非正侧视阵列机载雷达多空间角补偿算法

 非正侧阵列机载雷达的杂波分布随距离变化而变化,各距离单元的杂波分布不再满足独立同分布条件,造成统计型空时自适应处理(STAP)处理器性能下降。本文提出了一种多空间角补偿(MSAC)的非正侧视机载雷达杂波抑制方法,该方法先通过角度-多普勒补偿(ADC)预处理以消除在谱中心处的杂波非均匀,然后采用MSAC法在多个多普勒方向使参考单元和待检测单元的杂波谱保持一致,从而进一步消除在其余方位的杂波非均匀。仿真结果表明了该方法的性能明显优于ADC法,且运算量增加不多。     

一种基于角度-多普勒补偿的均匀圆形天线机载雷达杂波抑制方法

采用均匀圆形相控阵天线的机载雷达杂波分布随距离变化而变化,各距离单元的杂波不再满足独立同分布的条件,造成统计型空时自适应处理(STAP)器性能下降。基于此,本文建立了均匀圆形天线机载雷达模型,对其杂波分布进行了分析,得出了空间角随阵元数非线性变化的特性造成其杂波距离维分布非均匀的结论。研究了一种均匀圆形天线机载雷达杂波抑制方法,该方法先通过修正的角度 多普勒补偿(MADC)预处理消除在杂波谱中心处的非均匀,再利用基于导数更新(DBU)技术进一步减小在其他方位杂波的非均匀程度。仿真结果表明了该方法的有效性。     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

Adaptive Radar Detection in Doubly Nonstationary Autoregressive Doppler Spread Clutter

The problem of adaptive radar detection in clutter which is nonstationary both in slow and fast time is addressed. Nonstationarity within a coherent processing interval (CPI) often precludes target detection because of the masking induced by Doppler spreading of the clutter. Across range bins (i.e., fast time), nonstationarity severely limits the amount of training data available to estimate the noise covariance matrix required for adaptive detection. Such difficult clutter conditions are not uncommon in complex multipath propagation conditions where path lengths can change abruptly in dynamic scenarios. To mitigate nonstationary Doppler spread clutter, an approximation to the generalized likelihood ratio test (GLRT) detector is presented wherein the CPI from the hypothesized target range is used for both clutter estimation and target detection. To overcome the lack of training data, a modified time-varying autoregressive (TVAR) model is assumed for the clutter return. In particular, maximum likelihood (ML) estimates of the TVAR parameters, computed from a single snapshot of data, are used in a GLRT for detecting stationary targets in possibly abruptly nonstationary clutter. The GLRT is compared with three alternative methods including a conceptually simpler ad hoc approach based on extrapolation of quasi-stationary data segments. Detection performance is assessed using simulated targets in both synthetically-generated and real radar clutter. Results suggest the proposed GLRT with TVAR clutter modeling can provide between 5–8 dB improvement in signal-to-clutter plus noise ratio (SCNR) when compared with the conventional methods.     

Radar detection in clutter

Clutter is defined as any unwanted radar return. The presence of clutter in a range/Doppler cell complicates the detection of a target return signal in that cell. In order to quantify the effect of clutter on the probability of detection, we must first specify sets of models suitable for representing the clutter and target. The simplest and most common model for clutter is based on the gamma density. We include two additional models, the NCG and NCGG clutter models for low grazing angles. They are motivated by physical arguments, the latter of which can accommodate the well-known phenomenon of speckle. Using one of these models for clutter together with one of several models for targets, we determine, in a range/Doppler cell, expressions for probabilities of detection of a target in the presence of clutter. It is important to control the probability of false alarms. The presence of clutter in a cell necessitates an increase in the detection threshold setting in order to control false alarms, thus lowering the probability of detection. If the clutter level is unknown, then we need to take measurements of the clutter and use it to adjust the threshold. The more clutter samples we take, the better the estimate of the clutter level and the less is the resulting detection loss. Using the expressions for the probability of detection in clutter, we can quantify the detection loss for a pair of commonly used constant false-alarm rate (CFAR) techniques and investigate how the loss varies with different parameter values, especially with regard to the number of clutter samples taken to estimate the clutter level.     

