一种针对结构损伤的非线性容错飞行控制方法

飞机结构损伤会引起气动参数变化,进而影响系统的静稳定性和控制精度。针对具有多输入的非线性飞机模型,利用带有二阶命令滤波器的自适应反步控制方法在线估计飞机气动参数,补偿结构损伤导致的气动参数变化对控制系统的影响,以实现容错飞行控制功能;引入的命令滤波器可以避免反步控制中复杂的求导运算。从理论上分析证明了带有二阶命令滤波器的自适应反步控制的闭环系统稳定性,并给出了控制跟踪误差的理论上界和二阶命令滤波器频率参数选取的下界。通过一个大型客机垂直尾翼脱落场景的仿真实验,验证了所提容错控制方法的有效性。     

基于自适应不对称高斯基函数网络的可靠飞行跟踪控制

针对歼击机操纵面结构故障,提出了一种基于自适应不对称高斯基函数网络（AGBFN）的可靠跟踪控制方案。该方案的特点是在传统的线性控制器的基础上,引入基于自适应AGBFN的自适应控制器,用于在线补偿由于建模误差、外扰、以及操纵面卡死或损伤所造成的影响,并且采用控制隔离技术来处理执行机构的饱和问题。完全自适应AGBFN采用不对称高斯基函数,并且可以在线更新网络所有参数,克服了传统RBF网络对称性约束,提高了网络的适应性和学习能力,从而保证歼击机的操纵品质,且输出较好地跟踪参考模型输出。飞行仿真结果表明,文中采用的控制方法使飞机在正常状态和故障状态下均可获得满意的控制效果。     

机械手的神经网络自适应滑动模控制器设计

 针对多关节机械手的鲁棒跟随控制器设计问题，提出了一种新的机械手神经网络自适应滑动模控制器设计方法，机械手的动力学非线性假设是完全未知的。在提出的控制结构中，高斯径向基函数神经网络用于在线补偿机械手的动力学非线性，参数学习律由稳定性理论得到。给出了系统稳定性和参数收敛性的证明。最后提出方法的可行性通过仿真得到验证。     

推力矢量飞机自适应控制系统仿真平台研究

研究了具有自修复功能的推力矢量飞机自适应控制系统的结构功能特点,研究了RHO优化控制算法实现在线控制器设计,利用MSLS辨识算法实现在线飞行参数辨识和等价空间算法、传感器信息融合技术和概率统计理论实现FDI算法。并且根据系统各个部分的算法,采用面向对象技术语言VC 6.0和三维图形语言OpenGL开发了仿真平台,利用仿真平台实时演示了飞机存在舵面故障情况下的飞行控制系统运行仿真,解决了飞机飞行过程中存在舵面损伤和气动参数变化的问题,该仿真平台可以根据需求进行飞机故障加载,具备完备的推力矢量飞机自适应控制系统仿真功能。     

质量矩固体推进微纳卫星自适应反演控制律设计

为解决微纳卫星利用固体火箭推进器进行快速轨道机动时的姿态翻滚问题,提出了利用质量矩技术对卫星的俯仰、偏航通道姿态进行稳定控制。首先考虑推进剂燃烧、质量块运动等因素引起的系统质量特性参数的变化,建立质量矩固体推进微纳卫星姿态动力学模型;然后分析了推进剂燃烧、质量矩控制引入的系统模型参数不确定性、连续有界未知干扰;随后基于反演控制方法,设计了卫星姿态角和姿态角速度双回路自适应滑模动态面控制器,利用自适应算法调节控制参数估计来补偿不确定因素的影响;基于Lyapunov函数证明了闭环系统的稳定性。最后,通过数值仿真验证了控制算法的有效性。     

飞行器动态稳定性参数计算方法研究进展

动态稳定性参数（简称动导数）是飞行器控制系统设计、飞行器动不稳定发生边界分析及相应动态稳定性判据研究的关键气动参数。在对飞行稳定性问题进行概述的基础上,介绍飞行器动态稳定性参数数值模拟的国内外研究进展。并按照理论方法、工程近似方法及计算流体力学（CFD）模拟方法的动导数发展方向对近年来主要的动导数计算方法进行了综述,评价了各种动导数预测方法的优缺点,指出了动导数数值模拟在理论基础、非定常气动力建模、预测方法精度和效率等方面存在的问题。最后对动导数数值模拟的发展趋势进行了展望。     

一种鲁棒的非线性飞行控制律设计

介绍了一种反馈线性化方法——逆系统方法，用以解决非线性飞行控制。针对逆系统方法存在的误差，介绍了一种鲁棒控制方法——基于RBF神经网络直接自适应控制方法，利用李亚普诺夫稳定性定理推导了神经网络权值的自适应规律，保证了闭环系统的稳定性。设计了针对滚转通道的神经网络，并应用某型号飞机进行了非故障和故障状态的仿真，结果证明，自适应神经网络控制方法补偿作用显著，相当于系统具有一定的重构功能。     

