SMA智能复合材料结构的有限元分析与实验研究

建立了嵌入形状记忆合金(SMA)丝作为智能驱动器的智能复合材料层板结构模型,并对结构变形进行了分析。对SMA的本构关系进行了推导,得到了不同温度下的应力应变关系,并加入了界面的柔化折算,采用数值方法求解。驱动器镶嵌于层板表面或内部,根据电阻反推得到准确的温度。不同温度下的驱动变形计算结果同试验结果吻合较好。对结构的振动特性进行了测试,得到了不同温度下的模态频率变化。     

形状记忆合金驱动器动态驱动性能研究

对Ni Ti形状记忆合金(Shape Memory Alloy,SMA)在准静态和动态加热工况下回复应力的变化规律进行了研究,提出了准静态工况下的本构模型迭代算法,该算法可以较好地吻合试验数据。同时阐述了SMA丝作为驱动器时,传统本构模型在动态加热工况下的局限性,并提出了一种简洁高效的平均速率插值算法。该算法能较好计算动态加热工况下SMA丝驱动回复应力,与试验结果相比较,相对误差小于10%。     

一种低速连续旋转SMA电机的设计与试验

利用形状记忆合金(SMA)的记忆特性设计了一种低转速,可连续旋转的电机;利用Liang-Rog-er本构模型进行了SMA-弹簧的旋转位移驱动器的设计以及电机扭矩和转速的设计;完成了SMA电机的机械结构设计;完成了控制规律设计;进行了性能试验.研究结果表明,在试验温度27℃下,用6 V恒压电源驱动的SMA电机实现了连续旋转,转速为0.03 rad/min.SMA电机转速低,扭矩大,功率密度高,可连续旋转,有很大的工程应用潜力.      

基于双程形状记忆合金驱动器的可偏转翼梢小翼控制

<正>1962年,美国海军武器实验室的Buehler等发现等原子比的NiTi合金具有优良的形状记忆效应~[1],并成功研制出廉价且力学性能优异的形状记忆合金"NiTinol"~[2]。形状记忆合金材料因其具有形状记忆效应而可用于制作驱动器,SMA驱动器具有结构简单、驱动力大、功率重量比高、响应迅速等优点,在实际中特别是在飞行器机翼变体结构中得到了大量的应用~[3],然而单向形状记忆效应不适用于形状记忆合金丝的重复驱动~[4],因为驱动器在冷却后不会恢     

形状记忆合金(SMA)在机器人夹持器中的应用研究

形状记忆合金具有感温—驱动的特性,将其用作机器人夹持器的驱动元件,可以使夹持器具有结构简单、体积小、重量轻等优点。本文主要研究了SMA驱动元件的控制方式及记忆外形的选取与性能测试,设计了多种SMA弹簧夹持器,通过安装于SCARA机器人上进行垛盘轴孔的装配实验,证明SMA夹持器能很好地完成装配任务。     

一种行波型超声电机驱动器的研制

针对超声电机的工作原理和驱动要求,研制一套适用于行波型超声波电机的驱动器。对比分析驱动器与普通驱动电源对超声电机性能的影响,实验结果表明,驱动器的输出波形与参数均满足设计要求,超声电机的输出性能也基本一致。在超声电机长时间运行过程中,电机与驱动器的输出性能均稳定。     

介电型电活性聚合物(EAP)驱动器失效行为分析

 介电型电活性聚合物(EAP)驱动器在工作过程中,边界条件及驱动电压的改变经常导致EAP薄膜发生起皱现象以及介电击穿,致使驱动器失去工作能力.为了保障驱动器的正常工作,避免失效行为的发生,对EAP驱动器的失效行为进行了研究.针对锥形驱动器,计算出不同驱动电压下驱动器EAP薄膜的变形情况以及其中的应力、应变和电场强度的分布情况.利用薄膜起皱判别方法,对驱动器的起皱行为进行预测,同时分析了预拉伸倍数对驱动器失效的影响.试验结果表明,EAP驱动器的理论临界起皱电压与理论分析比较吻合,预拉伸可以提高薄膜的机电稳定性能.研究结果可用于预测介电型EAP驱动器发生失效的临界电压,有利于保障驱动器的安全工作.     

形状记忆合金智能结构的主动振动抑制研究

 从形状记忆合金 (SMA)智能结构用于主动振动抑制的构想出发,建立了含SMA非线性本构关系的智能复合材料结构的有限元模型,并结合试验验证了主动振动抑制的效果。试验和计算结果都表明SMA是振动抑制的有效驱动器,通过主动应变能调整 (ASET)的方法对结构固有频率的影响非常显著,这种影响主要体现在基频 (一阶固有频率 )的改变上,对高阶固有频率的影响逐渐减小。     