一种基于角度-多普勒补偿的均匀圆形

采用均匀圆形相控阵天线的机载雷达杂波分布随距离变化而变化,各距离单元的杂波不再满足独立同分布的条件,造成统计型空时自适应处理(STAP)器性能下降。基于此,本文建立了均匀圆形天线机载雷达模型,对其杂波分布进行了分析,得出了空间角随阵元数非线性变化的特性造成其杂波距离维分布非均匀的结论。研究了一种均匀圆形天线机载雷达杂波抑制方法,该方法先通过修正的角度-多普勒补偿(MADC)预处理消除在杂波谱中心处的非均匀,再利用基于导数更新(DBU)技术进一步减小在其他方位杂波的非均匀程度。仿真结果表明了该方法的有效性。     

HRR Detector for Slow-Moving Targets in Sea Clutter

The radar detection of targets in the presence of sea clutter has historically relied upon the radial velocity of targets with respect to the radar platform either by exploiting the relative target Dopplers (for targets with sufficient radial velocity) or by discerning the paths targets traverse from scan to scan. For targets with little to no radial velocity component, though, it can become quite difficult to differentiate targets from the surrounding sea clutter. This paper addresses the detection of slow-moving targets in sea clutter using a high resolution radar (HRR) such that the target has perceptible extent in range. Under the assumption of completely random sea clutter spikes based on an epsiv-contaminated mixture model with the signal and clutter powers known, optimal detection performance results from using the likelihood ratio test (LRT). However, for realistic sea clutter, the clutter spikes tend to be a localized phenomenon. Based upon observations from real radar data measurements, a heuristic approach exploiting a salient aspect of the idealized LRT is developed which is shown to perform well when applied to real measured sea clutter.     

A Model for Generating Synthetic VHF SAR Forest Clutter Images

We propose a model for generating low-frequency synthetic aperture radar (SAR) clutter that relates model parameters to physical characteristics of the scene. The model includes both distributed scattering and large-amplitude discrete clutter responses. The model also incorporates the SAR imaging process, which introduces correlation among image pixels. The model may be used to generate synthetic clutter for a range of environmental operating conditions for use in target detection performance evaluation of the radar and automatic target detection/recognition algorithms. We derive a statistical representation of the proposed clutter model's pixel amplitudes and compare with measured data from the CARABAS-II SAR. Simulated clutter images capture the structure and amplitude responses seen in the measured data. A statistical analysis shows an order of magnitude improvement in model fit error compared with standard maximum-likelihood (ML) density fitting methods.     

Spiky sea clutter at high range resolutions and very low grazingangles

X-band (9.5-10.0 GHz) backscatter at near grazing incidence (0.2 deg) from the sea off the coast of Kauai, Hawaii, was measured with a radar characterized by a high spatial resolution in range (0.3 m) and a high temporal resolution (2000 Hz pulse repetition frequency (PRF)). Extensive amounts (over 20 min per measurement) of vertically and horizontally polarized sea clutter data were taken with upwind (UP) and crosswind (CR) transmit geometries during the collection campaign. Specific but representative examples of the clutter were statistically and phenomenologically analyzed over time scales varying from long (200 s), to intermediate (5 s), to short (50 ms), and over range swaths varying from full (160 m), to partial (30 m), to a single range cell (0.3 m). All analyses and results presented here are noncoherent, involving only the clutter amplitudes. Each type of clutter exhibited the characteristic spiky behavior which has come to be expected from microwave sea backscatter observed at low grazing angles and high range resolutions, while showing, between themselves, marked transmit geometry and polarization dependent contrasts, with the horizontally polarized clutter, measured with an UP transmit geometry, being especially notable for its frequently occurring, significant high frequency spectral content. Within the same clutter type, differences were observed in the probability distributions of radar cross sections (RCS) of spatially and temporally extended spiking events     

