Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

基于稀疏重建的MIMO-OTH雷达多模杂波抑制算法

针对由多模传播引起的多普勒扩展杂波(SDC)严重影响天波超视距雷达(OTHR)对慢速船舰目标的检测这一问题,在基于多输入多输出体制的新一代天波超视距(MIMO-OTH)雷达系统下,利用空域信息抑制多模SDC。传统处理方法需要目标角度先验信息,而在实际中,该信息往往很难获得。为此,提出一种新的基于稀疏重建的多模杂波抑制算法。该算法将二维的稀疏角度搜索转变为一维的角度搜索,使运算量大大降低,且估计出的收发角(DOA-DOD)自动配对,同时可获得各个传播路径下信号的时间多普勒信息,达到了理想的MIMO-OTH雷达多模杂波抑制效果。仿真结果证明了所提算法的有效性。     

An effect of range-heterogeneous clutter on adaptive Dopplerfilters

The practical implementation of adaptive Doppler filters requires estimates of clutter parameters to determine the adaptive weights. A method of deriving the estimate via the sample matrix inversion (SMI) algorithm using multiple data snapshots from adjacent range cells is presented. For homogeneous clutter environments, the results of this technique asymptotically approach the optimum (a priori known covariance matrix) as the number of snapshots approaches infinity; this asymptotic behavior does not occur for heterogeneous clutter environments. An equation for the decrease in improvement factor is derived. To promote understanding, the simplified special case of narrowband clutter is considered in detail. In almost all cases, the loss is small     

基于杂波子空间估计的MIMO雷达降维STAP研究

 多输入多输出(MIMO)雷达是近年来出现的一种新体制雷达,针对MIMO体制的机载雷达开展空时自适应处理（STAP）技术研究是值得进一步努力的方向。本文研究了机载MIMO雷达STAP技术的降维算法,通过对STAP技术杂波抑制原理进行分析,推导并得到一种基于杂波子空间的降维算法。结合扁长椭球波函数（PSWF）的特点,提出了一种基于杂波子空间估计的降维算法,并与若干降维算法的杂波抑制性能进行比较。结果表明,当存在阵元幅相误差时,该算法在保持杂波抑制性能的同时能够有效地降低STAP算法的运算量。     

High Power Radar Implementation of Coherent Waveforms

The radar use of coherent burst waveforms to obtain clutter suppression is summarized and problems arising from the high power implementation of such waveforms are discussed. These problems arise from the nonlinear nature of the typical high power radar transmitter and result in loss of subpulse-to-subpulse amplitude and phase accuracies, causing clutter suppression degradation. adaptive control loop used to measure transmission errors and provide continuous updating to minimize such errors is proposed. Residual transmission errors resulting via use of the control loop are calculated and shown to have an insignificant effect upon the clutter suppression properties of the coherent waveform. Experimental verification of control loop performance is presented.     

Robust range alignment algorithm via Hough transform in an ISARimaging system

The inverse synthetic aperture radar (ISAR) algorithm for imaging objects moving in a straight line requires range alignment as a preprocessing step since scatterers migrate through the various range bins. The conventional correlation alignment method fails when applied in ground scenarios like an airport due to the clutter environment. A procedure using Hough Transform (HT) alignment is presented which overcomes this disadvantage and provides information for clutter elimination     

Nonuniform Three-dimensional Configuration Distributed SAR Signal Reconstruction Clutter Suppression

This paper deals with the problem of clutter suppression in spaceborne distributed synthetic aperture radar (D-SAR) with nonuniform three-dimensional (3D) configuration geometry. In order to make a breakthrough of the configuration limitation of the traditional space time adaptive processing (STAP) based on uniform array and improve the inhomogeneous clutter suppression performance, this paper considers signal reconstruction technique using array interpolation to process the D-SAR signal. An array interpolation signal reconstruction method based on pitching-partition is derived then a signal reconstruction 3D-STAP clutter suppression method applied to nonuniform 3D configuration is proposed. In particular, the proposed method is compared with conventional methods and the performance analysis is carried out based on simulations. The improvement factor (IF) for clutter suppression is imported and reported as a benchmark on the clutter suppression effect.     

基于约束序贯M估计的时空域融合红外杂波抑制

针对红外弱小目标检测中的强背景杂波干扰抑制问题进行研究,提出了一种基于参数约束序贯M估计的时空域融合自适应杂波抑制算法.该算法首先在分析序列图像帧间失配的基础上建立了一种改进的时空域融合背景预测模型,结合二维离散傅里叶快速变换图像配准和双线性插值方法进行灰度值估计;然后,基于约束序贯M估计方法进行模型参数的自适应估计,...     