直升机后缘襟翼驱动器迟滞现象仿真与抑制

直升机后缘襟翼多采用压电驱动器作为驱动元件，但是在使用过程中压电驱动器迟滞会对其振动控制性能产生不利影响，因此针对压电驱动器迟滞开展了迟滞建模与抑制研究。通过实验研究了压电驱动器在不同驱动频率下的迟滞特性，采用Bouc-Wen模型对驱动器迟滞现象进行了建模，并采用粒子群算法（PSO）辨识模型参数，与实际测量迟滞曲线进行了对比，在10~60 Hz范围内所建立的迟滞模型能够较为精确地描述压电驱动器迟滞现象。建立了基于Bouc-Wen逆模型的前馈补偿控制与PID反馈控制相结合的复合控制策略，实验结果显示该控制策略能够在10~60 Hz较宽的频率范围内有效抑制该压电驱动器迟滞现象。建立了考虑驱动器迟滞的主动控制后缘襟翼振动控制动力学模型，并对中等速度稳态前飞条件下后缘襟翼振动控制性能进行了仿真，仿真结果显示驱动器迟滞会在一定程度上削弱振动控制性能，而采用复合控制可以提高后缘襟翼旋翼振动控制性能。     

基于PSZT的RAINBOW型驱动器研究

基于反铁电陶瓷 (PSZT)化学还原制备的 RAINBOW驱动器是一种具有内部应力偏移 ,兼有还原层和氧化层 ,驱动位移较大的新型驱动器。实验发现 :反铁电陶瓷较易还原 ,理想还原条件为 :870℃保温 2～ 3h;与普通反铁电驱动器相比 ,RAINBOW驱动器能在强度较低的电场作用下发生铁电相变 ,并得到很大的轴向位移 (约 190μm) ;加载方式对 RAINBOW的驱动性能具有决定性的影响     

Nonlinear hysteresis identification and compensation based on the discrete Preisach model of an aircraft morphing wing device manipulated by an SMA actuator

The conception of aircraft morphing wings thrives in aeronautics since the appearance of shape memory alloys(SMAs). An aircraft morphing wing device, manipulated by an SMA actuator, inherits the intrinsic nonlinear hysteresis from the SMA actuator, ending up with control disadvantages. Conventionally, systems with SMA actuators are constrained to bi-stable states to bypass the hysteresis region. Rather than retreating a morphing wing device to bi-stable states, this paper is dedicated to transcend the morphing wing device beyond the customary limit. A methodology of discrete Preisach modeling, which identifies the hysteresis of the morphing wing device, is proposed herein. An array of discrete equal-distance points is applied to the Preisach plane in order to derive the Preisach density over the partitioned unit of the Preisach plane. Discrete Preisach modeling is fulfilled by the discrete first-order reversible curve(DFORC). By utilizing the discrete Preisach model, the aircraft morphing wing device is simulated; the validity and accuracy of discrete Preisach modeling are demonstrated by contrasting the simulated outcome with experimental data of the major hysteretic loop and the wingspan-wise displacement over time; a comparison between simulation and experimental results exhibits consistency. Afterwards, a hysteresis compensation strategy put forward in this paper is implemented for quasi-linear control of the aircraft morphing wing device, which manifests a compensated shrinking hysteresis loop and attains the initiative of extending the morphing range to the intrinsic hysteretic region.     

A fuzzy PID-controlled SMA actuator for a two-DOF joint

Shape memory alloy(SMA) actuator is a potential advanced component for servosystems of aerospace vehicles and aircraft. This paper presents a joint with two degrees of freedom(DOF) and a mobility range close to ±60 when driven by SMA triple wires. The fuzzy proportional-integral-derivative(PID)-controlled actuator drive was designed using antagonistic SMA triple wires, and the resistance feedback signal made a closed loop. Experiments showed that, with the driving responding frequency increasing, the overstress became harder to be avoided at the position under the maximum friction force. Furthermore, the hysteresis gap between the heating and cooling paths of the strain-to-resistance curve expanded under this condition. A fuzzy logic control was considered as a solution, and the curves of the wires were then modeled by fitting polynomials so that the measured resistance was used directly to determine the control signal. Accurate control was demonstrated through the step response, and the experimental results showed that under the fuzzy PID-control program, the mean absolute error(MAE) of the rotation angle was about 3.147. In addition, the investigation of the external interference to the system proved the controllable maximum output.     

压电致动器扑翼结构动力学仿真

采用传统扑动机构的微型扑翼,气动效率低、扑动能耗大。采用压电致动器的微型扑翼通过压电材料进行致动使机翼产生上下扑动,有效地将扑动机构和机翼两个主要系统进行集成,不仅节省重量,同时它具有任务变形自适应能力强、气动效率高和扑动能耗小的特点。通过PCL语言建立采用压电致动器的扑翼有限元模型,结合同尺寸扑翼气动力试验数据,进行采用压电致动器扑翼结构仿真。利用仿真结果研制采用压电致动器扑翼原理样机,研究表明,采用压电致动器后扑翼扑动频率得到明显提高,压电片可有效控制机翼的弯扭变形,有助于提高扑翼的气动效率。     

