Analysis and design of (LC)(LC)-type series-parallel resonantconverter

A series-parallel resonant converter employing (LC)(LC)-type tank circuit operating in lagging power factor (PF) mode is presented and analyzed using complex ac circuit analysis. Design curves are obtained and the converter is optimized under certain constraints. Detailed Space Integrated Control Experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load conditions. Results obtained from an experimental converter are also presented. The results obtained from the theory, SPICE simulation, and the experimental converter are compared. The proposed converter has high efficiency from full load to very light load (<10%). Switching frequency variation required for a wide change in the load (near load open circuit to full load) is narrow compared with the series resonant converter (SRC)     

Analysis and design of a three-phase LCC-type resonant converter

A three-phase dc-to-dc LCC-type resonant converter with high-frequency transformer isolation is proposed. The operation and a simple analysis of the converter are presented. Design curves are obtained and a design example is given. SPICE simulation and experimental results are presented to verify the performance of the proposed converter for varying load conditions. The converter proposed has several advantages, e.g., operation in lagging PF mode for the entire load range, requires a narrow variation required in switching frequency, reduced component size and stresses, etc     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

Single-phase power-factor-correction AC/DC converters with threePWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements     

High power factor operation of DCM series-parallel resonantconverter

This work presents the operating principle, analysis, design, simulation, and experimental results for a high frequency (HF) transformer isolated single stage ac-to-dc series-parallel resonant converter (SPRC) operating on the utility line, in discontinuous current mode (DCM). The equivalent circuit models and the state space analysis of the SPRC in DCM are presented. PROMATLAB software is used to solve the equations and to obtain important design parameters. SPICE3 simulation and experimental results obtained from a 150 W prototype are presented to verify the analysis. High power factor operation (>0.99) with low harmonic distortion (<18%) have been achieved for the entire load range even without active control, in addition to eliminating switching losses     

Analysis and design of series-parallel resonant power supply

A modified series-parallel high-frequency resonant DC/DC converter configuration is proposed. A simplified steady-state analysis of the converter, including the effect of a high-frequency transformer using complex circuit analysis, is presented. Based on the analysis, a simple design procedure is given. The effect of magnetizing inductances of the high-frequency transformer on the performance of the converter is discussed. Detailed experimental results obtained from a MOSFET (metal-oxide-semiconductor field-effect-transistor)-based 1-kW converter are presented to verify the analysis. The converter presented has almost constant efficiency from full load to quarter load, and the converter has load short circuit capability     

Flyback Converter Output Voltage Stabilization

The expression of the flyback converter output voltage (output power) is derived as a function of the supply voltage, load resistance, transformer ratios, transistor current gain, and base-circuit resistor value. Switching period and duty cycle are also calculated. A converter circuit is designed having stabilized output voltage, with respect to supply voltage, at constant load. The transistor base current is controlled by the supply voltage, via a nonlinear circuit. This feedforward circuit approximates with logarithmic characteristics the ideal hyperbolic dependence of the transistor base current as a function of the supply voltage. The converter has high performance and low cost. A cheaper circuit variant is presented, in which the high-voltage control transistor was eliminated.     

Single-Stage Single-Switch Switched-Capacitor Buck/Buck-Boost-Type Converter

A new dc-dc converter featuring a steep step-down of the input voltage is presented. It answers a typical need for on-board aeronautics modern power architectures: power supplies with a large conversion ratio able to deliver an output voltage of 1–1.2 V. The proposed structure is derived from a switched-capacitor circuit integrated with a buck converter; they share the same active switch. The proposed solution removes the electromagnetic interference (EMI) emission due to the large di/dt in the input current of the switched-capacitor power supplies. Compared with a quadratic buck converter, it presents a similar complexity, a smaller reduction in the line voltage at full load (but less conduction losses due to smaller input inductor current and capacitor voltage), lower voltage stresses on the transistor and diodes, lower current stresses in the diodes, and smaller size inductors. A similar structure using a buck-boost converter as the second stage is also presented. The experimental results confirm the theoretical developments.     

Single-phase grid-connected PV system using three-arm rectifier-inverter

A grid-connected photovoltaic (PV) power supply system with on-line voltage regulation capability is presented. It employs the three-arm rectifier-inverter topology with PV modules connected directly on the dc-link. The common-arm is with line-frequency switching and synchronous to the input voltage, aiming for a lower switching loss and decoupling the control of rectifier and inverter portions. As a result, the rectifier and inverter portions can be controlled independently with the rectifier-arm and inverter-arm, respectively. For maximum power point tracking (MPFF) of the PV modules and balancing the power among utility, PV, and the load, a variable dc-link voltage is adopted and controlled by the rectifier-arm based on the MPPT control algorithm. The inverter-arm then regulates the load voltage with good regulation and low distortion. Due to large variation of the dc-link voltage, a feedforward plus feedback control technique with variable gain is developed to keep constant bandwidth of the current loop at any operation condition. Therefore, the performance of the rectifier and inverter portions can be ensured. A system containing a 2 kVA converter and a 1.2 kW PV module is set up, and some experimental results are provided for demonstrating the effectiveness of the proposed method.     

