共查询到16条相似文献,搜索用时 156 毫秒
1.
莫宗云 《华北航天工业学院学报》2011,(2):4-5,12
根据张弦梁结构的思想提出由组合网架和索通过支杆相连而形成的预应力结构即弦支组合网架结构。建立一弦支组合网架结构的计算模型,利用ANSYS有限元软件分析结构在不同预应力作用下的静力和自振特性。得知预应力能够较为明显的改善结构位移和杆件内力,即索内初始预应力越大,结构位移和杆件内力越小;改变预应力对结构的自振特性几乎没有影响。 相似文献
2.
根据张弦梁结构的思想提出由组合网架和索通过支杆相连而形成的预应力结构即弦支组合网架结构。建立一弦支组合网架结构的计算模型,利用ANSYS有限元软件分析结构基于位移性能下的正常使用极限可靠度。经软件分析得出在所给几何尺寸、材料特性、预应力、恒荷载以及活荷载等随机变量作用下,结构基于位移正常使用极限状态下的可靠度是良好的;对结构位移影响最大的变量是预应力,影响最小的变量是混凝土板肋的截面尺寸;可靠度为95%的结构最大位移值是60mm。 相似文献
3.
根据张弦梁结构的思想提出由组合网架和索通过支杆相连而形成的预应力结构即弦支组合网架结构。建立一弦支组合网架结构的计算模型,利用ANSYS有限元软件分析结构基于位移性能下的正常使用极限可靠度。经软件分析得出在所给几何尺寸、材料特性、预应力、恒荷载以及活荷载等随机变量作用下,结构基于位移正常使用极限状态下的可靠度是良好的;对结构位移影响最大的变量是预应力,影响最小的变量是混凝土板肋的截面尺寸;可靠度为95%的结构最大位移值是60mm。 相似文献
4.
5.
空间站柔性太阳翼上有以下预应力:1)在轨工作时,会周期性进出地球阴影区,结构温度会发生周期性的变化,温差在结构上产生了热应力;2)中央桁架斜拉杆上作用有展开预应力;3)柔性阵面上施加有张紧力。这些预应力都会引起几何刚度,从而改变太阳翼结构的动力学特性。文章使用Abaqus非线性动力学求解功能,首先对中央桁架部分和柔性阵面部分分别建立有限元模型,研究预应力对太阳翼动力学特性的影响,发现只有柔性阵面上的张紧力影响最为显著;然后针对完整的太阳翼结构,考虑阵面张紧力作用下,研究其动力学特性,并与未考虑预应力引起的刚度变化时的结构动力学特性进行对比分析。 相似文献
6.
7.
本文运用梁单元和索单元组成的混合有限元法对预应力索-拱结构平面内弹塑性极限承载力进行研究.利用牛顿-拉弗森法和弧长法对荷载-位移平衡路径进行跟踪研究,研究了索的预应力对结构极限承载力的影响,通过对这种新型结构的分析和研究,从中获得了对预应力索-拱结构设计有益的结论. 相似文献
8.
9.
WANG Jiang ZHOU Hui 《华北航天工业学院学报》2007,(5)
本文运用梁单元和索单元组成的混合有限元法对预应力索—拱结构平面内弹塑性极限承载力进行研究。利用牛顿—拉弗森法和弧长法对荷载—位移平衡路径进行跟踪研究,研究了索的预应力对结构极限承载力的影响,通过对这种新型结构的分析和研究,从中获得了对预应力索—拱结构设计有益的结论。 相似文献
10.
11.
12.
13.
采用AMESim软件对氮气贮存压力为1.5×10 7 Pa、推力范围为mN级的压电驱动的氮气微推进系统进行建模。研究了氮气填充过程中氮气瓶、减压阀的压力和质量流量瞬态特性。分析了整合喷管的压电比例阀在开机过程中的瞬态工作特性。最后,研究了驱动电压对压电比例阀在开机过程中的阀芯位移和喷管推力瞬态值、阀芯运动和推力响应时间的影响规律。结果显示,当驱动电压为80 V时,阀芯的响应时间和稳定位移分别为 0.64 ms 和3.67 μm。开机后8 ms,喷管推力达到稳定值(0.588 mN)。压电比例阀阀芯的开启响应快速,且驱动电压与喷管推力之间存在良好的线性关系,说明推力可通过改变驱动电压进行mN级的线性调节。 相似文献
14.
The inter-satellite electromagnetic forces generated by the magnetic dipoles on neighboring satellites provide an attractive control actuation alternative for satellite formation flight due to the prominent advantages of no propellant consumption or plume contamination. However, the internal force nature as well as the inherent high nonlinearity and coupling of electromagnetic forces bring unique dynamic characteristics and challenges. This paper investigates the nonlinear translational dynamics, trajectory planning and control of formation reconfiguration actuated by inter-satellite electromagnetic forces. The nonlinear translational dynamic model is derived by utilizing analytical mechanics theory; and analysis on the dynamic characteristics is put forward. Optimal reconfiguration trajectories of electromagnetic force actuated formation are studied by applying optimal control theory and the Gauss pseudospectral method. Considering the high nonlinearity and uncertainty in the dynamic model, an inner-and-outer loop combined control strategy based on feedback linearization theory and adaptive terminal sliding mode control is proposed with finite-time convergence capability and good robust performance. Theoretical analysis and numerical simulation results are presented to validate the feasibility of the proposed translational model, reconfiguration trajectory optimization approach and control strategy. 相似文献
15.
流体计算采用基于非结构动网格的有限体积方法,结构计算采用分段精细时程积分方法,求解结构动力学有限元方程,流体计算和固体计算之间采用松耦合在不断运动的交界面上进行作用力和运动特性的传递,对固体火箭发动机点火形成的冲击波与药柱缺陷形成的弹性裂纹之间相互耦合作用过程进行了模拟。研究表明,作用在弹性裂纹上的冲击波载荷引起的壁面变形随时间变化明显,开始表现为撑开裂纹出口,随后出现了收缩出口撑开底部的瓶状;固体变形对冲击波在弹性狭缝内的压力波振荡影响较小,以前采用刚体模型得到的研究结论仍有指导意义。 相似文献
16.
In this paper, we study the nonlinear deformation of a longitudinally corrugated shell (a type of morphing structure) with a uniform load. We derived the governing equations of the deformations of that corrugated shell with Nayfeh and Pai's [1] initial curvature of shell geometries and developed numerical solutions for that nonlinear mechanics problem. This numerical method is extremely efficient since no element discretization is implemented. The obtained solutions can be verified by comparing with the analytical solution for the same structure with infinitesimal strains. Furthermore, we apply the present method to study a cylindrical shell under the uniform internal pressure, and find that the displacements and internal forces of the cylindrical shell agree well with results obtained from von Kármán nonlinear shell theory. Finally, from parametric studies, we can figure out that the increment of the percentage of the arc part and the total length of the corrugated ring can increase the expansion and internal forces of the corrugated ring. And the configuration of the corrugated ring are more sensitive to the change of geometry and material parameters than internal forces, which indicate that the morphing function can be realized through the change of geometry and material parameters of the structure without great change in the maximum internal forces of the ring. By comparing the results from present nonlinear theory with those from linear theory, we can also find that the displacements and internal forces obtained from linear shell theory can either be exaggerated or disguised for the different configurations of the ring. 相似文献