共查询到8条相似文献,搜索用时 54 毫秒
1.
Solar-powered aircraft have attracted great attention owing to their potential for longendurance flight and wide application prospects.Due to the particularity of energy system, flight strategy optimization is a significant way to enhance the flight performance for solar-powered aircraft.In this study, a flight strategy optimization model for high-altitude long-endurance solar-powered aircraft was proposed.This model consists of three-dimensional kinematic model,aerodynamic model, energy collection model, energy store model and energy loss model.To solve the nonlinear optimal control problem with process constraints and terminal constraints, Gauss pseudo-spectral method was employed to discretize the state equations and constraint equations.Then a typical mission flying from given initial point to given final point within a time interval was considered.Results indicate that proper changes of the attitude angle contribute to increasing the energy gained by photovoltaic cells.Utilization of gravitational potential energy can partly take the role of battery pack.Integrating these two measures, the optimized flight strategy can improve the final state of charge compared with current constant-altitude constant-velocity strategy.The optimized strategy brings more profits on condition of lower sunlight intensity and shorter daytime. 相似文献
2.
In situ formed TiB2 particle reinforced aluminum matrix composites (TiB2/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB2 particles, the machinability is still a problem which restricts the application of TiB2/Al MMCs. In order to meet the industrial requirements, the influence of TiB2 particles on the machinability of TiB2/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB2/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB2/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB2/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material. 相似文献
3.
基于试验设计及支持向量机的向心叶轮结构优化设计方法 总被引:3,自引:0,他引:3
针对向心叶轮结构优化设计耗时长的难点,研究并采用了2类关键技术:其一是利用试验设计技术从大量的轮盘结构尺寸中挑选出重要尺寸作为优化设计变量,以减小优化问题规模;其二是利用支持向量机技术建立向心叶轮强度及振动分析的代理模型,以缩短分析时间.在以上研究工作的基础上建立了1种快速高效的向心叶轮结构优化设计方法.随后的1个算例表明:优化后的叶轮寿命提高4倍,优化设计时间为传统方法的1/27,具有良好的工程应用前景. 相似文献
4.
Minghui ZHANG Zhenli CHEN Zhaoguang TAN Wenting GU Dong LI Changsheng YUAN Binqian ZHANG 《中国航空学报》2019,32(8):1847-1859
Blended-Wing-Body(BWB) configuration, as an innovative transport concept, has become a worldwide research focus in the field of civil transports development. Relative to the conventional Tube-And-Wing(TAW) configuration, the BWB shows integrated benefits and serves as a most promising candidate for future ‘‘green aviation. The objective of the present work is to figure out the effects of the stability margin and Thrust Specific Fuel Consumption(TSFC) on the BWB design in the framework of Multi-Disciplinary Optimization(MDO). A physically-based platform was promoted to study the effect static stability margin and engine technology level. Low-order physically based models are applied to the evaluation of the weight and the aerodynamic performance. The modules and methods are illustrated in detail, and the validation of the methods shows feasibility and confidence for the conceptual design of BWB aircrafts. In order to find out the relation between planform changes and the selection of stability and engine technology level, two sets of optimizations are conducted separately. The study proves that these two factors have dominant effects towards the optimized BWB designs in both aerodynamic shapes, weight distribution, which needs to be considered during the MDO design process. A balance diagram analysis is applied to find out a reasonable static stability margin range. It can be concluded that a recommended stability margin of a practical BWB commercial aircraft can be half of that of a conventional TAW design. 相似文献
5.
Ti2AlNb intermetallic alloy is a relatively newly developed high-temperature-resistant structural material, which is expected to replace nickel-based super alloys for thermally and mechanically stressed components in aeronautic and automotive engines due to its excellent mechanical properties and high strength retention at elevated temperature. The aim of this work is to present a fast and reliable methodology of inverse identification of constitutive model parameters directly from cutting experiments. FE-machining simulations implemented with a modified Johnson-Cook (TANH) constitutive model are performed to establish the robust link between observables and constitutive parameters. A series of orthogonal cutting experiments with varied cutting parameters is carried out to allow an exact comparison to the 2D FE-simulations. A cooperative particle swarm optimization algorithm is developed and implemented into the Matlab programs to identify the enormous constitutive parameters. Results show that the simulation observables (i.e., cutting forces, chip morphologies, cutting temperature) implemented with the identified optimal material constants have high consistency with those obtained from experiments, which illustrates that the FE-machining models using the identified parameters obtained from the proposed methodology could be predicted in a close agreement to the experiments. Considering the wide range of the applied unknown parameters number, the proposed inverse methodology of identifying constitutive equations shows excellent prospect, and it can be used for other newly developed metal materials. 相似文献
6.
Effect of drag reducing riblet surface on coherent structure in turbulent boundary layer 总被引:3,自引:1,他引:3
The characteristics of turbulent boundary layer over streamwise aligned drag reducing riblet surface under zero-pressure gradient are investigated using particle image velocimetry. The formation and distribution of large-scale coherent structures and their effect on momentum partition are analyzed using two-point correlation and probability density function. Compared with smooth surface, the streamwise riblets reduce the friction velocity and Reynolds stress in the turbulent boundary layer, indicating the drag reduction effect. Strong correlation has been found between the occurrence of hairpin vortices and the momentum distribution. The number and streamwise length scale of hairpin vortices decrease over streamwise riblet surface. The correlation between number of uniform momentum zones and Reynolds number remains the same as smooth surface. 相似文献
7.
基于超椭圆方程和序列响应面法的回转壳开孔形状优化 总被引:1,自引:0,他引:1
含有多种功能开孔的轻质回转壳结构是航空航天结构系统内的常用支撑构件,其开孔形状直接影响结构的静动态性能。以回转壳结构为对象,基于超椭圆方程和坐标映射变换推导了回转壳开孔边界的参数化表达,开展了开孔形状动力学优化研究。为提高结构优化计算的精度、效率和收敛性,提出了准等弧长方法和基于均匀设计的序列响应面近似建模方法(SRSM),以分别实现空间超椭圆曲线的精确逼近、减少结构有限元分析成本和加快迭代收敛。以非支配排序遗传算法Ⅱ(NSGA-Ⅱ)作为响应面模型求解算法,结合有限元分析构建了回转壳开孔形状优化设计流程,开展了最大化结构一二阶频率带隙的典型回转壳结构开孔形状优化设计。结果表明,基于超椭圆方程和序列响应面法的开孔优化方法获得了有效改进结构动态特性的回转壳开孔形状,对开展计算耗时工程结构形状优化设计具有一定应用价值。 相似文献
8.
Jingjing ZHU Xiaojun WANG Haiguo ZHANG Yuwen LI Ruixing WANG Zhiping QIU 《中国航空学报》2019,32(9):2095-2108
Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method. 相似文献