共查询到20条相似文献,搜索用时 185 毫秒
1.
热控涂层参数对卫星辐射特性的影响 总被引:1,自引:0,他引:1
为分析卫星红外和可见光双光谱辐射特性,分别建立了采用节点网络法求解卫星表面热控涂层温度和卫星辐射特性的计算模型,依据粗糙表面光散射理论计算了涂层表面对太阳、地球和地球反照辐射的吸收和反射。通过数值模拟,计算分析了卫星对地面的温度变化规律。最后,选择不同的热控涂层参数,获得了对卫星在红外和可见光波段的辐射特征的影响。 相似文献
2.
3.
4.
5.
6.
7.
用FVM法计算固体火箭羽流的红外特性 总被引:9,自引:2,他引:9
建立了有限体积法(FVM)的理论模型模拟固体火箭羽流的红外特性,研究了燃气组分H2O,CO2,CO,HCL,OH,NO的吸收和发射,以及AL2O3粒子云的吸收、发射和散射,还研究了两相流场中气相和粒子云温度不均匀时对辐射传输方程的修正。计算一单喷管固体火箭的二维轴对称羽流在光谱2~5μm的红外特性,给出羽流辐射的空间分布和光谱分布并与文献计算的结果对比。研究表明:有限体积法能较好地模拟固体火箭羽流的红外特性;粒子辐射占固体火箭羽流红外辐射的主要部分;在光谱2~4μm粒子辐射使羽流辐射增强,而在光谱4~5μm粒子辐射使羽流辐射减弱。 相似文献
8.
着陆冲击仿真月壤本构模型及有限元建模 总被引:1,自引:0,他引:1
为建立合理的月壤有限元模型用于着陆器着陆冲击动力学仿真分析,在对已知月壤的相关力学特性参数和试验数据进行分析推理的基础上,推断出月壤屈服面在低围压条件下可能会呈现出剪切膨胀特性,而在高围压条件下则可能会呈现出塑性压缩和应变硬化特性,因此定性地选择帽盖德鲁克-普拉格(Cap Drucker-Prager,CDP)模型作为月壤本构模型。模型的参数通过月壤或模拟月壤的试验数据定量地标定。对着陆器地面着陆冲击试验进行有限元建模和仿真分析,仿真结果表明:模型参数的标定方法是合理可行的;CDP模型可以准确模拟月壤在着陆冲击载荷下的动力学响应,可用于着陆冲击动力学仿真月壤有限元建模。对月壤模型参数进行了参数分析,并评估了月壤模型参数对着陆器着陆冲击性能的影响。 相似文献
9.
月球表面及月壤内温度分布特征的数值模拟 总被引:1,自引:1,他引:0
文章建立了月表辐射与月壤内二维非稳态导热的耦合传热模型,采用控制容积法数值模拟月壤内的温度分布,主要研究了月表、月壤内温度的分布和变化规律及探测器对局部月表温度的影响。计算结果表明一昼夜期间月壤内存在明显的温差:浅层月壤处的昼夜温差较大且受纬度的影响明显;随着深度的增加,月壤昼夜温差降低并趋于稳定,且受纬度的影响较小。探测器的存在遮挡了月表接受的太阳辐射,导致其阴影区域内月表温度发生突变,新的平衡温度接近探测器底面温度,且受探测器驻留时间的影响较小;当探测器移开,月表温度又迅速恢复到原有的变化规律。 相似文献
10.
文章通过常规3轴试验对某模拟月壤的本构特性进行了研究,根据3轴试验结果获得了模拟月壤的duncan-chang模型参数,在abaqus软件平台上通过umat子程序实现了duncan-chang模型在模拟月壤分析中的应用,并进行了相应的试验验证.之后,文章就内摩擦角、粘聚力参数变化时模拟月壤剪切变形关系的变化及低围压下自重应力对模拟月壤性质的影响进行了仿真分析,结果发现和内摩擦角、粘聚力等参数相比,初始自重应力对模拟月壤的剪切特性影响不大. 相似文献
11.
12.
13.
When lunar modules land on the Moon, dust impingement on the lunar module components and deposition on the thermal and optical surfaces would cause many serious problems. The emphasis of this research is on simulating the interaction of rocket plume and lunar dust using the direct simulation Monte Carlo (DSMC) method. The method is extended to model the movement and collision stages of rarefied plume gas and dust particles, including three collisional mechanisms: molecule–molecule, molecule–particle and particle–particle collisions. The reflection of gas molecules on the particle surface is computed by an indirect approach based on the coordinate transformation. Neighboring-cell contact detection scheme is applied to check for contacts between all possible particle pairs. The simulation results show that the acceleration of dust particle is mostly determined by the parameters of plume field. In the computational regions with larger gas density and velocity the particles can be accelerated to larger velocity and convected to higher temperature. 相似文献
14.
