电力作动器中永磁容错电机的电感和谐波分析

 针对永磁容错电机大漏感的特点,利用磁矢量有限元法对六相十极永磁容错电机进行分析,得出其绕组自感的组成成分,尤其是电机内漏感分布;同时建立六相十极永磁容错电机的磁路模型,利用磁路法推导出较高精度的绕组自感及其组成部分的解析式,通过有限元验证,该解析式的计算精度在5.6%以内。此解析式可推广到一般的永磁容错电机中去,进而为永磁容错电机的初始设计和性能分析提供了理论依据。最后,对永磁容错电机内谐波漏感进行了量化分析,为后续的电机控制及其热分析打下基础。     

具有高精度的永磁容错电机非线性电感分析及其解析式求取

 以六相十极永磁容错电机（FTPMM）为例,通过对电机中磁力线分布的分析,得出FTPMM绕组自感的各个主要组成部分,即激磁感、谐波漏感、槽口漏感和槽内漏感,并分析出FTPMM的大电感是通过增加槽口漏感和谐波漏感来实现的。为提高电机优化设计的正确性,提出了新的磁路模型,并引入槽口磁压降参数和槽口计算厚度参数,得出了具有高精度的非线性绕组自感及其组成部分的解析式。最后通过有限元法(FEM)及实验验证,该解析式的精度在13%以内,并且电机具有很强的容错能力,对永磁容错电机的优化设计和性能分析有理论指导意义。     

一种电感式位移传感器的电路系统设计

介绍了一种电感式位移传感器的电路系统.该系统以一片AD698芯片为信号调整电路的核心,将位移量输出信号转换为相应的直流电压值,并结合其它一系列电路模块实现了测头位移量测量.通过对测头的标定试验证明该系统精度高、线性测量范围大.     

Thermal Evolution and Magnetic Field Generation in Terrestrial Planets and Satellites

Of the terrestrial planets, Earth and Mercury have self-sustained fields while Mars and Venus do not. Magnetic field data recorded at Ganymede have been interpreted as evidence of a self-generated magnetic field. The other icy Galilean satellites have magnetic fields induced in their subsurface oceans while Io and the Saturnian satellite Titan apparently are lacking magnetic fields of internal origin altogether. Parts of the lunar crust are remanently magnetized as are parts of the crust of Mars. While it is widely accepted that the magnetization of the Martian crust has been caused by an early magnetic field, for the Moon alternative explanations link the magnetization to plasma generated by large impacts. The necessary conditions for a dynamo in the terrestrial planets and satellites are the existence of an iron-rich core that is undergoing intense fluid motion. It is widely accepted that the fluid motion is caused by convection driven either by thermal buoyancy or by chemical buoyancy or by both. The chemical buoyancy is released upon the growth of an inner core. The latter requires a light alloying element in the core that is enriched in the outer core as the solid inner core grows. In most models, the light alloying element is assumed to be sulfur, but other elements such as, e.g., oxygen, silicon, and hydrogen are possible. The existence of cores in the terrestrial planets is either proven beyond reasonable doubt (Earth, Mars, and Mercury) or the case for a core is compelling as for Venus and the Moon. The Galilean satellites Io and Ganymede are likely to have cores judging from Galileo radio tracking data of the gravity fields of these satellites. The case is less clear cut for Europa. Callisto is widely taken as undifferentiated or only partially differentiated, thereby lacking an iron-rich core. Whether or not Titan has a core is not known at the present time. The terrestrial planets that do have magnetic fields either have a well-established inner core with known radius and density such as Earth or are widely agreed to have an inner core such as Mercury. The absence of an inner core in Venus, Mars, and the Moon (terrestrial bodies that lack fields) is not as well established although considered likely. The composition of the Martian core may be close to the Fe–FeS eutectic which would prevent an inner core to grow as long as the core has not cooled to temperatures around 1500 Kelvin. Venus may be on the verge of growing an inner core in which case a chemical dynamo may begin to operate in the geologically near future. The remanent magnetization of the Martian and the lunar crust is evidence for a dynamo in Mars’ and possibly the Moon’s early evolution and suggests that powerful thermally driven dynamos are possible. Both the thermally and the chemically driven dynamo require that the core is cooled at a sufficient rate by the mantle. For the thermally driven dynamo, the heat flow from the core into the mantle must by larger than the heat conducted along the core adiabat to allow a convecting core. This threshold is a few mW?m^?2 for small planets such as Mercury, Ganymede, and the Moon but can be as large as a few tens mW?m^?2 for Earth and Venus. The buoyancy for both dynamos must be sufficiently strong to overcome Ohmic dissipation. On Earth, plate tectonics and mantle convection cool the core efficiently. Stagnant lid convection on Mars and Venus are less efficient to cool the core but it is possible and has been suggested that Mars had plate tectonics in its early evolution and that Venus has experienced episodic resurfacing and mantle turnover. Both may have had profound implications for the evolution of the cores of these planets. It is even possible that inner cores started to grow in Mars and Venus but that the growth was frustrated as the mantles heated following the cessation of plate tectonics and resurfacing. The generation of Ganymede’s magnetic field is widely debated. Models range from magneto-hydrodynamic convection in which case the field will not be self-sustained to chemical and thermally-driven dynamos. The wide range of possible compositions for Ganymede’s core allows models with a completely liquid near eutectic Fe–FeS composition as well as models with Fe inner cores or cores in with iron snowfall.     

