Energy Detection of a Random Process in Colored Gaussian Noise

A likelihood receiver for a Gaussian random signal process in colored Gaussian noise is realized with a quadratic form of a finite-duration sample of the input process. Such a receiver may be called a "filtered energy detector." The output statistic is compared with a threshold and if the threshold is exceeded, a signal is said to be present. False alarm and detection probabilities may be estimated if tabulated distributions can be fitted to the actual distributions of the test statistic which are unknown. Gamma distributions were fitted to the conditional probability densities of the output statistic by equating means and variances, formulas for which are derived assuming a large observation interval. A numerical example is given for the case in which the noise and signal processes have spectral densities of the same shape or are flat. The optimum filter turns out to be a band-limited noise whitener. The factors governing false alarm and detection probabilities are the filter bandwidth, the sample duration, and the signal level compared to the noise. Two sets of receiver operating characteristic curves are presented to complete the example.     

A Method for Setting a Test Signal Level Relative to Noise

A method is described for adjusting the leval of an RF test signal generator relative to the noise level at the receiver output. The method compares a detected output to a threshold and counts the number of times noise and signal plus noise cross the threshold in a given number of tries. By setting the threshold at a given false alarm probability for noise alone and then adding the test signal and adjusting its level to give a specified detection probability, the signal-to-noise ratio can be calibrated to an accuracy that depends on the number of samples used to measure the probabilities. The false alarm and detection probabilities are given for best accuracy as well as the rms error in signal-to-noise ratio as a function of the number of samples used.     

Fluctuating Target Detection in Clutter Using Sidelobe Blanking Logic

In an earlier paper, Maisel [6] considered two-channel detection systems using a sidelobe blanking logic when a nonfluctuating target was present. This paper is an extension of the earlier work to include fluctuating targets. The Swerling I, II, III, and IV models are considered when single-pulse detection is of interest. An adaptive threshold procedure is also briefly discussed whereby the probability of false alarm at any given resolution cell is maintained constant, even though the input clutter level may vary from cell to cell or from beam position to beam position. Useful data are presented for detection probabilities in the range 0.5 to 0.9, for false alarm probabilities in the range 104 to 10-8, and for a false detection probability of 0.1 for a sidelobe target yielding an apparent signal to total noise power density ratio of 13.0 dB in the main beam receiver.     

False Alarm Rate and False Alarm Number for Discrete and Continuous Time Sampling

A comparison of the false alarm rates and false alarm numbers for discrete and continuous time sampling is given for different noise spectrums (rectangular, Hamming, Gaussian, and cosine noise voltage spectrums) and for different sampling rates for the case of discrete time sampling. Also given is the increase in the false alarm rate when going from discrete to continuous time sampling when the detection threshold is held fixed. The amount that the threshold has to be increased for continuous sampling to achieve the same false alarm rate obtained with discrete time sampling is also given.     

Multiple-Tone Signals and Detection Probabillities

An analysis technique is presented for multiple-tone signals insystems employing noncoherent integration of a square-law detectoroutput. It is shown how the characteristic function for the teststatistic can be found from the easily determined "coherent"characteristic function defined in the two-dimensional signal space.This result is applied to two detection problems, the detection of multiple-tone signals in Gaussian noise and the detection of a Gaussian signal in multiple-tone plus Gaussian noise interference.The detection curves are compared to an approximation that is often used in practice to estimate performance. It is found that detection performance in the presence of multiple-tone interferences can be significantly different from that in the presence of Gaussian noise alone.     

Second time around radar return suppression using PRI modulation

A technique for suppressing second-time-around radar returns using pulse-repetition interval (PRI) modulation is presented and analyzed. It is shown that a staggered PRI radar system can offer considerable improvement over a nonstaggered radar system in rejecting second-time-around returns which cause false alarms. This improvement is a function of detector implementation (noncoherent integrator or binary integrator), the number of staggered PRIs, the quiescent false alarm number, the Swerling number of the false return, the transmitted signal power, the second-time-around noise power, and the quiescent noise power of the radar. Small changes in transmitted signal power can be traded off with the quiescent false alarm number to suppress the bogus return significantly. In addition, for a noncoherent integrator, all other parameters being equal, if the second-time-around return is a Swerling case II or IV target, then there is an optimum number of staggered PRIs that can be chosen to minimize the likelihood of its detection. It is also shown that the binary integrator significantly reduces the number of second-time-around return detections when compared with the noncoherent integrator. However, there is an accompanying loss of detection     

