陀螺仪漂移伺服法测试的设备误差分析与补偿

分析了伺服法测试的误差源以及误差源对测试结果的影响,建立了设备误差与测试结果之间关系的数学模型,并给出了数学模型中主要误差的补偿方法,实验结果证明:补偿后测试精度显著提高。     

激波风洞气动力试验不确定度影响因素分析

参考北大西洋公约组织和AIAA推荐的风洞试验数据不确定度计算方法，结合激波风洞运行特点，确定激波风洞气动力试验的主要误差源，计算激波风洞13-2标模气动力测量结果的不确定度。采用改变单一变量的方法计算主要误差源对测量结果不确定度的影响程度，辨析对不确定度起主要作用的基本参数。计算结果表明：皮托压力和总压的测量结果对流场参数影响显著，皮托压力的测量结果比总压测量结果对流场参数与气动力测量结果影响更大；降低皮托压力和总压的偏离极限，有利于提高激波风洞气动力试验数据的质量。     

捷联寻的制导系统弹体追踪导引方法研究

对捷联寻的系统的简易制导方法—弹体追踪法进行全面剖析 ,解析分析了弹体追踪法对导弹速度、目标速度的约束 ,以及弹体阻尼、滞后、舵偏到攻角之间的传递系数对弹体追踪导引性能的影响。通过数学推导及应用控制理论分析与仿真 ,弹体追踪法较比例导引和速度追踪法在导引特性和打击机动目标时性能较差 ,但其成本较低 ,是一种降低制导武器成本的简易制导方法。但采用弹体追踪法时 ,导弹和目标的速度不能太大 ,当制导武器系统在形成导引误差信号存在固有滞后时 ,弹体稳定回路需要有一定阻尼 ,且舵偏到攻角之间的传递系数不能太大 ,即飞行过程中攻角要较小。     

空间交会对接调相轨道误差特性分析

分析空间交会对接目标航天器和飞船的轨道特性,针对同一发射地点先后发射两个航天器进行交会对接的方式,开展目标航天器调相轨道特性研究,并在.轨道预报相位误差特性分析的基础上,讨论目标航天器调相变轨策略和轨道预报精度需求。针对空间交会对接地面导引段开展飞船轨道特性研究,在霍曼转移轨道特性分析基础上.讨论一般转移轨道特性,分析飞船地面导引段终点状态对转移轨道的影响,并结合地面导引段研究轨道设计要素与飞船地面导引段终点状态的关系,分析轨控误差和预报误差对地面导引误差的影响。     

静压源误差修正及其在大气数据计算机的应用

 静压源误差直接影响飞机战术性能的发挥,是飞机设计、大气数据计算机研制及飞行试验面临的重要课题之一。本文从工程实践角度出发,分析静压源误差及其影响因素,以及静压源误差的修正。     

富氢/富氧燃气同轴剪切气-气喷嘴性能仿真分析

采用正交试验设计方法对富氢/富氧燃气同轴剪切气-气喷嘴设计参数氧压降比、燃氧速度比、氧喷嘴出口壁厚进行组合,数值模拟单喷嘴燃烧室燃烧流场,研究喷嘴设计参数及参数之间的交互作用对燃烧性能和燃烧室热载性能的影响,评价指标为燃烧长度、燃烧室壁面平均燃气温度和喷注面板平均燃气温度.仿真结果表明,燃氧速度比对燃烧与热载有显著影响,氧压降比与氢氧燃氧速度比的交互作用影响明显,分析结果对气-气喷嘴试验设计有重要指导意义.      

框架类远距离浅孔同轴度误差测量方法的探讨

讨论了利用三坐标测量机,测量框架类零件远距离浅孔同轴度误差的方法,分析了各种测量方法之间的区别,给出了一种适合框架类远距离浅孔公共轴线的测量方法.     

