共查询到15条相似文献,搜索用时 562 毫秒
1.
为了研究飞机减摆器中油液压缩性对摆振稳定性的影响,以某型无人机前起落架为研究对象,在建立液压缸压力微分方程的基础上,采用LMS Imagine.Lab AMESim建立飞机减摆器液压模型,利用该模型对减摆器动态阻尼特性进行仿真分析。基于多体动力学理论,采用LMS Virtual.Lab Motion建立前起落架摆振动力学模型。联合上述两种模型进行飞机滑跑虚拟试验,得到不同油液压缩性时飞机摆角的动态响应曲线。结果表明:当油液含气量从0.05%增大到0.50%时,功量图面积减少了44%,增大油液含气量极大地减小了减摆器的阻尼性能,尤其是在小振幅、低频率的工况下;摆振稳定性对油液的压缩性相当敏感,不太大的油液含气量(大于0.19%)足以使摆振不稳定。 相似文献
2.
3.
4.
5.
详细推导了摩擦式减摆器的摩擦阻尼力矩和实际当量阻尼公式,分析了其阻尼特性。一方面,摩擦式减摆器的摩擦阻尼力矩跟速度无关,在结构尺寸及摩擦系数确定的情况下,只跟载荷相关。另一方面,摩擦式减摆器的实际当量阻尼随着载荷的增大而增大,随着摆振频率的增大而减小,随着摩擦系数的增大而增大。这种摩擦式减摆器安装在一种支柱式起落架上,其提供的实际当量阻尼在小载荷的情况下小于临界当量阻尼,滑跑速度大于6m/s时起落架有摆振的风险。在大载荷的情况下实际当量阻尼大于临界当量阻尼,起落架不会摆振。 相似文献
6.
轮胎刚度作为轮胎动力学模型的重要参数之一,研究其对大型民机前起落架摆振的影响规律,可以从前起落架防摆设计的角度为轮胎刚度设计提供参考依据。基于前起落架摆振非线性数学模型,使用Matlab/Matcont 软件计算不同轮胎扭转刚度、轮胎侧弯刚度下的摆振区域图;研究轮胎扭转刚度、轮胎侧弯刚度对前起落架摆振的影响规律,并对比二者对前起落架摆振影响的敏感度。结果表明:对前起落架摆振影响的敏感性,轮胎扭转刚度大于轮胎侧弯刚度;轮胎回正力矩系数每减小1%,扭转摆振最大临界阻尼减小0.88%,侧向摆振中速区最小临界减摆阻尼增大33.87%;减小轮胎扭转刚度,增大轮胎侧弯刚度有利于抑制大型民机前起落架摆振。 相似文献
7.
在研究主起落架支柱在刹车状态下摆振的过程中,我们以双轮支柱式主起落架为例,同时,考虑到了其在纵向振动及扭转振动时自动防滑系统(ABS)的工作情况^[1]。本文在做了一些必要的假设条件下,引入了与起落架机轮,缓冲支柱及减摆器相关的变量和参数,并推导出主起落架刹车机轮振动的数学模型,进而研究与缓冲支柱和机轮参数相关的摆振激发主发生摆振的稳定区域边界。 相似文献
8.
在非惯性坐标系中建立了起落架支柱的动力学模型。与飞机地面运行的六自由度模型结合,可以考察非直线滑跑飞机的起落架摆振现象及飞机地面滑行的方向稳定性。以K8飞机为例,考察了非直线滑跑模型与传统的直线滑跑模型的摆振特点及飞机的滑跑稳定性。算例结果合理,表明模型可供有关研究参考。 相似文献
9.
10.
11.
飞机主起落架机轮摆振分析 总被引:1,自引:0,他引:1
针对××型飞机主起落架上、下扭力臂之间装有附加阻尼器的特殊方案,分析了主起落架机轮摆振问题,讨论了各种参数的变化对防止摆振的作用,结果表明附加阻尼器对防止摆振的必要性和有效性。同时,又对该型飞机采用4轮小车式主起落架的改型方案,验证了去掉原来附加阻尼器的合理性。 相似文献
12.
Zhou Jinxiong 《中国航空学报》1998,(3):185-191
PARAMETRICSHIMMYANALYSISZhouJinxiong(周进雄),ZhuDepei(诸德培)(Dept.ofAircraftEnginering,NorthwesternPolytechnicalUniversity,Xi′an,7... 相似文献
13.
14.
Gear walk instability studies using flexible multibody dynamics simulation methods in SIMPACK 总被引:1,自引:0,他引:1
《Aerospace Science and Technology》2006,10(1):19-25
In a variety of mechanical systems friction induced vibrations are a major concern. The aircraft landing gear is by nature a complex multidegree-of-freedom dynamic system. It may encounter various vibration modes which can be induced by brake frictional characteristics and design features. These brake induced oscillations can lead to very high loads in the landing gear and brake structure which may result in passenger discomfort and sometimes in component failure. Along with the serious fore and aft oscillations of a landing gear, often referred to as gear walk, chatter, squeal, shimmy and other vibrations in aircraft landing systems are not only annoying and disconcerting but can also affect the stability of the plane during take-off, landing, and rolling. In this paper, simulation of such an unstable and complex phenomenon during aircraft ground maneuvers is done to detect vibrations in aircraft landing gear. A commercial multibody simulation tool SIMPACK is used for this purpose. The article is based on work done in co-operation between DLR and Liebherr Aerospace. 相似文献
15.
A mathematical model and a technique for calculating the rolling motion stability of the damper-equipped landing gear wheel are presented; the dependence of dynamic damper rigidity on frequency found experimentally is used in the investigation. The results of calculating the shimmy boundaries with and without regard for the dependence indicated are given. 相似文献