基于序列图像的航天器自主导航降维滤波方法

非合作目标的运动感知与状态估计,是太空领域技术发展的重要组成部分。非合作目标相对状态的精确估计是相对导航的难点问题。传统的非合作目标扩展卡尔曼滤波算法需要结合非合作目标的质心位置,增加了状态变量的维数,提高了系统不确定性,从而会影响状态扩展卡尔曼滤波的收敛速度。提出了一种基于序列图像的非合作目标相对导航方法,该方法在不对质心进行估计的情况下首先对非合作目标姿态进行估计,在完成非合作目标姿态估计后再对其质心进行估计。本文推导了光学相机测量值与目标真实姿态的关系,构建了基于序列图像的测量模型,分别建立了不含有非合作目标质心位置的状态方程和基于非合作目标位置、速度矢量的状态方程,设计了适用于非合作目标状态估计的扩展卡尔曼滤波算法。仿真实验表明该方法可在10 Hz采样频率下经过50次采样（即5 s）内快速收敛,从而有利于空间飞行器的在轨服务与维护。     

ANALYSIS OF LOCATION ACCURACY FOR AN EMITTER USING SATELLITE- MOUNTED INTERFEROMETER

ＡＮＡＬＹＳＩＳＯＦＬＯＣＡＴＩＯＮＡＣＣＵＲＡＣＹＦＯＲＡＮＥＭＩＴＴＥＲＵＳＩＮＧＳＡＴＥＬＬＩＴＥ┐ＭＯＵＮＴＥＤＩＮＴＥＲＦＥＲＯＭＥＴＥＲＺｈｏｕＹｉｙｕ（周一宇）,ＧｕｏＺｈｉｇａｎｇ（郭志刚）（ＮａｔｉｏｎａｌＵｎｉｖｅｒｓｉｔｙｏｆＤ...     

频率源振动对测速精度的影响

针对频率源振动会影响测速精度的问题,按照国军标车载设备的振动要求,对频率源振动带来的相位噪声进行仿真分析和实际测试。并以振动频率为5Hz为例,对10 MHz频率源进行测试计算得到相应短稳;然后计算频率源在静止和振动环境下的测速随机误差;最后通过比较得到频率源在振动时测速精度会恶化几个数量级的结果。建议在动中测速时,通过使用加速度灵敏度低的晶振,安装减震器,优化环路设计,采用数字补偿技术等措施以减少振动对测速精度的影响。     

机载单站无源定位系统中相位差变化率提取方法(英文)

相位差变化率含有目标辐射源的距离信息,是机载单站无源定位系统中的重要参数。本文以正弦单载波脉冲信号为例,分析了基于相位差变化率的单站无源定位原理,以及测量误差的组成。基于对Cramer-Rao下限的分析,提出了一种基于多次观测的相位差变化率的高精度测量方法——时间片处理法。在相位差变化率的测量中,当信噪比较低时,频域鉴相方法优于时域鉴相方法,多时间片处理能够显著地降低测量方差,仿真验证了此算法的正确性和有效性。典型的无源定位场景的仿真验证了算法对动态测量的适应性。此测量算法简单、计算量小,易于实现。     

一种基于概率的双星无源定位算法

针对双星无源定位系统采用时差、频差对地面固定辐射源进行无源定位的问题,提出了一种基于概率的双星无源定位算法。通过公式推导,将复杂的定位方程组化简为简单的二元一次方程组。在介绍定位原理的基础上对该算法进行仿真,通过仿真,分析了定位误差与时差测量精度、频差测量精度的关系。     

Determination of ground emitter location

Passive techniques to locate ground emitters from an airborne platform provide threat warning to aircraft in hostile airspace while maintaining the electronic silence of the vehicle. These techniques are based on triangulation methods and extended Kalman filters, using only hearing measurements. An approach that takes into consideration the maximum measurement error of the sensor and approximates an area of uncertainty of the emitter location by polygons is proposed. The performance of this algorithm is demonstrated by simulation results, and an example is shown for the comparison of this algorithm and the extended Kalman filter approach     

Emitter localization using clustering-based bearing association

A closed-form emitter location estimator using time difference of arrival (TDOA) measurements is developed based on triangulation of hyperbolic asymptotes. The problem of associating the asymptotes with the emitter is solved by clustering the bearing angles of the linear asymptotes using a kernel density estimate. A closed-form estimate of the emitter location is obtained from triangulation of the clustered bearings using a weighted version of the pseudolinear estimator. By way of simulation examples, the proposed closed-form estimator is shown to outperform the computationally demanding and divergence-prone maximum likelihood (ML) estimator at moderate TDOA noise levels.     

