升压式ZVT—PWM软开关变换器仿真研究

分析了零电压过渡脉宽调制型(ZVT-PWM)软开关变换器基本工作原理，利用PSPICE软件对升压式ZVT-PWM软开关变换器进行仿真，给出了仿真结果，并与一般的升压变换器进行了比较。仿真结果表明，ZVT—PWM软开关变换技术具有开关损耗小、电源电压和负载适应范围宽、恒频控制和变换效率高等优点。     

升压式ZVT-PWM软开关变换器仿真研究

分析了零电压过渡脉宽调制型(ZVT-PWM)软开关变换器基本工作原理,利用PSPICE软件对升压式ZVT-PWM软开关变换器进行仿真,给出了仿真结果,并与一般的升压变换器进行了比较.仿真结果表明,ZVT-PWM软开关变换技术具有开关损耗小、电源电压和负载适应范围宽、恒频控制和变换效率高等优点.     

一种基于开关次数最小的含零电压矢量永磁同步电机直接转矩控制开关表

介绍了永磁同步电机(PMSM)直接转矩控制(DTC)理论,研究了零电压矢量的作用。基于开关次数最小提出了选择零电压矢量的策略,给出了一种新型含零电压矢量开关表。仿真结果表明使用新型开关表PMSM DTC系统能正常驱动。与传统开关表相比,使用新型开关表DTC系统开关次数降低了近56%,进而降低了开关损耗。     

混合型逆变器的空间矢量调制策略优化

高速永磁同步电机驱动系统具有电磁时间常数小、高速区载波比低的特征,加剧了电流纹波,影响系统效率、振动噪声和电磁干扰。为降低高速永磁同步电机的电流纹波,基于SiC-MOSFET/Si-IGBT混合型逆变器设计了一种改进型低损耗空间矢量调制算法。首先,通过调整零电压矢量的生成方式和各功率器件的开关动作时序,将大部分开关动作转移至低损耗的SiC-MOSFET中,并为高损耗的Si-IGBT提供零电压开关条件,降低了逆变器损耗,提高了驱动系统的效率和可用开关频率,逆变器开关频率的提高有效降低了电机电流纹波。其次,对该算法作用时的电流纹波特性进行深入分析,在此基础上提出一种变开关频率模式的最优交轴电流纹波峰值调制算法以优化交轴电流纹波性能。然后,根据预测的交轴电流纹波峰值实时调整载波频率,通过削峰填谷的方式对交轴电流纹波进行平均,在不增加开关损耗的条件下,分散开关能量、降低转矩脉动、改善振动噪声和电磁兼容性能。所提方案的优势在于：较于传统型逆变器,逆变器开关损耗降低、效率提高,可进一步提升开关频率以改善电流纹波;较于传统空间矢量调制算法,改进了电压矢量的生成方式,并利用载波频率这一新增自由度分散能量,降低了交轴电流纹波。最后,通过仿真与实验对所提出算法的有效性进行了验证。     

大功率机电微波开关

针对大功率干扰站的大功率微波开关的技术要求，介绍了大功率微波开关的设计思路、理论分析及工程实践，着重讨论了关键技术和所采取的技术措施，并给出它的重要技术指标。     

基于压电开关分流电路技术的板的半主动振动控制

研究了状态开关与同步开关两种分流电路的振动抑制原理和实现方法；提出了一种开关控制器设计方案；并分别用于两种开关分流电路对某四边固支方板的抑振实验，结果表明所提出的开关控制器合理有效，并进一步证明，同步开关优于状态开关。实验中状态开关分流电路和同步开关分流电路控制下板的第一阶稳态响应分别得到了约13．4％和50．6％的降低；还对同步开关分流电路中，电感的有效取值范围及电感取值一定时开关的最佳持续闭合时间进行了实验验证。     

某起落架正常收／放系统失效原因分析

正确运用246雷达天线“正常或应急”液压操纵开关和液压马达壳体回油“正常或应急”开关的工作状态，关系到飞机液压操纵系统的安全性。若天线液压操纵开关和马达壳体回油开关配合不当，将引起飞机液压操纵系统失效。     

