多相等离子体气动激励抑制翼型失速分离的实验

开展了多相等离子体气动激励抑制NACA0015翼型失速分离的实验,详细研究了翼型升阻特性随激励电压、激励相角、输入电压波形和占空比等激励参数的影响.研究表明:雷诺数Re=4.9×105(来流速度60m/s)时,多相等离子体气动激励可有效抑制NACA0015翼型吸力面的流动分离,将翼型临界失速攻角提高2°;相位对流动控制...     

合成射流方向布局对S形进气道分离控制的效应

对合成射流控制一种S形进气道边界层分离进行了数值研究.选用狭缝出口的合成射流,详细讨论了展向和流向两种布局对控制效应的影响.结果显示:流向布局相对展向布局具有抗逆压梯度强、穿透深、控制效果持久等特点,在射流动量系数为1.62×10-3,特征频率等于1的工况下,其分离区长度缩减了38.39%.流向布局对S形进气道性能的提升也更显著,出口压力系数比无控制时提高158.91%,总压恢复系数提高0.71%,总压畸变指数降低56.75%.      

合成双射流控制翼型分离流动的数值研究

合成双射流激励器是合成射流技术发展的最新成果,所形成的射流具有更高能量、流动更稳定的特点。采用数值模拟的方法,对比研究了合成射流与合成双射流对翼型分离流动的改善效果。结果表明:合成射流可以将翼型失速攻角提高2°、最大升力系数增加18%,合成双射流可以将翼型失速攻角提高4°、最大升力系数增加35%,证明了合成双射流具有更好的分离流动控制效果。另外着重分析了合成双射流工作频率和动量系数对控制效果的影响,发现当激励器工作频率为流场特征频率的1和2倍时,对翼型气动特性的改善效果最好,同时控制效果会随动量系数的增加而增大。     

Suppressing unsteady motion of shock wave by high-frequency plasma synthetic jet

Three Plasma Synthetic Jet Actuators (PSJA) under the high-frequency actuation are used to control the Shock Wave Boundary Layer Interaction (SWBLI), a high-speed schlieren image processing method based on spatial Fourier transform as well as snapshot proper orthogonal decomposition were used to study the control effect of high-frequency plasma synthetic jet on low-frequency unsteadiness of SWBLI. The analysis of the base flow shows that the separated shock wave actually has both large- and small-amplitude vibrations at low frequency. And the results revealed that the PSJA with an operating frequency of 2 kHz has the ability to reduce the energy of low-frequency component of shock wave motion, indicating that the 2 kHz actuation can effectively suppress low-frequency unsteadiness of the separated wave. Compared with the actuation frequency of 2 kHz, the energy of low-frequency component of the shock wave is enhanced under the 8 kHz actuation, which aggravates the low-frequency unsteady motion of the shock wave. It is likely that the actuation frequency is too high, thus the intensity of the precursor shock wave induced by PSJA becomes weaker. Additionally, as the 4 kHz actuation is applied, the pulsation of the separation region was enhanced, it is speculated that the actuation frequency is coupled with the oscillation frequency of the separation region.     

合成射流控制高速扩压叶栅二次流的数值模拟

数值研究了合成射流控制高速扩压叶栅角区分离,并揭示其推迟分离、降低损失的作用机理。研究发现:合成射流可以显著改善叶栅内流场的时空结构,叶栅出口时均总压损失系数最大降低19.8%,静压系数也提高了近8.8%。合成射流通过周期性地吹/吸气有效控制角区分离,吹气阶段的高动量射流流体增大了吸力面附面层及角区流体的能量,吸气阶段则借助于附面层抽吸作用有效减少了高熵、低能流体的堆积,从而增强了角区流体抵抗流向逆压力梯度的能力、并推迟流动分离,且吸气阶段的流动控制效果明显更好。射流角度和射流动量是影响合成射流作用效果的重要参数,近切向的合成射流有利于向附面层注入动量,增大射流动量也有助于增强流动控制效果。析因设计研究表明,射流角度的影响效应更为显著,但与射流动量之间并不存在交互作用。      

射流对压气机叶栅分离流控制的数值研究

现代先进轴流压气机级负荷不断提高的发展趋势导致流动分离日益严重.借助数值模拟分别对非定常射流和定常射流进行了参数优化研究.结果表明:基于射流的主动流动控制能有效弱化或消除流动分离,不同射流方式存在不同的最优射流参数(射流方向、位置、速度和频率等),这就为利用射流控制轴流压气机分离流动的工程应用奠定了一定的理论基础.     