Adaptive Integral-type Sliding Mode Control for Spacecraft Attitude Maneuvering Under Actuator Stuck Failures

A fault tolerant control (FTC) design technique against actuator stuck faults is investigated using integral-type sliding mode control (ISMC) with application to spacecraft attitude maneuvering control system. The principle of the proposed FTC scheme is to design an integral-type sliding mode attitude controller using on-line parameter adaptive updating law to compensate for the effects of stuck actuators. This adaptive law also provides both the estimates of the system parameters and external disturbances such that a prior knowledge of the spacecraft inertia or boundedness of disturbances is not required. Moreover, by including the integral feedback term, the designed controller can not only tolerate actuator stuck faults, but also compensate the disturbances with constant components. For the synthesis of controller, the fault time, patterns and values are unknown in advance, as motivated from a practical spacecraft control application. Complete stability and performance analysis are presented and illustrative simulation results of application to a spacecraft show that high precise attitude control with zero steady-error is successfully achieved using various scenarios of stuck failures in actuators.     

MMAE-based control redistribution applied to the VISTA F-16

A novel control technique, termed control redistribution, is presented and applied in conjunction with multiple model adaptive estimation (MMAE) to the variable in-night stability test aircraft (VISTA) F-16, to detect and compensate for sensor and/or actuator failures. This ad hoc method redistributes control commands (that would normally be sent to failed actuators) to the nonfailed actuators, accomplishing the same control action on the aircraft. Dither is considered to help disambiguate failures in the longitudinal and lateral-directional channels. Detection of both single-actuator and single-sensor failures is considered. Failures are demonstrated detectable in less than 1 s, with an aircraft output nearly identical to that anticipated from a fully functional aircraft in the same environment     

Identification of Aircraft Stability and Control Parameters Using Hierarchical State Estimation

Previous attempts to identify aircraft stability and control derivatives from flight test data, using three-degrees-of-freedom (3-DOF) longitudinal or lateral-directional perturbation equation-of-motion models, suffer from the disadvantage that the coupling between the longitudinal and lateral-directional dynamics has been ignored. In this paper, the identification of aircraft stability parameters is accomplished using a more accurate 6-DOF model which includes this coupling. Hierarchical system identification theory is used to reduce the computational effort involved. The 6-DOF system of equations is first decomposed into two 3-DOF subsystems, one for the longitudinal dynamics and the other for the lateral-directional dynamics. The two subsystem parameter identification processes are then coordinated in such a way that the overall system parameter identification problem is solved. Next, a six-subsystem decomposition is considered. Computational considerations and comparison with the unhierarchically structured problem are presented.     

Application of neural networks for the design of flight control algorithms. II Adaptive tuning of neural network control law

In this paper, we consider different approaches for the neural network controller tuning in the flight control system. Two of the most common tuning approaches in the adaptive control theory are applied. The first one uses parameter identification technique and consists in solving a real-time regression problem for the control law. The second approach is based on the Lyapunov direct method, which utilizes a tracking error as an absolute measure of tuning performance. The neural network control law are designed for the three-axis flight control problem and tested on the full nonlinear model of a fighter aircraft. Closed loop simulation results are presented and two adaptation algorithms are compared in the case of abrupt change of aircraft dynamics.     

I-O map inversion, zero dynamics and flight control

The trajectory control of aircraft in rapid, nonlinear maneuvers is discussed. Based on nonlinear invertibility theory, a control law is derived to independently control roll, pitch, and sideslip angles using rudder, elevator, and aileron. Integral feedback is introduced in order to obtain robustness in the control system to parameter uncertainty. The stability of the zero dynamics is examined. Simulation results are presented to show that in a closed-loop system, precise simultaneous lateral and longitudinal maneuvers can be performed despite the presence of uncertainty in the stability derivatives     

空天飞行器直接力/气动力复合容错控制

考虑发生发动机推力损失故障的空天飞行器，针对直接力、气动力复合容错控制问题，设计一种基于自适应滑模的容错控制策略。首先，对于发生推力损失故障的摆动发动机，考虑X型安装的实际特点，对线性化后的俯仰通道控制模型进行故障等效，并采用自适应的方法对故障及干扰信息进行估计，综合利用舵面与发动机摆动角进行容错控制器设计。其次，考虑纵向容错控制对飞行器横侧向稳定性的影响，基于自适应反步的方法，利用方向舵与组合工作的左、右升降舵抵消干扰力矩的影响，保证横侧向的稳定。最后，基于李雅普诺夫稳定性理论，对所采用方法进行了分析，并通过仿真结果验证了所设计的复合容错控制方案的有效性。     

Active fault tolerant control for vertical tail damaged aircraft with dissimilar redundant actuation system

