-equilibrium effects on the nozzle performance more significant. While the increase of inlet static pressure improves the former one and reduces the latter, it exerts little influence on the chemical non-equilibrium effects.     

SCC investigation of low alloy ultra-high strength steel 30CrMnSiNi2A in 3.5wt%NaCl solution by slow strain rate technique

To evaluate stress corrosion cracking(SCC) mechanism of low alloy ultra-high strength steel 30CrMnSiNi2 A in environment containing NaCl, SCC behavior of the steel in 3.5wt% NaCl solution is investigated by slow strain rate technique(SSRT) with various strain rates and applied potentials, surface analysis technique, and electrochemical measurements. SCC susceptibility of the steel increases rapidly with strain rate decreasing from 1 · 10 5s 1to 5 · 10 7s 1, and becomes stable when strain rate is lower than 5 · 10 7s 1. SCC propagation of the steel in the solution at open circuit potential(OCP) needs sufficient hydrogen which is supplied at a certain strain rate.Fracture surface at OCP has similar characteristics with that at cathodic polarization 1000 mVSCE, which presents characteristic fractography of hydrogen induced cracking(HIC).All of these indicate that SCC behavior of the steel in the solution at OCP is mainly controlled by HIC rather than anodic dissolution(AD).     

Analytical model of cutting force in axial ultrasonic vibration-assisted milling in-situ TiB2/7050Al PRMMCs

Ultrasonic vibration-assisted milling has been widely applied in machining the difficult-to-cut materials owing to the remarkable improvements in reducing the cutting force. However, analytical models to reveal the mechanism and predict the cutting force of ultrasonic vibration-assisted milling metal matrix composites are still needed to be developed. In this paper, an analytical model of cutting force was established for ultrasonic vibration-assisted milling in-situ TiB₂/7050Al metal matrix composites. During modeling, change of motion of the cutting tool, contact of tool-chip-workpiece and acceleration of the chip caused by ultrasonic vibration was considered based on equivalent oblique cutting model. Meanwhile, material properties, tool geometry, cutting parameters and vibration parameters were taken into consideration. Furthermore, the developed analytical force model was validated with and without ultrasonic vibration milling experiments on in-situ TiB₂/7050Al metal matrix composites. The predicted cutting forces show to be consistent well with the measured cutting forces. Besides, the relative error of instantaneous maximum forces between the predicted and measured data is from 0.4% to 15.1%. The analytical model is significant for cutting force prediction not only in ultrasonic-vibration assisted milling but also in conventional milling in-situ TiB₂/7050Al metal matrix composites, which was proved with general applicability.     

CFRP-TC4叠层板的钻削实验

采用硬质合金麻花钻对CFRP-TC4叠层板进行钻削试验,分析了钛合金层加工参数对钻削力、钻削温度和加工孔质量的影响。结果表明:随着转速的增加,钛合金层的轴向力逐渐减小;随着钛合金层进给量的增加,钛合金层与CFRP层的轴向力之比逐渐增加。运用指数公式模型对钛合金层轴向力实验结果进行回归分析,得到轴向力与转速以及进给量之间的关系式:F_z=2 088n~(-0.1222)·f_r~(0.2016),并对该方程进行了检验验证,误差均小于10%;在钛合金层进给量不变时,随着钛合金层转速的增加,CFRP的最大烧伤环直径和层间最高温度逐渐增加。     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

7YSZ coating prepared by PS-PVD based on heterogeneous nucleation

Plasma spray-physical vapor deposition (PS-PVD) as a novel coating process based on low-pressure plasma spray (LPPS) has been significantly used for thermal barrier coatings (TBCs). A coating can be deposited from liquid splats, nano-sized clusters, and the vapor phase forming different structured coatings, which shows obvious advantages in contrast to conventional technologies like atmospheric plasma spray (APS) and electron beam-physical vapor deposition (EB-PVD). In addition, it can be used to produce thin, dense, and porous ceramic coatings for special applications because of its special characteristics, such as high power, very low pressure, etc. These provide new opportunities to obtain different advanced microstructures, thus to meet the growing requirements of modern functional coatings. In this work, focusing on exploiting the potential of gas-phase deposition from PS-PVD, a series of 7YSZ coating experiments with various process conditions was performed in order to better understand the deposition process in PS-PVD, where coatings were deposited on different substrates including graphite and zirconia. Meanwhile, various substrate temperatures were investigated for the same substrate. As a result, a deposition mechanism of heterogeneous nucleation has been presented showing that surface energy is an important influencing factor for coating structures. Besides, undercooling of the interface between substrate and vapor phase plays an important role in coating structures.     

迷宫密封—滑动轴承—转子系统的非线性动力稳定性

 研究迷宫密封—滑动轴承—转子系统在不平衡量激励下的非线性动力稳定性。存在不平衡量的转子在旋转过程中受到周期激励,低转速时,转子作与激励同频率的周期运动,随着转速的提高,达到一定阈值时周期运动开始失稳。对迷宫密封的气动力采用Muszynska 非线性力学模型,支承采用短轴承,用打靶法求解转子运动周期解,并根据Floquet 理论分析了周期解的稳定性及失稳后的非线性动力学行为。     

Effect of dilution holes on the performance of a triple swirler combustor

A triple swirler combustor is considered to be a promising solution for future high temperature rise combustors. The present paper aims to study dilution holes including primary dilution holes and secondary dilution holes on the performance of a triple swirler combustor. Experimental investigations are conducted at different inlet airflow velocities(40–70 m/s) and combustor overall fuel–air ratio with fixed inlet airflow temperature(473 K) and atmospheric pressure. The experimental results show that the ignition is very difficult with specific performance of high ignition fuel–air ratio when the primary dilution holes are located 0.6H(where H is the liner dome height)downstream the dome, while the other four cases have almost the same ignition performance. The position of primary dilution holes has an effect on lean blowout stability and has a large influence on combustion efficiency. The combustion efficiency is the highest when the primary dilution holes are placed 0.9H downstream the dome among the five different locations.For the secondary dilution holes, the pattern factor of Design A is better than that of Design B.