现代战机最佳导引算法研究

针对现代战机向目标空域的导引过程,建立了载机与目标相对运动的数学模型。基于最优控制的相关理论,以导引的准确性和控制的经济性为性能指标,建立了飞机导引控制算法。该导引算法既考虑了导引的角度误差又考虑了目标线角速度误差,通过对所得到的导引算法进行仿真验证,表明所得到的导引算法具有较强的适应性,能够满足飞机的导引要求。     

金属壳谐振陀螺误差补偿方法研究

针对金属壳谐振陀螺的误差建模与补偿方法进行研究.首先,通过分析金属壳谐振陀螺的敏感机理,找到影响陀螺性能的误差源,建立金属壳谐振陀螺的误差模型.然后,研究陀螺的误差传播特性,对误差源进行分类,提出金属壳谐振陀螺的误差补偿方法.最后,利用试验方法对建立的误差模型和补偿方法进行验证.试验结果表明:经过补偿后的金属壳谐振陀螺在工作温度范围内(-45℃ ～55℃)零偏不稳定性降低至4.67(°)/h,全温度段线性度由0.2％降低至0.03％,随机游走为0.6982(°)/h1/2,陀螺的综合性能得到显著提升,证明了误差模型和补偿方法的有效性.     

捷联航姿传感器的误差补偿标定方法

磁航向传感器作为机载设备,它的工作情况与载体环境的影响有着密切的关系,测得的磁航向角存在着较大的误差,不能直接用来进行导航定位。所以,必须对其进行误差补偿,提高磁航向角的测量精度,才能用于导航定位。罗差是磁阻罗盘的主要误差源,文中介绍了罗差方程式,并重点推导了基于最小二乘法的七参数八位置误差标定方法。基于该方法的磁航向补偿算法的性能试验结果证明,磁航向误差基本维持在0.5°左右,满足了精度的要求。     

交会对接远程导引轨道控制状态规划与优化算法

对空间交会对接远程导引段轨道控制问题进行了研究。在简单介绍交会对接远程导引轨道控制实时规划模型的基础上,提出了基于近圆偏差方程、序列二次规划算法和目标权重函数等在不同控制目标模式下的状态规划与优化算法。仿真结果表明,该算法收敛速度快,能较好地满足交会对接远程导引段的轨道控制要求,具有一定的工程实用价值。     

航天器快捷交会技术分析

快捷交会对航天乘员与飞行任务都是非常有利的。快捷交会的基本原理是减少调相段飞行圈数;为此,需设计可完成一系列交会程序的较短的飞行时间,并获得与飞行时间相匹配的较小的初相角。快捷交会的关键技术包括提高入轨精度,增强追踪飞行器的自主计算与轨道控制能力,扩大地面站覆盖范围,以及对目标飞行器轨道的精准调整。     

一种用于空间交会绕飞与逼近段的模糊控制律

研究了空间交会绕飞与最后逼近段的控制问题,设计出一种用于实现绕飞与逼近控制的模糊控制方案。在考虑测量误差的情况下,分别利用最小二乘与卡尔曼滤波方法对测量数据进行优化处理,并采用模糊控制方案实现绕飞与逼近段的仿真,仿真结果证实了模糊控制算法控制精度可以满足交会任务的需要,也验证了在具有测量误差条件下不同仿真方案所采用的模糊控制策略的有效性。     

基于信息一致性的无人机紧密编队集结控制

提出了基于信息一致性的分段式无人机紧密编队集结控制策略,将集结过程分为3步:参考集结点选取和目标集结点分配、形成松散编队以及形成紧密编队。首先,以线切入预定航线的方式计算参考集结点,按照松散编队队形展开生成目标集结点,并利用基于三维距离空间的优化选择算法,将目标集结点快速、准确地分配给每架无人机。然后,使用速度一致性实现向目标集结点定点集结和向松散编队伴航集结,通过非精确的航迹控制快速形成松散编队,提高编队集结的效率。接下来,启动速度、姿态一致性来实现编队最终的精确航迹控制,并逐步压缩编队队形进入紧密编队,避免发生碰撞,完成从松散编队到紧密编队的平稳过渡,同时准确地跟踪预定航线。使用协同修正方法抑制了测量误差、协同误差和通信延迟,提高了紧密编队的稳定性和控制精度。最后,基于MATLAB平台环境对所提三维集结控制策略进行了仿真,验证了其合理性与有效性。     