等离子体气动激励抑制机翼失速分离的实验

进行了等离子体气动激励抑制机翼失速分离的风洞实验,研究了等离子体气动激励频率、电压、占空比和激励位置等对流动控制效果的影响.研究表明:在来流速度35m/s时,等离子体气动激励可以有效地抑制机翼大攻角下吸力面的流动分离,将机翼临界失速迎角由17°提高到19°;施加激励后,机翼最大升力系数提高了9.45%,阻力系数减小20.9%;激励频率在200Hz时,控制效果最好,对应的量纲一激励频率为1;迎角越大,流动分离越严重,需要更大的激励电压才能够有效抑制流动分离;最佳激励位置在流动分离起始点的前缘;在流动控制效果相当时,减小占空比可以降低能耗.      

Leading-edge flow separation control over an airfoil using a symmetrical dielectric barrier discharge plasma actuator

In order to promote an in-depth understanding of the mechanism of leading-edge flow separation control over an airfoil using a symmetrical Dielectric Barrier Discharge(DBD) plasma actuator excited by a steady-mode excitation, an experimental investigation of an SC(2)-0714 supercritical airfoil with a symmetrical DBD plasma actuator was performed in a closed chamber and a low-speed wind tunnel. The plasma actuator was mounted at the leading edge of the airfoil.Time-resolved Particle Image Velocimetry(PIV) results of the near-wall region in quiescent air suggested that the symmetrical DBD plasma actuator could induce some coherent structures in the separated shear layer, and these structures were linked to a dominant frequency of f0= 39 Hz when the peak-to-peak voltage of the plasma actuator was 9.8 kV. In addition, an analysis of flow structures without and with plasma actuation around the upper side of the airfoil at an angle of attack of18° for a wind speed of 3 m/s(Reynolds number Re = 20000) indicated that the dynamic process of leading-edge flow separation control over an airfoil could be divided into three stages. Initially, this plasma actuator could reinforce the shedding vortices in the separated shear layer. Then, these vortical structures could deflect the separated flow towards the wall by promoting the mixing between the outside flow with a high kinetic energy and the flow near the surface. After that, the plasma actuator induced a series of rolling vortices in the vicinity of the suction side of the airfoil, and these vortical structures could transfer momentum from the leading edge of the airfoil to the separated region, resulting in a reattachment of the separated flow around the airfoil.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

Separation control on NACA23012 using synthetic jet

A numerical study of separation control has been made to investigate aerodynamic characteristics of NACA23012 airfoil with synthetic jets. Computed results demonstrated that stall characteristics and control surface performance could be substantially improved by resizing separation vortices. The maximum lift was obtained when the separation point coincides with the synthetic jet location and the non-dimensional frequency is about 1. In addition, separation control effect was proportional to the peak velocity of the synthetic jet. It was observed that the actual flow control mechanism and flow structure is fundamentally different depending on the range of synthetic jet frequency. For low frequency range, small vortices due to synthetic jet penetrated to the large leading edge separation vortex, and as a result, the size of the leading edge vortex was remarkably reduced. For high frequency range, however, small vortex did not grow up enough to penetrate into the leading edge separation vortex. Instead, synthetic jet firmly attached the local flow and influenced the circulation of the virtual airfoil shape which is the combined shape of the main airfoil with the separation vortex. As a way to reduce the jet peak velocity, performance of a multi-array synthetic jet was investigated. Moreover, a high frequency multi-location synthetic jet was exploited to efficiently eliminate the unstable flow structure which was observed in low frequency range. Finally, by changing the phase angle in multi-location synthetic jets, highly controlled flow characteristics could be obtained with multi-array/multi-location synthetic jets. This shows efficiency of the current approach in separation control using synthetic jet.     