A new zero-voltage switching DC/DC boost converter

A pulsewidth-modulated (PWM) zero-voltage-switching quasi-resonant boost converter operating at constant switching frequency is presented. In contrast to the frequency-modulated (FM) zero-voltage-switching quasi-resonant boost converter, this converter possesses better controllability and higher operating performance, and overcomes the instability caused by the parasitic oscillation. The principle of operation and performance of the converter are presented. Its two-dimensional state trajectories and steady-state characteristic curves are derived which are useful for the converter design. Both the SPICE simulation and experimental result agree with the theoretical prediction     

Frequency-controlled series-resonant converter with synchronous rectifier

This paper presents an analysis and experimental results for a frequency-controlled series-resonant dc-dc converter that consists of a Class-D zero-voltage-switching (ZVS) series-resonant inverter and a center-tapped synchronous rectifier. If the dc output voltage is low, the efficiency of the converter is dominated by the efficiency of the rectifier. Low on-resistance metal-oxide-semiconductor field-effect transistors (MOSFETs) are used in the rectifier instead of diodes because the forward voltage drop across the rectifying device is low, resulting in a high efficiency. The dc output voltage is regulated against variations in the load resistance and the dc input voltage by varying the operating frequency. Experimental results are presented for a converter with a dc input voltage of 150 V, an output voltage of 5 V, and a dc load resistance ranging from 0.5 to 5.5 R. The measured efficiency was 86% for a 50 W output and 89% for a 25 W output. The theoretical results were in good agreement with the measured results.     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Space vector modulation strategy for an eight-switch three-phase NPC converter

A three-phase neutral point clamped (NPC) converter is presented for power factor correction and dc-link voltage regulation. A simplified space vector pulsewidth modulation scheme (SVPWM) is adopted to track line current commands. Using a simplified SVPWM algorithm, the calculated time for the time duration of voltage vector is reduced. The adopted NPC converter has less power switches compared with the conventional three-level NPC converter. Only eight power switches and four clamping diodes with voltage stress of half the dc bus voltage are used in the circuit configuration. Based on the proposed control algorithm, a reference voltage vector is generated on the ac terminal for drawing the sinusoidal line currents with unity power factor. Computer simulation and experimental results based on a laboratory prototype are presented to verify the validity and effectiveness of the proposed control strategy.     

Novel AC-DC and DC-DC converters with a diode-capacitor multiplier

This paper presents a transformerless ac-dc and or dc-dc converter with a high output voltage multiplicity, which contains only one switch. The converter consists of an inverter and a diode-capacitor multiplier (DCM) and provides a voltage gain equal to double the number of multiplier steps. In the case of ac-dc conversion the proposed converter offers a practically unit power factor and provides a sine wave input current. The analysis of the steady state as well as the transient behavior of the DCM is given and simplified equivalent circuits are proposed. The prototype of the DCM has been built and tested to show the validity of the proposed converter. The theoretical analysis, the computer simulation results, and the experimental testing results are in good agreement.     

Z-源稀疏矩阵变换器励磁的双馈风力发电系统

针对矩阵变换器电压传输比低和其励磁的双馈风力发电系统(DFIG)易受非正常输入波动影响的不足,提出了一种适用于DFIG励磁的Z-源稀疏矩阵变换器系统。利用Z-源的升压特性来提高电压传输比,检测电容电压实现对直通因子的自动调节,从而实现对网侧波动的自动抑制。建立了系统数学模型,推导了DFIG系统定子磁场定向矢量控制策略表达式,搭建试验样机对所提方案进行试验验证,在亚同步、同步、超同步三种发电状态下的波形和并网试验结果验证了方案的可行和有效性。     

A novel resonant converter topology for DC-to-DC power supply

A class-E DC-to-DC converter with half-wave controlled current rectifier is proposed. Its output voltage is controlled by the conduction angle of the rectifier switch at constant switching frequency. Zero voltage switching for all the switches can be maintained from full load to no load. Its steady state characteristics are analyzed and the effects of the circuit parameters are studied. Some extensions of the proposed converter are also discussed. The analysis is verified by PSPICE simulation and an experimental prototype     

Capacitive-loaded push-pull parallel-resonant converter

Results of a theoretical and experimental investigation of a capacitive-loaded push-pull parallel-resonant DC-DC converter (CL-PPRC) are presented and discussed. The push-pull parallel-resonant converter (PPRC) is driven by a lower-than-resonance frequency and the secondary voltage is rectified and smoothed by a capacitive filter. The CL-PPRC is shown to operate in the zero voltage switching (ZVS) mode with a boost-like DC transfer ratio that is approximately linear with the period of the switching frequency. Experimental results of a 180 W, high output voltage (1.8 KV) prototype are found to be in good agreement with the analysis, models, and simulation results presented. The basic characteristic of ZVS, the fact that the resonant current is passing through the switches only during a fraction of the period, the high-voltage transfer ratio, and the inherent input/output (I/O) isolation, make the proposed topology a viable design alternative in avionic and aerospace applications     

Power factor correction circuits with robust current control technique

A dynamically robust current control method to synthesize a sinusoidal input current for AC-to-DC converters with boost type topology is presented. Under this control strategy, the inductor current and the diode current of the boost converter are fed back and combined in a special way which makes the input current of the AC-to-DC converter stable and robust. The input current is solely determined by the reference current. When the reference current signal is derived from the sinusoidal input voltage, the input current is sinusoidal and in phase with the input voltage. Theoretical analysis is first provided. Small signal analysis shows that the current loop is inherently stable and has a fast dynamic response. Large signal analysis reveals that the control system is not affected by large disturbances in supply voltage or output load. Computer simulations have been carried out and experimental prototype models have been built to verify the analysis and demonstrate the feasibility of the control strategy. A power factor of 0.998 and a total harmonic distortion (THD) of 3.18% are measured.     

ZVT boost converter using a ZCS auxiliary circuit

A soft switching boost converter with zero-voltage transition (ZVT) main switch using zero-current switching (ZCS) auxiliary switch is proposed. Operating intervals of the converter are presented and analyzed. Design considerations are discussed. A design example with experimental results obtained from a 600 W, 100 kHz, 380 V output, power factor corrected, ac-to-dc, boost converter using insulated gate bipolar transistors (IGBTs) is presented, Results show that the main switch maintains ZVT while the auxiliary switch retains ZCS for the complete specified line and load conditions