Design of Optimal Radar Signals Subject to a Fixed Amplitude Constraint

The problem of designing finite-pulse-train radar signals and receivers to maximize the detectability of targets masked by thermal noise and clutter returns is considered in this paper. A practical constraint is introduced: the amplitude of each subpulse in the transmit waveform is taken to be fixed. The need for such a constraint is dictated in most radar applications, because the transmitter is most efficiently utilized by saturating its amplifying tube. An algorithm for generating optimal waveforms subject to this new constraint is presented, and the performance of the resulting waveforms is compared with those obtained using existing optimization techniques.     

Track-While-Scan Algorithm in a Clutter Environment

A track-while scan (TWS) algorithm is developed for targets in a clutter environment. The problem has been studied using only the position measurements [1, 5-8], but the simulation results have not been satisfactory. Modern processing techniques (FFT processor) ) in air traffic control and surveillance radar receivers provide both position and radial velocity. The radial velocity measurement may be conveniently used in the target-track correlation process, which will reduce the association ambiguity in the clutter environment. t. In the clear environment the algorithm using the position and radial velocity measurements has been treated in [3, 4]. A TWS algorithm, using both position and radial velocity measurements for targets in a clutter environment, is presented here. The algorithm obtained is nonlinear and adaptive. In order to evaluate the improvement due to radial velocity measurement a simulation has been performed on a digital computer. The algorithm was run with and without radial velocity measurements to compare its performances. An improvement was noted especially when the target path included an accelerated portion.     

Efficient robust AMF using the FRACTA algorithm

The FRACTA algorithm has been shown to be an effective space-time adaptive processing (STAP) methodology for the airborne radar configuration in which there exists nonhomogeneous clutter, jamming, and dense target clusters. Further developments of the FRACTA algorithm are presented here in which the focus is on the robust, efficient implementation of the FRACTA algorithm. Enhancements to the FRACTA algorithm include a censoring stopping mechanism, an alternative data blocking approach for adaptive power residue (APR) censoring, and a fast reiterative censoring (RC) procedure. Furthermore, a coherent processing interval (CPI) segmentation scheme for computing the adaptive weights is presented as an alternative approach to computing the adaptive matched filter (AMF) weight vector that allows for lower sample support and reduced computational complexity. The enhanced FRACTA algorithm, denoted as FRACTA.E, is applied to the KASSPER I challenge datacube which possesses dense ground target clusters that are known to have a significant deleterious effect on standard adaptive matched filtering (AMF) processors. It is shown that the FRACTA.E algorithm outperforms and is considerably more computationally efficient than both the original FRACTA algorithm and the standard sliding window processing (SWP) approach. Furthermore, using the KASSPER I datacube, the FRACTA.E algorithm is shown to have the same detection performance as the clairvoyant algorithm where the exact range-dependent clutter covariance matrices are known.     

Maximizing the Usable Bandwidth of MTI Signal Processors

A technique is presented for maximizing the percentage of usable Doppler bandwidth throughout which a radar return can be detected while maintaining an acceptable clutter suppression. The technique employs the weighted Chebyshev approximation to the design of a transversal high-pass digital filter which has an optimal passband ripple for a given number of filter weights and associated integration gain consistent with the required increase in signal-to-noise ratio needed for acceptable probabilities of detection and false alarm. Conventional approaches to the design of a movingtarget arget indictor (MTI) filter which maximizes the improvement factor by clutter suppression typically improve the signal-to-background noise ratio over less than 50 percent of the range between dc and the pulse-repetition frequency fT. This technique can increase the usable bandwidth to 80 percent or more of fT. Two examples are included which utilize parameter values from the Army Missile Command's experimental radar and demonstrate the interactive influence of such filter parameters as the number of weights, passband ripple and bandedge, and stopband attenuation and cutoff.     

自适应强杂波抑制与点状动目标检测

研究了基于自适应图像杂波抑制的微弱点状动目标检测技术。首先利用四叉树算法,将原始的非平稳图像分割成多个准平稳的图像子块,然后对各子块进行LS自适应背景杂波估计与抑制,从而获得准高斯白噪声背景;再利用目标运动连续性假设,将目标在相邻多帧上的位置状态模型化为高阶马尔可夫数据链,建立轨迹状态空间;根据该模型采用多帧沿轨迹非线性集成算法进行检测。既克服了传统的三维匹配算法造成搜索次数巨大的弱点,同时也避免了二维投影检测带来的信噪比下降。理论分析和大量仿真实验证明了其有效性。     

Multiple scan joint probabilistic data association

This paper presents a multiple scan or n-scan-back joint probabilistic data association (JPDA) algorithm which addresses the problem of measurement-to-track data association in a multiple target and clutter environment. The standard single scan JPDA algorithm updates a track with weighted sum of the measurements which could have reasonably originated from the target in track. The only information the standard JPDA algorithm uses is the measurements on the present scan and the state vectors and covariance matrices of the present targets. The n-scan-back algorithm presented here uses multiple scans of measurements along with the present target information to produce better weights for data association. The standard JPDA algorithm can utilize a formidable amount of processing power and the n-scan-back version only worsens the problem. Therefore, along with the algorithm presentation, implementations which make this algorithm practical are discussed and referenced. An example is also shown for a few n-scan-back window lengths     