Coherent detection in Laplace noise

The discrete-time detection of a time-varying, additive signal in independent Laplace noise is considered. Previous efforts in this area have been restricted to the constant signal, and identically distributed noise case. Theoretical (closed form) expressions for the false alarm and detection probabilities are developed for both the Neyman-Pearson optimal detector and the classical matched filter detector. Comparisons between the two detectors are made which illustrate the effects of signal-to-noise power ratio and sample size for certain false alarm and detection probability constraints. In view of the fact that the optimal Laplace detector is not UMP, we also investigate the effect of signal amplitude mismatch     

An algorithm for detection of moving optical targets

An algorithm is described for detecting moving optical targets against spatially nonstationary Poisson background and noise. The algorithm has applications in optical detection of objects such as meteors, asteroids, and satellites against a stellar background. A maximum-likelihood approach is used which results in reducing interference from stars. It is shown that by choosing a detection threshold to provide a constant false alarm rate, the resulting algorithm is independent of the signal strength of the target. An analysis of this algorithm is presented, showing the probability of detection for several false-alarm rates     

基于先验门限优化准则的探测阈值自适应选择

针对 2维测量和 4 -sigma确认门 ,把先验检测门限优化准则和修正 Riccati方程的解析近似表示相结合 ,得到了在瑞利起伏环境下使跟踪性能优化的信号探测阈值解析表示式 ,从而使在线求解自适应信号探测阈值能比较容易地实现。通过研究和仿真发现 :在滤波稳定阶段 ,本文给出的自适应信号检测门限方法的跟踪性能优于固定虚警率方法的跟踪性能 ;基于先验检测门限优化准则实现检测 -跟踪的联合优化要求信噪比要大于一定的门限 ,在瑞利起伏环境下 ,对 2维测量和 4 -sigma确认门 ,该门限为 1 .57     

Envelope Threshold Detection in a Class of Non-Gaussian Interference

This paper considers the detection of a sinusoidal or chirp signal imbedded in wideband FM interference (as might be generated by some types of active jamming), such that after pulse compression or other integration, the interference can be approximated by a sum of sinusoids of independent phase. The detection probability in such non-Gaussian noise is compared to that for Gaussian noise, with the Gaussian result approached, as required, in the limit that the number of sinusoids in the sum increases without bound. For detection using a comparison of the envelope with a threshold which yields a given false-alarm probability (CFAR detection), the detection probability is improved over the case of Gaussian noise, so that the usual approach basing the design on Gaussian noise would be conservative. Using a threshold determined from the envelope mean, the FM interference yields a lower false-alarm probability than for Gaussian noise, with detection probability only slightly degraded.     

Detection Performance of Soft-Limited Phase-Coded Signals

General analytic expressions are developed for the soft-limited digital pulse compressor (matched filter). This theoretical development is then used for the hardware realization of a two-channel (I,Q), 3-bit-limited digital pulse compressor with a compression ratio of 255: 1. The realized hardware uses state of the art integrated circuit devices. An experimental laboratory setup is described. This setup is used to study hard-limited versus 3-bit-limited matched-filter performance characteristics with the data in the following areas: 1) constant false alarm rate (CFAR) characteristics as a function of threshold settings and noise levels; 2) single target detection characteristics as a function of input signal-to-noise ratio (SNR); and 3) two target performance characteristics: a) the amplitude of a weaker target as a function of target ratio and target overlap; and b) the detection characteristics of a weaker target as a function of weaker target SNR, strong target SNR, and target overlap.     

Detectability of Spread-Spectrum Signals

Methods of detecting spread-sprectrum signals without knowledge of the pseudorandom code used to generate the signal are described. Exact and approximate methods of calculating relationships among detection probability, false alarm rate, and signal-to-noise ratio are given for radiometers and for channelized pulse-detection systems. The detection performance of the radiometer is compared graphically with that of pulse-detection systems, for two different kinds of pulse detection decision rules. Detection performance as a function of certain signal parameters is shown to be very different for a pulse-detection system than for a radiometer, and this difference in behavior provides a basis for selecting signal parameters that minimize the probability of detection. The reasoning that underlies the selection process is explained, and the process is outlined for each of several signal parameters.     

Detection Performance of a Mean-Level Threshold

The problem of detecting signals in nonstationary clutter is met by presenting a mean-level or adaptive threshold which adjusts to the changing background level. Such a threshold performs better than a fixed threshold that must be set for the highest amplitude clutter. However, the mean-level threshold does not perform as well for stationary noise as a fixed threshold set at the proper value. One measure of effectiveness of an adaptive threshold is its performance in stationary noise (compared to the optimum fixed threshold) for a specified speed of response. For the mean-level threshold, a simple mathematical solution is found for the detection probability when the noise is stationary and the signal scintillates rapidly. The performance is evaluated for a wide range of mean-level-threshold time constants and for several false-alarm probabilities. The results are presented graphically. As an example, the mean-level threshold suffers 3 dB in detectability (equivalent signal-to-noise ratio) in the presence of stationary noise as compared to the optimum fixed threshold for 50-percent probability of detection, false-alarm probability of 10-8, and an adjustment time of 15 times the signal duration.     