Investigation into the transient flow characteristics of noble gas propellants using the pulsed inductive discharge in electric propulsion

The Pulsed Inductive Thruster (PIT) has the advantages of repeatable startup, no corruption and in-situ propellant feed. To study the flow expansion and circuit characteristics of PITs, the circuit-fluid model is developed, and the high temperature thermodynamic and transport models are combined with the circuit-fluid model to predict the critical plasma parameters. The flow fields of initial mass of 2–8 mg and charge voltages of 10–14 kV are simulated. Comparison of the flow fields of argon and helium propellants suggests that, the flow field structures are similar. Slight differences exist on the magnitude of the density and magnetic field, caused by larger velocity in lighter atom case and difference on the ionization gap between adjacent ionization levels. Analysis of the circuit characteristics by the two-dimensional results indicates that the ratio of coil inductance to circuit inductance affects both the rise rate and phase of the plasma current, the larger the ratio, the greater the rise rate and the better the following characteristic. The calculations show that the magnetic energy obtained within the decoupling distance determines the overall performance the thruster can be obtained; self-induced field maintained by the thermal motion after the main pulse leads to the long attenuation process and difference on the total impulse when the angle of conical pylon is varied under constant coil dimension.     

A Closely Regulated TWT Converter

The design concept for the traveling wave tube amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics were utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power traveling wave tube (TWT), and at the same time operate at an efficiency of better than 90 percent from a 30-volt source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data is presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered. The circuit provides better than 0.5 percent regulation against load change, input voltage change, and over-operating temperature range of from -20 to + 80°C, with output ripple voltage of less than 2 volts peak-to-peak on top of the 3600-Vdc output. The measured efficiency was typically 87 percent. and recommendations are included to improve this to in excess of 90 percent.     

基于等效磁路法的轴向磁场磁通切换型永磁电机静态特性分析

轴向磁场磁通切换型永磁(AFFSPM)电机是一种轴向长度短、转矩密度高的新型永磁电机。该电机磁场呈三维分布,与径向磁场电机不同,需要对该电机进行三维有限元分析,从而增加了电机分析和优化时的计算时间和成本。基于等效磁路法分析了AFFSPM电机的静态特性,建立了AFFSPM电机的非线性等效磁路模型,采用该模型计算、分析了气隙磁密、空载永磁磁链、反电动势和电感等特性,并与采用三维有限元方法的计算结果进行比较,验证了AFFSPM电机等效磁路模型的准确性,表明等效磁路模型适用于AFFSPM电机初始设计和分析。     

宇航用小型化超稳晶振（USO）设计与实现

在分析高稳定晶体振荡器(OCXO)工作原理的基础上,提出了一种改善晶体振荡器相位噪声的方法.通过低噪声主振电路设计、高精度控温电路设计及机电一体化设计等措施,设计研制了一种宇航用小型化超稳定晶体振荡器(USO),尺寸为99mm×88mm×55mm.经测试,产品短期频率稳定度为2.11×10-13/1s、3.28×10-13/10s、8.61×10-13/100s(Allan方差),相位噪声为-129.4dBc/Hz@1Hz和-147.0dBc/Hz@10Hz.     