机翼扭转和副翼偏转横滚操纵比较研究

机翼扭转和经典副翼后缘偏转都是未来可能的智能机翼横滚操纵方案。采用Fluent仿真软件对扭转式机翼与经典副翼构型机翼进行了对比研究,主要分析两者在升阻性能、横滚操纵力矩、压力分布等方面的差异和特征规律,得到了扭转变形机翼相对副翼舵面的横滚操纵当量作用和气动优势。所设计的机翼方案由于扭转式机翼横滚操纵的机翼变形连续性以及所需扭转角度较小,易于保持流场的附着和稳定,所以达到相同横滚力矩系数,扭转式机翼所需扭转角度为副翼偏转角度的30%～50%左右,并且升阻比显著优于副翼式机翼,而且随着操纵角度增大优势更加明显,在大舵角操纵时扭转式机翼升阻比超过副翼式机翼约一倍。     

多段柔性变体扑翼飞行器设计

多段柔性变体扑翼模仿海鸥翅膀的复杂运动.观察海鸥翅膀的运动周期,设计了包含慢频率扑动、展向折弯、弦向扭转和结构柔性变形的扑翼模型,并应用准定常方法计算气动力,为该扑翼飞行器设计提供依据.在CATIA和3DMAX中设计多段柔性变体扑翼机的三维模型和运动模拟,制作样机进行飞行试验,研究其平飞、爬升、偏航等飞行姿态,结果表明升力和推力与数值计算结果吻合.相较于原有扑翼飞行器,多段柔性变体扑翼飞行器可以慢频率扑动飞行,调整扑翼形状.      

压电纤维复合材料铺层用于翼面设计的驱动特性与刚度影响

压电纤维复合材料驱动器在形状控制、振动控制、颤振抑制与抖振控制等方面有广泛的应用前景。首先简单介绍了压电应变驱动的比拟载荷方法,并采用该方法讨论了压电陶瓷片状驱动器与压电纤维复合材料驱动器在驱动特性上的主要差异。在此基础上,对压电纤维复合材料在不同铺设方式、铺设角度与铺设层数下的驱动特性进行了分析,在刚度影响方面展示了不同铺设角度下模型刚轴的移动。分析结果表明:对称铺设反向电场可以同时获得弯曲与扭转变形,而反对称铺设同向电场主要获得扭转变形;两种铺设方式下45°铺设角均获得最大弦向转角,而0°铺设角将获得最大挠度;多铺层可以增加驱动载荷,但总体变形效果还取决于结构系统的刚度比例;对称铺设方式下铺设角对结构刚轴移动的影响非常明显,在气动弹性控制中应着重关注。     

Robust fault-tolerant control for wing flutter under actuator failure

Many control laws, such as optimal controller and classical controller, have seen their applications to suppressing the aeroelastic vibrations of the aeroelastic system. However, those control laws may not work effectively if the aeroelastic system involves actuator faults. In the current study for wing flutter of reentry vehicle, the effect of actuator faults on wing flutter system is rarely considered and few of the fault-tolerant control problems are taken into account. In this paper, we use the radial basis function neural network and the finite-time H_∞ adaptive fault-tolerant control technique to deal with the flutter problem of wings, which is affected by actuator faults, actuator saturation, parameter uncertainties and external disturbances. The theory of this article includes the modeling of wing flutter and fault-tolerant controller design. The stability of the finite-time adaptive fault-tolerant controller is theoretically proved. Simulation results indicate that the designed fault-tolerant flutter controller can effectively deal with the faults in the flutter system and can promptly suppress the wing flutter as well.     

机翼动态气动特性实验研究

介绍了动态特性风洞实验的技术方案、测试系统和测试软件。对前缘后掠６０°的三角翼在迎角０°～９０°范围内快速上仰时的升力进行了测量。结果表明：机翼快速上仰时,随上仰速率增大最大升力系数增高,即动态升力效应更明显;失速迎角也增大。此外,给出了简缩频率、平均迎角、振荡振幅以及俯仰轴位置等对振荡机翼产生的非定常瞬时力的影响     

Design and experimental testing of a control system for a morphing wing model actuated with miniature BLDC motors

The paper deals with the design and experimental validation of the actuation mechanism control system for a morphing wing model. The experimental morphable wing model manufactured in this project is a full-size scale wing tip for a real aircraft equipped with an aileron. The morphing actuation of the model is based on a mechanism with four similar in house designed and manufactured actuators, positioned inside the wing on two parallel lines. Each of the four actuators used a BrushLess Direct Current (BLDC) electric motor integrated with a mechanical part performing the conversion of the angular displacements into linear displacements. The following have been chosen as successive steps in the design of the actuator control system: (A) Mathematical and software modelling of the actuator; (B) Design of the control system architecture and tuning using Internal Model Control (IMC) methodology; (C) Numerical simulation of the controlled actuator and its testing on bench and wind tunnel. The morphing wing experimental model is tested both at the laboratory level, with no airflow, to evaluate the components integration and the whole system functioning, but also in the wind tunnel, in the presence of airflow, to evaluate its behavior and the aerodynamic gain.