基于最大似然估计的TDOA/FDOA无源定位偏差补偿算法

在到达时差/到达频差(TDOA/FDOA)无源定位系统中,定位问题的非线性使得定位的结果存在偏差,特别是在噪声较大或者接收站布站不合理的情况下,定位的偏差尤其显著。针对这一问题,提出了一种基于最大似然估计的偏差补偿算法。该方法分为3步:首先,利用最大似然估计器对目标的位置和速度进行求解;其次,通过利用目标定位的估计值和含噪的测量值,对目标的位置和速度偏差值进行理论分析和推导;最后,将最大似然估计解减去理论偏差值,得到经过偏差补偿的新的目标定位解。理论分析和实验仿真证明,在一定噪声的情况下,所推导的目标位置和速度的理论偏差值与实际偏差值相符,并且经过偏差补偿后的定位算法,在保持目标定位的均方根误差(RMSE)与原最大似然算法一致的情况下,目标的位置和速度偏差值远远小于原最大似然算法的偏差值,目标定位精度得到了有效的提高。     

用双色激光多卜勒风速仪研究燃烧室的复杂流场

 本文总结了双色激光多卜勒风速仪系统在航空发动机蒸发管式模型燃烧室流场测量中取得的一些结果及应用经验。并与用常规方法测得的结果作了比较。     

Passive localization of frequency-agile radars from angle andfrequency measurements

It is well known that the position of a stationary radar can be estimated by a single moving observer from angle and/or frequency measurements taken passively at different points in its trajectory. Depending on the measurement set different localization methods result: the bearing method (BM), the frequency method (FM), and the combined method (CM). Previous studies analyze the three methods on the basis of constant emitter frequencies. However, radars with constant emitter frequencies are not realistic. Frequency drift and frequency hopping have to be taken into account. Therefore, to include radars the emitter model has been extended by drift and frequency hopping in this study, and the estimation methods have been reanalyzed. The effects of the model extensions become transparent in a parametric Cramer-Rao (CR) analysis. The results obtained in this way are confirmed by Monte Carlo simulations taking maximum likelihood (ML) as estimation procedure     

单载机相位差无源定位系统可观测性分析(英文)

With a pair of antennas spaced apart, an airborne passive location system measures phase differences of emitting signals. Regarded as cyclic ambiguities, the moduli of the measurements traditionally are resolved by adding more antenna elements. This paper models the cyclic ambiguity as a component of the system state, of which the observability is analyzed and compared to that of the bear- ings-only passive location system. It is shown that the necessary and sufficient observability condition for the bearings-only passive location system is only the necessary observability condition for the passive location system with phase difference measurements, and that when the system state is observable, the cyclic ambiguities can be estimated by accumulating the phase difference measurements, thereby making the observer able to locate the emitter with high-precision.     

Passive localization of moving emitters using out-of-planemultipath

The purpose of this work is to establish how a moving emitter, such as a jammer, can be localized by a passive receiver through the use of out-of-plane multipath signals reflected by the terrain. This is a novel localization technique that assumes no a priori knowledge of the localization of the multipath sources. The emitter parameters of range, heading, velocity, and altitude are estimated by exploiting the correlation between the direct-path signal and the delayed and Doppler modulated signals. Two basis assumptions about the scattering properties of the terrain lead to different maximum likelihood estimators (MLEs). The Cramer-Rao lower bounds (CRLB) are used to study estimator performance versus emitter velocity for each case. The proposed estimators are successfully demonstrated using field data collected at White Sands Missile Range (WSMR) during the DARPA/Navy Mountaintop program     