来流湍流度对超高负荷低压涡轮附面层流动控制手段的影响

实验研究了表面粗糙度耦合上游尾迹的流动控制技术,分析了来流湍流度（FSTI）在流动控制过程中对叶片吸力面附面层分离、转捩特性的影响.实验发现:在速度峰值点至分离点之间布置粗糙高度与弦长之比为1.05×10-4的粗糙条带可以在来流湍流度为0.4%与2.2%的低雷诺数范围内降低叶型损失.在雷诺数为85000的状态下,FSTI影响了尾迹通过区、尾迹诱导转捩区及自然转捩区的附面层动量厚度,造成了叶型损失的差异,但FSTI对抑制区的影响较小.      

翼型分离流动主动控制实验

设计制作了两种布局形式的压电式合成射流致动器, 采用热线风速仪在静止环境下对长方形喷口的速度场进行了测量, 结果表明致动器喷口法向喷出最大速度可达到21.32 m/s.开展了基于合成射流技术的翼型分离流动主动控制实验, 致动器采用倾斜喷出时速度为10 m/s量级, 有效推迟了翼型表面流动的分离, 改善了翼型的失速特性, 最大升力系数提高11.36%, 失速迎角增加3°.与此同时发现动量系数达到10-3量级时分离流动主动控制效果显著, 动量系数小于10-4量级分离流动控制将几乎没有效果.      

基于合成射流的二维后台阶分离流主动控制

作为一种新的流动控制激励器,合成射流技术在流动分离控制、降低压力脉动和抑制噪声等方面具有广阔的应用前景。实验利用合成射流主动控制技术对二维后台阶湍流分离再附流动控制进行了研究,应用表面测压、粒子图像测速(PIV)和热线等多种实验测试技术对后台阶表面压力分布、流场结构以及剪切层特性进行了测试。结果表明,在台阶前缘施加合成射流可有效减小回流区范围和降低再附长度,当合成射流的动量系数为0.301×10^-3时,可使再附点长度减小25%。合成射流控制使得沿台阶下游的湍动能和雷诺应力增强,提高了台阶下游流场的混合效率。热线动态结果表明频率是后台阶分离流动控制的关键参数,当频率为260 Hz、激励频率与剪切层涡脱落频率之比为1.32、激励频率等同于旋涡脱落频率时,合成射流控制效果最好,仅需消耗较小的能量即可实现流动控制的目的。     

Effects of coarse riblets on air flow structures over a slender delta wing using particle image velocimetry

This research investigates the aerodynamic performance and flow characteristics of a delta wing with 65° sweep angle and with coarse axial riblets,and then compares with that of a smooth-surface delta wing.Particle Image Velocimetry(PIV)were utilized to visualize the flow over the wing at 6 cross-sections upright to the wing surface and parallel to the wing span,as well as 3 longitudinal sections on the leading edge,symmetry plane,and a plane between them at Angles of Attack(AOA)=20°and 30°and Re=1.2×10~5,2.4×10~5,and 3.6×10~5.The effects of the riblets were studied on the vortices diameter,vortex breakdown location,vortices distance from the wing surface,flow lines pattern nearby the wing,circulation distribution,and separation.The results show that the textured model has a positive effect on some of the parameters related to drag reduction and lift increase.The riblets increase the flow momentum near the wing’s upper surface except near the apex.They also increase the flow momentum behind the wing.     

Numerical investigation on flow mechanism in a supersonic fluidic oscillator

A type of supersonic fluidic oscillator is proposed and its ability to generate pulsating supersonic jet is proved in this paper. Unsteady two-dimensional numerical simulations reveal that the fluid transforms from subsonic to supersonic condition in the mixing chamber of oscillator after the supplied flow pressure increases from 1.1 × 10⁵ Pa to 5.0 × 10⁵ Pa. When the supersonic flow is formed inside the oscillator, the wall-attached flow represents expansion wave and compression wave alternately. The oscillating frequency will saturate to a certain value with the increase of supplied pressure. Examination of the internal fluid dynamics indicates that the flow direction inside the FeedBack Channel (FBC) is related to the change of the local pressure at the inlet and the outlet of the feedback channel. The vortices produced in the mixing chamber present different distribution characteristics with the change of the fluid’s direction in the FBC. The sweeping jet is divided into two jets with varying flow rate over time by the splitter. In the end of two channels, two jets are accelerated above sound speed by convergent-divergent nozzle. Therefore, pulsating supersonic jets are produced at two outlets for this type of fluidic oscillator.     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