An effect of range-heterogeneous clutter on adaptive Dopplerfilters

The practical implementation of adaptive Doppler filters requires estimates of clutter parameters to determine the adaptive weights. A method of deriving the estimate via the sample matrix inversion (SMI) algorithm using multiple data snapshots from adjacent range cells is presented. For homogeneous clutter environments, the results of this technique asymptotically approach the optimum (a priori known covariance matrix) as the number of snapshots approaches infinity; this asymptotic behavior does not occur for heterogeneous clutter environments. An equation for the decrease in improvement factor is derived. To promote understanding, the simplified special case of narrowband clutter is considered in detail. In almost all cases, the loss is small     

Comparison between monostatic and bistatic antenna configurationsfor STAP

The unique characteristics of bistatic radar operation on the performance of airborne/spaceborne moving target indicator (MTI) radars that use space-time adaptive processing (STAP) are discussed. It has been shown that monostatic STAP radar has the following properties. 1) For a horizontal flight path and a planar Earth the curves of constant clutter Doppler (isodops) are hyperbolas. 2) For a sidelooking antenna geometry the clutter Doppler is range independent. 3) Clutter trajectories in the cosφ-F plane (F=normalized Doppler) are in general ellipses (or straight lines for a sidelooking array). We demonstrate that these well-known properties are distorted by the displacement between transmitter and receiver in a bistatic configuration. It is shown that even for the sidelooking array geometry the clutter Doppler is range-dependent which requires adaptation of the STAP processor for each individual range gate. Conclusions for the design of STAP processors are drawn     

Spatially distributed target detection in non-Gaussian clutter

Two detection schemes for the detection of a spatially distributed, Doppler-shifted target in non-Gaussian clutter are developed. The non-Gaussian clutter is modeled as a spherically invariant random vector (SIRV) distribution. For the first detector, called the non-scatterer density dependent generalized likelihood ratio test (NSDD-GLRT), the detector takes the form of a sum of logarithms of identical functions of data from each individual range cell. It is shown under the clutter only hypothesis, that the detection statistic has the chi-square distribution so that the detector threshold is easily calculated for a given probability of false alarm P_F. The detection probability P_D is shown to be only a function of the signal-to-clutter power ratio (S/C)_opt of the matched filter, the number of pulses N, the number of target range resolution cells J, the spikiness of the clutter determined by a parameter of an assumed underlying mixing distribution, and P_F. For representative examples, it is shown that as N, J, or the clutter spikiness increases, detection performance improves. A second detector is developed which incorporates a priori knowledge of the spatial scatterer density. This detector is called the scatterer density dependent GLRT (SDD-GLRT) and is shown for a representative case to improve significantly the detection performance of a sparsely distributed target relative to the performance of the NSDD-GLRT and to be robust for a moderate mismatch of the expected number of scatterers. For both the NSDD-GLRT and SDD-GLRT, the detectors have the constant false-alarm rate (CFAR) property that P_F is independent of the underlying mixing distribution of the clutter, the clutter covariance matrix, and the steering vector of the desired signal     

On Weibull-Distributed Weather Clutter

Weather clutter was observed using an L band range (200nmi) air-route surveillance radar (ARSR). It is shown that the measured clutter amplitudes obey a Weibull distribution.     

Time-frequency method for detecting an accelerating target in sea clutter

The authors design a time-frequency (TF) method for use in high-frequency surface-wave radar (HFSWR) for detecting a small accelerating target in sea clutter. The clutter is modelled by pseudo targets moving with Bragg velocity towards and away from the radar. The design is based on the Wigner distribution (WD) defined by Chan (type-III WD, in our terminology) rather than the WD defined by Claasen and Mecklenbrauker (1980) (2times type-I WD, in our terminology). Like the type-I WD, the type-III WD also concentrates a chirp signal onto a straight line in the TF plane. The type-III WD has the following advantages: 1) Its range of unambiguously measurable frequencies (RUMF) is [-pi,pi] rad/s, whereas for the type-I WD the RUMF is [-pi/2,pi/2] rad/s. 2) It allows a target separated from the clutter by pi rad/s to be detected, whereas the type-I WD coalesces such a target with the clutter and thereby mask it. An ambiguity function (AF) was defined corresponding to the type-III WD and use it to derive a smoothed type-III WD that mitigates the clutter. The smoothed type-III WD method is applied to real radar data and shown to be superior to the conventional Fourier transform method. The advantages of the type-III WD over the type-I WD are also demonstrated. The design principles laid out in the paper can also be used to develop a TF method for use in air traffic control radar (ATCR) for detecting an accelerating target in land clutter     

Doppler Processor Rejection of Range Ambiguous Clutter

Doppler processors are used in radar to separate target returns from clutter. When the clutter is at a range farther than the unambiguous range of the radar, the ability to reject the clutter is degraded. In this article the degradation is analyzed for an N-pulse batch processor with Dolph weighting, and the results show how degradation varies with design sidelobe level.     