空心涡轮叶片精铸蜡型陶芯定位元件尺寸计算方法

 针对空心涡轮叶片精铸蜡型陶芯定位元件尺寸难以精确量化的问题,提出了基于模型匹配算法的陶芯定位元件尺寸计算方法。通过将壁厚权值因子引入匹配模型,实现了测量数据与理论模型的精确匹配;基于匹配后的陶芯实测数据,建立了定位元件的尺寸计算方法;最后,将壁厚偏差分布一致的一批陶芯分两组进行实验对比。结果表明该方法计算出的陶芯定位元件尺寸能够有效提高蜡型壁厚精度,对空心涡轮叶片的精确控型有一定的指导意义。     

高频高速流体振荡器工作特性

设计了一种新型高频高速流体振荡器,并采用热线风速仪、高频动态压力传感器等测量手段,对其频率-压力响应特性、速度-压力响应特性及内部压力传播特性进行了实验研究。结果表明:设计的流体振荡器工作频率约为900 Hz,进出口压比为2时,其出口射流速度范围为75~239 m/s。建立了振荡周期/频率与内部尺寸的关系式,验证了振荡器内部的压力传播与反射机制,并用压力的作用机制解释了射流偏转的两个阶段,为今后设计不同流动条件下所需的流体振荡器提供了设计思路。      

一种基于FPGA的ISA航空总线设计方法

Nios Ⅱ处理器是Altera公司推出的基于SOPC系统的嵌入式软核处理器。在Quartus Ⅱ软件的SOPC Builder工具中,用户可以利用Nios Ⅱ处理器、标准配套外围设备以及用户自定义的逻辑接口IP核来创建适用的Nios Ⅱ嵌入式系统,再将设计下载到Altera公司的FPGA中进行实现。本文在Quartus Ⅱ软件中使用Verilog硬件描述语言创建了基于Avalon总线的ISA总线接口逻辑,并在SOPC Builder中实现对此元件的封装,使之成为可供Nios Ⅱ系统使用IP核。     

高速开关磁阻电机用纳米晶定子铁心磁特性研究

以1台4/2极结构高速开关磁阻电机(SRM)为研究对象,研究纳米晶铁心磁特性及其对电机性能的影响。将采用叠块切割法制备的纳米晶定子铁心与传统硅钢冲片铁心做对比测试。搭建电机测试系统,对分别装配两种定子铁心电机的静态特性和负载运行性能做对比分析。结果表明:纳米晶合金铁心具有高磁导率、低矫顽力及低损耗特性,在1 kHz、1 T条件下,其损耗仅为35W300硅钢铁心的1/20;纳米晶合金铁心提高了SRM在铁心不饱和区的相电感峰值,并在转速25 000 r/min负载运行下显著降低了电机温升和输入功率。研究结果可为高效、高速SRM设计提供参考。     

基于超导的重力梯度敏感线圈电磁特性分析

为了利用超导块体的完全抗磁性与敏感线圈的电感变化测量重力梯度,需要对敏感线圈的电磁特性进行分析.利用盘状超导敏感线圈产生磁场,首先分析单匝线圈在场点产生的磁感应强度,再通过叠加得到场点的总磁感应强度.选取设计参数对线圈外小间距范围内的磁感应强度进行计算可知,径向分量沿线圈径向保持稳定值,而轴向分量变化较大.质量块对总磁...     