风电场雷达杂波动态重构抑制方法

随着风电场的大范围建设，风轮机杂波对雷达的干扰问题日益严重，常规杂波抑制方法难以有效解决风轮机杂波（WTC）干扰问题，因此提出了一种利用动态字典对风轮机杂波进行稀疏重构进而抑制的方法。首先，建立了WTC干扰下的雷达信号模型并分析了风轮机杂波的信号特征。其次，依据WTC的时频特征提出了一种微动参数粗估计方法，利用粗估计结果缩小了字典稀疏重构参数范围，在此基础上利用正交匹配追踪（OMP）算法对字典进行动态生成，并逐级更新字典原子。最后，通过动态字典对风轮机杂波信号进行稀疏重构，从而实现了对WTC的有效抑制。通过仿真实验，分析了风轮机杂波对目标检测的干扰影响，验证了基于动态稀疏重构的风电场杂波抑制方法在不同情况下的有效性。     

Diffusion analysis of track loss in clutter

In tracking a target through clutter, the selection of incorrect measurements for track updating causes track divergence and eventual loss of track. The plot-to-track association algorithm is modeled as a Markov process and the tracking error is modeled as a diffusion process in order to study the mechanism of track loss analytically, without recourse to Monte Carlo simulations, for nearest-neighbor association in two space dimensions. The time evolution of the error distribution is examined, and the connection of the approach with diffusion theory is discussed. Explicit results showing the dependence of various performance parameters, such as mean time to lose track and track half-life, on the clutter spatial density are presented. The results indicate the existence of a critical density region in which the tracking performance degrades rapidly with increasing clutter density. An optimal gain adaptation procedure that significantly improves the tracking performance in the critical region is proposed     

Clutter Suppression Properties of Weighted Pulse Trains

A common but troublesome requirement on radar sensors is the detection of a target in the interference from undesired scatterers, or clutter. Systems with coherent processing of pulse trains are uniquely suited for the purpose because, with pulse trains, it is possible to concentrate the receiver output for particular values of Doppler and thus suppress the clutter by Doppler filtering. This paper discusses to what degree the effectiveness of the method can be enhanced by tapering, or weighting, of the pulse amplitudes. The general results are illustrated by computer-plotted response functions for weighted pulse trains. The clutter suppression efficiency of weighting is calculated both for unilateral weighting in the receiver and for bilateral weighting in both receiver and transmitter. The significance of additional phase weighting is discussed and the results for pure amplitude weighting are compared with publishedwork on phase and amplitude weighting.     

空域数据重排的后多普勒自适应处理方法

传统的后多普勒自适应处理方法,如因子法(FA)和扩展因子法(EFA)虽然能大大降低自适应处理时的运算量和独立同分布样本的需求量,但由于实际中均匀训练样本数目的限制,当天线阵元数进一步增大时,FA和EFA抑制杂波和检测动目标的能力会显著恶化。针对这一问题,提出了一种空域数据重排的后多普勒自适应处理方法。该方法将多普勒滤波后的空域数据重排为一行列数相近的矩阵,空域滤波器权系数也表示成可分离的形式,从而得到一双二次代价函数,利用循环迭代的思想求解权系数。实验表明该方法具有快速收敛,所需训练样本少的优点,尤其在大阵列、小样本条件下该方法抑制杂波的性能明显优于FA和EFA。     

Doppler ambiguity resolution using multiple PRF

An algorithm for velocity ambiguity resolution in coherent pulsed Doppler radar using multiple pulse repetition frequencies (PRF) is presented. It relies on the choice of particular values for the PRFs. The folded frequency of the target signal is obtained by averaging the folded frequency estimates for each PRF, and a quasi maximum likelihood criterion is maximized for ambiguity order estimation. The fast implementation of this nonambiguous estimation procedure is based on the fast Fourier transform (FFT), The proposed waveform allows full exploitation of any (even) number of PRFs, which appears to be important for estimation improvement. The effects of the waveform parameters and the folded frequency estimation variance on the performance of the ambiguity order estimation procedure are evaluated theoretically and through computer simulations. Mean square error (MSE) curves are given to assess the Doppler frequency estimation accuracy. Finally, the new method is compared with a classical technique and the implementation of the algorithm in a clutter environment is addressed.     

Algorithms for Spatial Laser Beacon Acquisition

The pointing system for optical data transmission over unguided channels uses a return beacon from the receiver back to the transmitter to aid the reciprocal alignment of the two stations. We concentrate on CW or pulsed-beacon acquisition with array detectors in the presence of extended clutter in addition to background and receiver noises. Acquisition in the presence of a single interferer (jammer) is also considered. A maximum likelihood (ML) approach is used when preliminary scene information is available. In the case of unknown scenario, a picture-picture subtraction algorithm is considered for the pulsed laser. Performance is evaluated in terms of probability of an acquisition error for Poisson statistics of the photodetector output.