扫描模式航管监视雷达风电场杂波检测与抑制

近年来,全球风力发电装机容量呈指数增长。研究表明,风轮机对其附近的航管(ATC)监视雷达会产生严重影响。风轮机杂波的有效检测及抑制,对于保证空中交通安全具有重要意义。首先提出了基于回波谱宽特征的航管监视雷达的风轮机杂波检测方法。针对扫描模式下航管监视雷达频谱分辨率较低的问题,将基于自回归(AR)模型的超分辨率方法和质量中心的概念应用于雷达回波的快速谱宽和谱中心估计算法中,提高谱宽估计的精度。其次针对扫描模式下的风轮机回波数据不是一个完整周期数据的问题,基于缺省数据幅度和相位估计(GAPES)算法实现了扫描模式下风轮机雷达回波缺省数据的估计,而后利用风轮机杂波的周期性抑制风轮机杂波。该算法实现了风轮机杂波的有效检测和抑制,并且其不受限于风轮机与飞机目标在同一个距离单元的情况。仿真结果验证了所提方法的有效性。     

Algorithms for Spatial Laser Beacon Acquisition

The pointing system for optical data transmission over unguided channels uses a return beacon from the receiver back to the transmitter to aid the reciprocal alignment of the two stations. We concentrate on CW or pulsed-beacon acquisition with array detectors in the presence of extended clutter in addition to background and receiver noises. Acquisition in the presence of a single interferer (jammer) is also considered. A maximum likelihood (ML) approach is used when preliminary scene information is available. In the case of unknown scenario, a picture-picture subtraction algorithm is considered for the pulsed laser. Performance is evaluated in terms of probability of an acquisition error for Poisson statistics of the photodetector output.     

Clutter Performance of Coherent Pulse Trains for Targets with Range Acceleration

The clutter performance of coherent pulse trains is examined when the duration of the pulse train is increased to values for which range acceleration effects must be taken into account. The problem of target detection against a clutter background with differential Doppler is studied in terms of the range acceleration effects on the conventional Doppler response. Specifically considered are the consequences on the sidelobe level and width of the main Doppler lobe. The analysis shows that the sidelobe level remains essentially unchanged when the range acceleration mismatch becomes significant. However, the main Doppler response broadens in proportion to the magnitude of the acceleration mismatch. Thus, an increase of the signal duration for better Doppler resolution is useful only until acceleration effects spread the Doppler spectrum of the clutter and eliminate the differential Doppler between targets and clutter.     

A Generalized Clutter Computation Procedure for Airborne Pulse Doppler Radars

A general procedure for analyzing ground clutter effects in airborne pulse Doppler radars is described. The quantity computed is the expected clutter power at the output of any specified range gate/ Doppler filter processing cell. The procedure has been computerized and is quite general with respect to antenna gain pattern, clutter cross section variation, PRF, pulse and range gate shapes, and the various receiver processing functions. It is applicable only to distributed ground clutter and linear processing, and excludes the dynamic effects of continuous antenna scanning. To exemplify the use of the procedure, two studies conducted for a postulated high PRF radar are described, and the results are presented.     

Multiple moving target feature extraction for airborne HRR radar

This study considers the clutter suppression and feature extraction of multiple moving targets for airborne high range resolution (HRR) phased array radar. To avoid the range migration problems that occur in the HRR radar data, we divide each HRR profile into nonoverlapping low range resolution segments. No information is lost due to the division and hence no loss of resolution occurs. We show how to use a vector auto-regressive filtering technique to suppress the clutter. Then a relaxation-based parameter estimation algorithm is presented for multiple moving target feature extraction. Numerical results are given to demonstrate the effectiveness of the algorithm