Accurate and autonomous navigation for the ATV

The Automated Transfer Vehicle (ATV) is a European spacecraft intended to service the International Space Station (ISS). It is designed to perform automated phasing, approach, rendezvous and docking to the ISS, then departure and deorbitation manoeuvres. Such an automated rendezvous mission towards a manned facility raises severe performance and safety constraints for the vehicle, which are declined towards the on-board Navigation in terms of availability, accuracy and failure tolerance: the ATV shall be operational after any first failure and safe conditions shall be reached after a second failure. The whole ATV navigation system has been designed to fulfil these very stringent requirements. Based on fully redundant hardware, the navigation algorithms present optimal estimators and multi-layers Failure, Detection, Isolation and Recovery (FDIR) capabilities to ensure the continuity of the state vector in case of failure. Several functions provide state vectors estimations and health reports, according to the flight phase: the attitude and drift estimation function provides the vehicle absolute attitude and angular rate during the whole flight; for the far rendezvous, position and velocity relative to the ISS are estimated by the relative GPS navigation and a dedicated relative navigation with Videometer applies in close rendezvous, in the final approach. All these autonomous navigation functions offer nevertheless a high level of monitoring and control to the ATV Control Centre operators. Thus the ATV innovative navigation chain provides the high level of performance, robustness and autonomy required by modern spacecrafts involved in human programs, today in Earth orbit but also for future space exploration missions.     

Rendezvous phasing special-point maneuvers mixed discrete-continuous optimization using simulated annealing

The design of a rendezvous phasing special-point maneuvers can be formulated as a mixed one-zero, integer and continuous design variables problem. A hybrid approach combining simulated annealing (SA) with Newton's method is proposed for solving this problem. An integer-coded SA is used to handle the discrete design variables, while Newton's method is applied to handle the continuous design variables. Three improvements are employed to make the proposed approach more efficient and robust. A two-day low-earth rendezvous-phasing problem is used as an example. The effects of the improvements are investigated. The results show that the SA based hybrid approach is very effective and efficient and the SA has better convergence ability compared with an integer-coded genetic algorithm.     

Small Ku-band phased array antenna system

A four-element phased array antenna prototype with varactor tuning has been constructed. The design employs aperture-fed quarter-wave patch elements and loaded-line phase shifters, having a phase adjustment range of about 50/spl deg/, which enables beam steering up to 13/spl deg/ from the array boresight. The system is suitable as a building block for larger arrays and shows as such a maximum gain of 7.7 dBi and an impedance bandwidth of 1 GHz. The sidelobe level is better than -13 dB. Problems encountered include parasitic resonances which disturb matching, and partially deteriorate the radiation pattern. Additionally, mechanical manufacturing tolerances of the microstrip boards were not always adequate, whereby a 6% shift in the center frequency, some impedance errors, and phasing inaccuracies were observed.     

Optimal Terminal Rendezvous as a Stochastic Differential Game Problem

The optimal terminal rendezvous of two satellites in orbit about the Earth is studied using a stochastic model and formulating the rendezvous as a game problem. Each satellite has noise-corrupted output measurements and uses a Kalman filter to generate the best estimate of the states describing the rendezvous. The optimal control for the satellites is determined. A comparison is made in terms of dimensionality and complexity to a deterministic solution of the rendezvous problem.     

路径约束的时间最短多脉冲交会全局优化

不同于现有的多脉冲最优交会研究多集中于交会时间固定的最省燃料优化,研究了路径约束和脉冲受限的多脉冲最短时间交会问题。综合考虑了交会测量视场角、脉冲总量和脉冲作用时刻等约束,基于Lam-bert交会算法,建立了多脉冲交会最短时间优化的非线性规划模型。为了高效获得全局最优解,采用了模拟退火算法用于非线性优化问题的求解。最后,通过解决一个寻的三脉冲交会问题验证了模型和算法的有效性。该研究方法可寻找满足特定约束条件的最优交会轨道。     

`And we were tired': fatigue and aircrew errors

It is argued, on the basis information obtained by the NASA Aviation Safety Reporting System (ASRS), that the majority of errors made by aircrew members are cognitive errors, not control errors, and that a major contributing factor is fatigue. The ASRS incident reports indicate some aircrews often receive less than six hours of sleep, experience desynchronosis, and lack proper nutrition. The ways in which all these factors affect both individual performance and group (crew) performance are discussed