一种FMCW SAR地面运动目标谱图域参数估计方法

对调频连续波(FMCW)合成孔径雷达(SAR)地面运动目标的参数估计方法进行了研究,采用相位中心偏置天线(DPCA)技术对地杂波进行抑制,分析了载机及地面运动目标连续运动对回波信号的影响,推导了采用DPCA技术引入的回波慢时间包络(STE)项与地面运动目标参数之间的关系。在此基础上,提出了一种地面运动目标谱图域参数估计方法,该方法首先利用Radon变换在谱图域估计导致回波信号距离走动的目标等效径向速度,并对距离走动进行校正;其次,在谱图域中提取运动目标回波幅度,根据STE项引起的回波幅度变化与目标方位向速度之间的关系,估计目标的方位向速度,并进一步求解相应的目标径向速度。所提方法能够在谱图域完成地面运动目标二维速度估计,最后的仿真实验验证了所提方法的有效性和可行性。     

Parametric Methods for Strip-Map SAR Doppler Ambiguity Resolution

Physical modeling of the Doppler centroid (DC) can be used to predict synthetic aperture radar (SAR) Doppler ambiguity when antenna attitude is controlled or measured precisely enough. It is shown that the same model proves useful even in the cases of higher attitude uncertainty, if it is combined with suitable adaptive techniques. In this paper, Doppler ambiguity resolution is formulated as a hypothesis testing problem over a domain of integer values that are directly related to the attitude uncertainty. A test statistic is derived from the entire SAR scene using data adaptive processing. A broad class of such adaptive algorithms is analyzed in a unified way, starting from the range-azimuth coupling in the frequency domain and multilook techniques. The analysis includes two well-known and two new multilook methods for Doppler ambiguity resolution. A suitable test statistic is proposed for each of these methods and its dependency on the scene spatial correlation is discussed. Experimental results confirm the robustness of the combined scheme.     

低频标准角振动台

低频标准角振动台产生标准角位移、角速度和角加速度,用正弦信号对角位移传感器、角速度传感器(陀螺、转速表等)和角加速度计进行幅频和相频特性校准。简要介绍了低频标准角振动台的工作原理,并应用其对角运动传感器进行校准。校准范围为0.1~100H z;幅值灵敏度不确定度优于1%;相移不确定度小于1°。     

存在观测站位置误差的转发式时差无源定位

无源定位中,由于观测站安放在运动平台等原因造成的观测站位置误差会影响无源定位精度性能。另外到达时间差(简称时差)(TDOA)的转发式测量需要将不同观测站截获到的辐射源信号都转发到同一位置,如主观测站。针对这两个问题,提出了基于约束总体最小二乘(CTLS)的无源定位算法。首先将转发式时差的非线性定位方程转化为不需要中间变量的直接线性方程,再基于CTLS算法依次转化为约束优化问题和无约束优化问题,最后推导给出定位近似闭式解。仿真实验表明在观测站误差较大时,该算法与其他算法相比定位精度性能较好。     

利用不机动单站DOA、TOA的测量实现被动定位与跟踪

 可以利用多个被动探测器或单个机动的探测器实现对运动辐射源的被动定位与跟踪。本文介绍的是一种利用非机动的单个探测器所获得的DOATOA测量值,对运动辐射源实现被动定位与跟踪的新方法。在二维平面内对运动辐射源使用这种方法,通过计算机仿真显示可以获得收敛而精确的跟踪数据。     

动态纹影-光子相关测量技术在超音速剪切流中的应用

 对一个分离后的二维超音速剪切流进行动态纹影——光子相关测量,得到了剪切层中大尺度涡的迁移速度以及由大尺度涡流诱导的剪切层自维持振荡频率。同时由光子相关测量可以估算剪切层中紊流动能的分布。发现了高速剪切层中大涡结构的某些特殊性质。结果表明这一测量方法在复杂高速流动的测量中具有潜在的优势。     

高精度接触式扫描测头动态特性分析

本文在对高精度光学非球面摆臂式扫描测量方法简要介绍的基础上,建立了高精度接触式扫描测头的结构模型,详细分析了扫描速度对测量精度的影响规律.在此基础上.利用建立的摆臂式扫描测量系统对500mm口径,相对口径1:1的深型球面镜进行了相关测量实验并与干涉测量结果进行了比对.实验验证了上述分析的正确性.     

Particle Velocity Estimation Using Kalman Filtering

The velocity of a moving particle can be estimated by using the least squares method (LSM), but the estimation accuracy is not high. Here, a Kalman filtering method (KFM) is applied to estimate this velocity. A Kalman filtering formulation of the moving particle velocity is described and has been realized on a digital computer. According to a vast number of printouts, the advantages of KFM over LSM are a short filtering stability time and a high filtering accuracy.