This paper proposes an active fault-tolerant control strategy for an aircraft with dissim-ilar redundant actuation system (DRAS) that has suffered from vertical tail damage. A damage degree coefficient based on the effective vertical tail area is introduced to parameterize the damaged flight dynamic model. The nonlinear relationship between the damage degree coefficient and the corresponding stability derivatives is considered. Furthermore, the performance degradation of new input channel with electro-hydrostatic actuator (EHA) is also taken into account in the dam-aged flight dynamic model. Based on the accurate damaged flight dynamic model, a composite method of linear quadratic regulator (LQR) integrating model reference adaptive control (MRAC) is proposed to reconfigure the fault-tolerant control law. The numerical simulation results validate the effectiveness of the proposed fault-tolerant control strategy with accurate flight dynamic model. The results also indicate that aircraft with DRAS has better fault-tolerant control ability than the traditional ones when the vertical tail suffers from serious damage.     

DO 28非线性多点模型的建立及其参数估计

 本文建立了DO 28试验机的非线性六自由度多点数学模型。该模型考虑了飞机运动的高度非线性,螺旋桨、机翼、尾翼空气动力特性,改进的推力计算,风场干扰以及飞行试验数据一致性检验和校正。与一点模型相比,该模型能更准确地描述飞机的运动,更适合飞机的参数估计。     

侧向稳定系统参数平面设计法

首先介绍了鲁棒系统设计的参数平面法，然后采用该方法对某支线客机的侧向稳定系统进行了鲁棒设计，最生以几种不同的飞行状态为例，通过计算机仿真，对所设计的控制律参数进行了验证，结果表明：飞机侧向稳定系统的参数平面法设计是可行的。     

航天器有限时间自适应姿态跟踪容错控制

非刚体航天器存在时变的惯量、执行器完全失效或衰退故障以及外界干扰的情况,提出一种有限时间自适应姿态跟踪容错控制方法。首先,基于有限时间理论和自适应方法,设计惯量不确定性自适应估计项和外界干扰参数自适应估计项进行系统补偿,克服惯量不确定性和抑制外界干扰;然后,基于容错控制和双幂次方法,设计一种自适应有限时间姿态跟踪容错控制算法,并且利用Lyapunov稳定性理论证明所提算法能够保证航天器姿态跟踪系统实际有限时间稳定;最后,对仿真结果进行验证。结果表明:所提有限时间姿态跟踪容错控制方法是有效的。     

基于无味卡尔曼滤波的飞机防滑刹车模糊神经网络控制

根据对飞机刹车过程动力学分析与建模,本文提出了一种基于无味卡尔曼滤波(UKF)的模糊神经网络控制律。本控制律结合了无味卡尔曼滤波对机体速度的良好估计效果和模糊神经网络控制器对不同系统参数的适应能力,能够很好完成对最佳滑移率的追踪任务。Matlab仿真试验结果显示,基于无味卡尔曼滤波的模糊神经网络控制器可以准确的估计飞机滑跑时的速度,改善飞机防滑刹车系统性能,提高刹车效率。     

Nonlinear adaptive and sliding mode flight path control of F/A-18 model

The question of inertial trajectory control of aircraft in the three-dimensional space is discussed. It is assumed that the nonlinear aircraft model has uncertain aerodynamic derivatives. The control system is decomposed into a variable structure outer loop and an adaptive inner loop. The outer-loop feedback control system accomplishes (x,y,z) position trajectory and sideslip angle control using the derivative of thrust and three angular velocity components (p,q,r) as virtual control inputs. Then an adaptive inner feedback loop is designed, which produces the desired angular rotations of aircraft using aileron, elevator, and rudder control surfaces to complete the maneuver. Simplification in the inner-loop design is obtained based on a two-time scale (singular perturbation) design approach by ignoring the derivative of the virtual angular velocity vector, which is a function of slow variables. These results are applied to a simplified F/A-18 model. Simulation results are presented which show that in the closed-loop system asymptotic trajectory control is accomplished in spite of uncertainties in the model at different flight conditions.     

Stability,flying qualities and longitudinal parameter estimation of a twin-engine CS-23 certified light aircraft

This paper presents some results of the flight test campaign conducted on the Tecnam P2006T aircraft, on the occasion of its certification process. This twin-engine propeller airplane is certified under the normal category CS-23 and FAR 23. A prototype of this light aircraft has been tested in flight for a post-design performance optimization and for the assessment of flight qualities. These experiences have led to the application of two winglets to the original wing. The final configuration has been extensively tested for the achievement of CS-23 certification. The longitudinal and lateral-directional response modes have been assessed and quantified. At the same time the longitudinal airplane model, through a dedicated set of flight maneuvers, has been characterized by means of parameter estimation studies. The aircraft stability derivatives have been estimated from the acquired flight data using the identification technique known as Output Error Method (OEM). Some estimated stability derivatives have been also compared with the corresponding values extracted from leveled flight tests and from wind tunnel tests performed on a scaled model of the aircraft.