合成双射流控制NACA0015翼型大攻角流动分离试验研究

设计了一种卧式合成双射流激励器(DSJA),并对其在翼展中段控制NACA0015翼型大攻角流动完全分离进行试验研究,分析了合成双射流激励器两射流出口位置及射流能量对控制机翼流动分离的影响规律。结果表明:合成双射流激励器对机翼大攻角流动分离具有很强的控制能力,可显著提高机翼流动分离攻角;合成双射流激励器两射流出口相对分离点的位置是影响控制效果的重要参数;合成双射流激励器两出口任一出口位于分离点之前,且越靠近分离点,其对边界层分离的控制效果越好,并且当分离点位于合成双射流激励器两出口之间,且离第一出口位置较近时,合成双射流"接力"控制机翼分离的效果更加明显;与合成射流"单射流"相比,合成双射流"两射流"对分离点位置的有效控制区域明显增大。此外,提高合成双射流激励器的射流能量,其控制机翼流动分离的能力提高。     

非对称出口合成双射流激励器矢量特性实验研究

合成双射流(DSJ)激励器由于自身具有独特的矢量控制特性,为合成射流技术应用于主动流动控制提供了新途径。采用了基于射流核心区速度矢量的评价方法,并通过纹影和粒子图像测速法(PIV)流场显示实验研究了非对称出口压电式合成双射流激励器驱动参数(电压和频率)对射流矢量特性的影响。结果表明:合成双射流向出口面积大的一侧偏转,矢量偏转角随电压变化呈现先增大后减小的趋势,存在一个最佳驱动电压幅值,使得矢量偏转角最大;驱动频率变化对矢量偏转角的影响较显著,其对射流矢量的控制机理较复杂,实现矢量偏转角1.53°~36.65°可调,矢量偏转角出现两个峰值,且在振动膜共振频率处,矢量偏转角最小。     

基于NURBS曲线的涡控蛇形进气道设计

利用NURBS(non-uniform rational B-spline)曲线成功实现了涡控蛇形进气道参数化描述,并运用数值仿真方法对其中两个关键设计参数进行参数化研究.仿真结果表明:①第二S弯上壁面两侧后掠状凸起型面诱导的受控旋涡能够将低能流牵引至出口两侧,从而抑制大范围的气流分离,但凸起角取值需权衡选取,否则将不利于涡控蛇形进气道综合性能的改善.②通过抬高第二S弯下壁面能够减缓上壁面沿程逆压力梯度,进而影响第二S弯上壁面的流态,恰当的取值能够以微小的总压损失换取大幅度的畸变改善.③当设计参数选取恰当时,涡控蛇形进气道在设计状态下总压恢复系数为0.9667,畸变指数为0.2451.进气道性能较传统方案有显著改善,使得蛇形进气道迈向工程实用成为可能.      

等离子体激励控制激波与边界层干扰流动分离数值研究

针对高超声速进气道激波与边界层干扰流动分离控制问题,提出了一种低功率重频非定常激励方式,并基于雷诺平均Navier-Stokes(N-S)方程,从唯象学的角度出发,将等离子激励简化为功率密度源项,对比研究了定常与低功率重频非定常等离子体气动激励的作用机理与控制效果。结果表明:定常激励的能量沉积作用对于激波控制非常有效,并可诱导出斜激波,但是对于流动分离控制而言,其能量沉积显然过于强大,反而会使流动分离更加严重,无法满足控制要求;当采用低功率重频非定常激励方式时,对于不同功率密度的情况均存在最佳激励时长与频率,当功率密度为5.0×109W/m3时,最大射流速度可以达到895m/s,并且可以在一定程度上减弱激波与边界层干扰流动分离。