磁流变阻尼器磁路计算及磁通利用率分析

将分段等效磁路法应用于磁流变阻尼器的磁路计算。通过对磁路结构的综合分析,建立了磁流变阻尼器的分段等效磁路模型。采用网孔法建立了多分支复杂网络系统的非线性网络方程组。最后应用迭代法求解非线性网络方程组的磁通,计算了样机的磁通分布和磁通利用率。计算结果能够根据等效磁路模型的细分程度满足不同计算精度的需要,简化了磁路计算,具有较高的实用价值。     

Two-phase forward converter using an integrated magnetic component

An interleaved two-phase forward converter using an integrated magnetic component is proposed for telecommunication and computer applications. The integrated magnetic component consists of two step-down transformers and two output-filtering inductors on a single magnetic core. The z-parameter (gyrator) model and the equivalent-circuit model of the integrated magnetic component are presented. The circuit operation and design criteria of the proposed converter are described. All theoretical analyses are verified by simulated and experimental results.     

The effect of the magnetizing inductance on the small-signaldynamics of the isolated Cuk converter

The magnetizing inductance of the isolated Cuk converter introduces an undesirable pair of closely spaced complex zeros and poles, or a glitch, in the control-to-output transfer function. Limited analysis and experimentation in the past have shown that sufficient increase in the magnetizing inductance or manipulation of the ratio of the capacitances of the energy transfer capacitors can reduce the glitch. In this work, the isolated Cuk converter with coupled input and output inductors has been studied and the dependence of the glitch on various circuit parameters has been determined analytically. A condition has been derived for the ratio of the capacitances of the two energy transfer capacitors which completely eliminates the glitch at a given operating point. With this condition satisfied, it is shown that the energy transfer capacitors can be easily damped by a simple RC network to eliminate the glitch from a wide range of operation about an operating point     

面向多旋翼重载无人机均流技术优化研究CSCD

多旋翼重载无人机的应用需要大功率的无刷直流电机为其提供升力。金属-氧化物半导体场效应晶体管(MOSFET)和绝缘栅双极型晶体管(IGBT)等开关器件可以通过并联提供更大的电流容量,以满足大功率的需求。然而,由于杂散电感、器件特性的变化和印制电路板(PCB)布局的不对称等原因,并联开关器件将出现不平衡电流,这可能会对系统造成损坏。为解决此问题,使用Multisim软件搭建仿真电路,测量2个并联MOSFET之间的电流,分析不平衡电流产生的具体原因,并提出了一种采用栅极串联均流电阻联合耦合电感的MOSFET并联电流均衡方法,最后通过仿真和实验验证了该方法的可行性。与串联均流电阻法和耦合电感法相比,此方法能使导通电流保持均衡,更好地提高系统的可靠性。     

Table-Aided Design of the Energy-Storage Reactor in DC-to-DC Converters

A new procedure for the selection of magnetic cores for use in energy-storage dc-to-dc power converters that eliminates the need for an automated computer search algorithm and stored data file is presented. The converter configurations included in the procedure are the three commonly encountered single-winding converters for voltage stepup, for current stepup and voltage stepup/current stepup, and for the two-winding converter for voltage stepup/current stepup. For each converter configuration, three types of controllers are considered: constant-frequency, constant on-time, and constant off-time. Using concepts developed from analyses of these converters by considering the transfer of energy by means of an energystorage inductor or transformer, a special table of parameters calculated from magnetic core data is constructed, which leads to a considerably simplified design procedure.     

基于不同定子槽模型的分段磁路分析

结合等效磁场实现转子内磁场强度至转子轭表面的转换,分别建立了开口、半开(闭)口定子槽模型,采用分段磁路法分析各段磁路长度变化情况,给出了不同定子槽模型下齿槽转矩的解析式。分析定子冲片选用不同牌号的硅钢片材料对齿槽转矩的影响。经研究表明:分段磁路法能够提高槽间磁路近似精度,且经分析优选的定子硅钢片材料可较为有效地削弱齿槽转矩。     

旋转变频频率捷变雷达本振跟踪误差的分析

 本文从旋转变频磁控管式频率捷变雷达的本振频率跟踪原理出发,分析了产生本振频率跟踪误差的主要因素。文中着重讨论了本振频率冷跟踪误差问题。同时也提出了热跟踪后本振频率跟踪误差项。分析前者,可以决定热跟踪电路应予修正的频率范围,而后者则是跟踪本振最终的误差。以上分析对如何采取措施提高系统的跟踪精度是有参考作用的。