扬起的月尘颗粒沉积在月球探测器的太阳电池表面,可导致其性能下降。文章基于层叠遮挡理论,建立了一种月尘遮蔽光线透射的理论模型,利用该模型开展了模拟月尘颗粒形状与粒径对遮蔽效果影响的分析和计算,并与NASA的同类模型进行了对比分析。分析结果显示:2种模型给出的相对透过率随沉积月尘面密度的变化趋势相同,均呈指数型衰减关系;在随月尘形状、粒径、透过率的变化方面,2种模型存在差异。利用月尘沉积与吸附试验装置实施了模拟月尘沉积试验,验证了所建立模型的正确性,其预测准确度优于NASA模型。 相似文献
15.
16.
3D-printing technologies are receiving an always increasing attention in architecture, due to their potential use for direct construction of buildings and other complex structures, also of considerable dimensions, with virtually any shape. Some of these technologies rely on an agglomeration process of inert materials, e.g. sand, through a special binding liquid and this capability is of interest for the space community for its potential application to space exploration. In fact, it opens the possibility for exploiting in-situ resources for the construction of buildings in harsh spatial environments. The paper presents the results of a study aimed at assessing the concept of 3D printing technology for building habitats on the Moon using lunar soil, also called regolith. A particular patented 3D-printing technology – D-shape – has been applied, which is, among the existing rapid prototyping systems, the closest to achieving full scale construction of buildings and the physical and chemical characteristics of lunar regolith and terrestrial regolith simulants have been assessed with respect to the working principles of such technology. A novel lunar regolith simulant has also been developed, which almost exactly reproduces the characteristics of the JSC-1A simulant produced in the US. Moreover, tests in air and in vacuum have been performed to demonstrate the occurrence of the reticulation reaction with the regolith simulant. The vacuum tests also showed that evaporation or freezing of the binding liquid can be prevented through a proper injection method. The general requirements of a Moon outpost have been specified, and a preliminary design of the habitat has been developed. Based on such design, a section of the outpost wall has been selected and manufactured at full scale using the D-shape printer and regolith simulant. Test pieces have also been manufactured and their mechanical properties have been assessed. 相似文献
17.
在对月球采样返回任务需求及探测器系统任务剖面进行分析的基础上,设计并研制了一种轻量化、大负载、高精度、宽采样范围月球采样机械臂系统。该系统主要由4自由度机械臂及两种不同采样形式的末端采样器组成,可对不同指定区域浅层月壤进行铲、挖、浅钻等多形式采集。在综合考虑机械臂系统器上布局的基础上,基于运动学模型对采样机械臂的可达采样区域进行仿真分析,提出采样机械臂月面采样策略。基于等尺寸着陆器模拟平台,开展了针对3种不同密实度模拟月壤的采样试验,采样试验结果表明在可达采样空间内,采样机械臂对不同密实度月壤均具有较好的适应性,最大采样深度可达30 mm,最大单次采样量可达270 g,单次采样时间小于2 min。 相似文献
18.
为分析光伏电池玻璃表面微织构形状和颗粒碰撞方式对表面微织构损伤的影响,建立模拟月尘颗粒碰撞表面微织构仿真模型,结合实验验证,探究表面微织构损伤情况。结果表明:30 μm直径的模拟月尘颗粒以5 m/s的速度撞击表面微织构时,损伤形式主要包括边缘破损、劈裂破损和断裂,损伤面积与表面微织构整体相比较小,损伤深度在0.06~0.29 μm之间,仅为表面微织构柱体高度的1%~4.8%;中心正碰时,四棱台表面微织构的抗冲击性最好,圆台表面微织构次之,六棱台表面微织构最差;颗粒以4种碰撞方式撞击圆台表面微织构时,损伤程度从大到小依次为边缘碰撞、45°边缘碰撞、中心正碰、45°中心碰撞。研究结果可为玻璃表面微织构的工艺改性提供参考。 相似文献
19.
模拟月尘对巡视器车轮轮轴材料的磨损试验研究 总被引:2,自引:2,他引:0
文章以CE-3巡视器车轮轮轴为研究对象,利用北京卫星环境工程研究所的月尘环境模拟器、摩擦磨损试验机以及自行研制的模拟月尘,对车轮轮轴主要材料进行了磨损试验研究。试验样品为轮轴常用的铝合金、聚四氟乙烯及轴承钢。文章分析了试验前后样品的表面形貌,采用测试系统获得了轮轴材料在不同试验条件下的摩擦系数曲线,采用电子天平测量了材料的质量损失;分析了真空、大气、有无月尘等试验条件以及材料本身在磨损试验中的效应。研究结果可为月面巡视器等月面应用设备的研制提供可借鉴的信息。 相似文献
20.
文章针对未来有人参与的月球探测任务,首先开展了月球表面环境地面模拟试验验证需求分析,归纳总结了国内外技术发展现状。然后,提出并分析了载人月球探测地面模拟试验需重点研究的关键技术:真空热环境下月面移动式多体低重力模拟技术;复杂月面环境高精度热流模拟技术;大容量布尘条件下超高真空获得与保持技术;月面辐射与月尘环境模拟技术;月尘防护效能量化评估技术;月面综合环境试验验证技术等。最后,给出了面向载人月球探测的月面环境模拟试验技术研究总体方案,并对月面环境模拟试验技术的发展目标进行了展望。 相似文献