Multistatic-Radar Binomial Detection

The performance of multistatic-radar binomial detectors is investigated. Although conceptually similar to the well-knwn "M-out-of-N" detector frequently considered for monostatic systems, the multistatic detector must cope with false alarms generated by target et ghosting as well as by noise threshold crossings. A procedure for deriving the detection statistics of multistatic binomial detectors ors is presented. The procedure is applied to derive the detection probabilities for a spectrum of false alarm probabilities, target densities, and numbers of radar receivers.     

An Adaptive Threshold System for Nonstationary Noise Backgrounds

The problem of detecting target signals in an ocean environment using active sonar is complicated by the nonstationary background which usually consists of both ambient ocean noise and reverberation. on. In this paper a signal processing system capable of detecting a signal in nonstationary noise is introduced. This system makes use of the mean and variance time functions of the nonstationary noise background in order to design estimation filters which will cope with the nonstationarity. Appropriate statistics of the noise and signal (tone burst) plus noise have been obtained and are used to determine the probabilities of false alarm and detection and the receiver operating characteristics.     

基于切片熵权的WHT多LFM信号识别方法

为提高在低信噪比与先验信息不足条件下对线性调频(LFM)信号识别能力,借鉴信息论中的熵权法改进WHT(Wigner-Hough Transform),提出了一种基于切片熵权的WHTE(Wigner-Hough Transform based on Entropy)算法。推导出LFM信号的WHT与对应特性,将WHT变换域内极半径和角度切片的熵值来转换为权重因子,进而对每个切片进行加权处理,采用双层权重以弱化噪声与干扰项的影响,并推导出LFM信号与高斯白噪声在WHT维度内不同假设条件下的概率密度分布函数,构建了对于LFM信号WHT后恒虚警检测的完备流程。通过理论分析与公式推导论证了算法的可行性,并与WHT、分数阶傅里叶变换与周期WHT算法的仿真对比,验证了算法的有效性,凸显WHTE算法能够在强噪声背景下与没有先验支撑时实现对LFM信号的良好检测。     

非合作无源探测中的假设检验弱目标检测方法

在非合作无源探测系统中,弱目标回波不仅会受到强直达波、强多径的干扰,还会受到强目标的掩盖干扰,因此很难对其进行有效检测。为了解决这一问题,提出了一种基于多择复合假设检验的弱目标检测方法。首先将接收信号投影到多径干扰的正交补子空间内,以消除强直达波和强多径干扰,然后将目标检测看作一个多择复合假设检验问题,建立了与之相应的基本框架模型,利用最大后验估计方法对目标时延、多普勒频移及信号幅度等参数进行估计,构造检验统计量,设置相应的门限,根据假设检验结果,逐个消除强目标干扰从而达到检测弱目标的目的。仿真结果表明,本方法可以有效抑制强直达波、强多径及强目标干扰,有效检测出弱目标,且虚警率低。     

基于样本熵的语音信号检测算法

船舶自身发出的巨大噪声,严重影响了通讯设备通讯端船舶工作者的正常语音交流和通讯,须要进行语音信号增强,将语音信号从背景噪声中检测分离出来。为此,文章在分析语音信号与船舶背景噪声信号时域序列复杂性基础上,提出基于信号序列样本熵的语音信号检测算法。该算法将含噪信号进行分帧后,首先计算每帧信号的样本熵,并根据自适应预设阈值对信号进行初始判断；然后,利用信号通常持续一定时间的连续性,对信号初始判断进行平滑,得到信号的最终判别类别,实现对语音信号的检测。经过大量实测实验数据的验证,环境噪声信号的辨别准确度为 90.33%,语音信号为 95.05%,该算法取得了较好的判别精度。     

On the performance of serial networks in distributed detection

Distributed detection on the serial (or tandem) topology is considered with the probability of error performance criterion. Previously published efforts, while presenting probability of detection versus false alarm results, limited the number of array elements to two or three. For the detection of known, equally likely signals in additive, symmetric noise, the author presents simple recursive expressions for the threshold values and the performance of the system. Examples for known signals in Gaussian and Laplacian noise show the degradation in performance due to the array structure