Boost变换器软开关技术的研究

提出一种新型有源软开关技术,在辅助开关和谐振电路的作用下,可以实现开关电源中开关管的零电压开通和零电压关断,而且可以减小开关管的电压应力和电流应力。对电路工作原理和参数设置进行了分析,给出了关键参数的选取原则。利用实际电路,验证了有源软开关技术的有效性。     

全碳化硅功率模块开关瞬态特性及损耗研究

为了加快全碳化硅功率模块的实际工程应用,针对全碳化硅模块开通关断过程中电压电流变化率、栅极电压耦合、开通损耗和关断损耗开展了分析,并与传统IGBT功率模块进行了对比分析。在全碳化硅功率模块双脉冲试验的基础之上,研究了不同电压电流等级下开关瞬态特性和开关损耗,提取试验参数,获得了电压电流应力大小,为全碳化硅功率模块的工程应用提供有效参考。     

高速开关阀PWM控制电路的开发

高速开关阀是电液伺服机构的惯性环节,伺服机构的品质依赖于阀的动态特性,因此阀的响应快速性很重要。提高高速开关阀的快速性,驱动电路是一个重要方面。采用2051单片机,设计了一种新型的PWM信号发生器,并开发了上下限保护电路,使其快速性得到了进一步的提高。     

并联H桥DC/DC变换器软开关技术研究

与传统的Buck电路相比,基于H桥并联的DC/DC变换器可以实现电压的双极性输出和故障时的冗余控制,非常适合用于大功率电动机正反转控制的场合。分析了并联H桥型DC/DC变换器的结构组成和双脉宽调制(PWM)模式。为了降低双脉宽调制下H桥型DC/DC变换器的开通和关断损耗,对无源软开关技术进行了分析,重点探讨了RCD缓冲电路和最小应力缓冲电路之间的性能差异,指出最小应力软开关技术可以获得更好的软开关性能,并就将其用于双脉宽调制下的并联H桥DC/DC变换器进行了仿真研究。仿真结果表明:最小应力软开关技术用于双脉宽调制下并联H桥DC/DC变换器时,可以实现开关管的零电压开通和零电流关断。     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Alternate forms of the PWM switch models

Vorperian's pulsewidth modulation (PWM) switch model consists of a PWM transformer and a nonlinear resistor. The recognition that any of the three transformer terminals can serve as the common terminal leads to two alternate PWM transformer models and the corresponding two alternate PWM switch models. For a given PWM dc-dc converter, one of the three PWM switch models is more “natural” for graphic-oriented analysis/design, e.g., it allows the idealized converter to be analyzed by inspection. Furthermore, all three PWM transformers may be used to graphically manipulate the converter circuit to a form that can be analyzed by inspection. The alternate forms of the PWM transformers and the PWM switch models are effective as graphic-oriented teaching and learning tools for PWM converters. This is demonstrated using examples based on the boost converter and the Cuk converter     

Buck modulator with improved large-power bandwidth

A dynamic pulsewidth modulator (DPM) is synthesized to generate a PWM (pulsewidth modulated) signal from dynamic converter variables and from a (quasi-)static control signal. Based on a pragmatic principle with simple hardware implementation, the DPM can be functionally integrated with a PWM converter to broaden the converter power bandwidth, enhancing the converter's ability to meet stringent dynamic specifications. Even if bandwidth broadening is not the prime objective, the smaller phase shift associated with the broader bandwidth simplifies the design of the regulation loop. The DPM principle can also linearize the large-signal behavior of a nonlinear converter. The theory is demonstrated and verified for a buck converter, whose PWM bandwidth is extended from 1/50 of the switching frequency to about 1/3 of the switching frequency.     

基于TMS320F2812生成移相PWM的2种办法

移相 PWM波是很多开关电源常用的驱动脉冲信号。双向全桥直流变换器(Bidirectional-Full-Bridge DCDC Converter,BDC)在双重移相控制方式下时需要 4组两两互补的移相 PWM波。文章基于 TMS320F2812型 DSP(Digital Signal Processor)分析了 2种生成移相 PWM的方法。为提高双向全桥直流变换器工作的安全性和可靠性,为移相 PWM波设置死区时间。对所提出的方法进行测试后结果良好,对于双向全桥直流变换器闭环控制系统的构建具有重要意义。