Venus surface power and cooling systems

A mission to the surface of Venus would have high scientific value, but most electronic devices and sensors cannot operate at the 450 °C ambient surface temperature of Venus. Power and cooling systems were analyzed for Venus surface operation. A radioisotope power and cooling system was designed to provide electrical power for a probe operating on the surface of Venus. For a mission duration of substantial length, the use of thermal mass to maintain an operable temperature range is likely impractical, and active refrigeration may be required to keep components at a temperature below ambient. Due to the high thermal convection of the high-density atmosphere, the heat rejection temperature was assumed to be at a 500 °C radiator temperature, 50 °C above ambient. The radioisotope Stirling power converter designed produces a thermodynamic power output capacity of 478.1 W, with a cooling power of 100 W. The overall efficiency is calculated to be 23.36%. The mass of the power converter is estimated at approximately 21.6 kg.     

Deployment history and design considerations for space reactor power systems

The history of the deployment of nuclear reactors in Earth orbits is reviewed with emphases on lessons learned and the operation and safety experiences. The former Soviet Union's “BUK” power systems, with SiGe thermoelectric conversion and fast neutron energy spectrum reactors, powered a total of 31 Radar Ocean Reconnaissance Satellites (RORSATs) from 1970 to 1988 in 260 km orbit. Two of the former Soviet Union's TOPAZ reactors, with in-core thermionic conversion and epithermal neutron energy spectrum, powered two Cosmos missions launched in 1987 in ～800 km orbit. The US’ SNAP-10A system, with SiGe energy conversion and a thermal neutron energy spectrum reactor, was launched in 1965 in 1300 km orbit. The three reactor systems used liquid NaK-78 coolant, stainless steel structure and highly enriched uranium fuel (90–96 wt%) and operated at a reactor exit temperature of 833–973 K. The BUK reactors used U-Mo fuel rods, TOPAZ used UO₂ fuel rods and four ZrH moderator disks, and the SNAP-10A used moderated U-ZrH fuel rods. These low power space reactor systems were designed for short missions (～0.5 kW_e and ～1 year for SNAP-10A, <3.0 kW_e and <6 months for BUK, and ～5.5 kW_e and up to 1 year for TOPAZ). The deactivated BUK reactors at the end of mission, which varied in duration from a few hours to ～4.5 months, were boosted into ～800 km storage orbit with a decay life of more than 600 year. The ejection of the last 16 BUK reactor fuel cores caused significant contamination of Earth orbits with NaK droplets that varied in sizes from a few microns to 5 cm. Power systems to enhance or enable future interplanetary exploration, in-situ resources utilization on Mars and the Moon, and civilian missions in 1000–3000 km orbits would generate significantly more power of 10's to 100's kW_e for 5–10 years, or even longer. A number of design options to enhance the operation reliability and safety of these high power space reactor power systems are presented and discussed.     

Super-capacitor energy storage for micro-satellites: Feasibility and potential mission applications

Small satellites, weighting between 100 and 200 kg, have witnessed increasing use for a variety of space applications including remote sensing constellations and technology demonstrations. The energy storage/stored power demands of most spacecraft, including small satellites, are currently accommodated by rechargeable batteries—typically nickel–cadmium cells (specific energy of 50 Wh kg⁻¹), or more recently lithium-ion cells (150 Wh kg⁻¹). High energy density is a primary concern for spacecraft energy storage design, and these batteries have been sufficient for most applications. However, constraints on the allowable on-board battery size have limited peak power performance such that the maximum power supply capability of small satellites currently ranges between only 70 and 200 W. This relatively low maximum power limits the capabilities of small satellites in terms of payload design and selection. In order to enhance these satellites' power performance, the research reported in this paper focused on the implementation of super-capacitors as practical rechargeable energy storage medium, and as an alternative to chemical batteries. Compared to batteries, some super-capacitors are able to supply high power at high energy-efficiency, but unfortunately they still have a very low energy density (5–30 Wh kg⁻¹). However, the provision of this high power capability would considerably widen the range of small satellite applications.     

Endurance testing of a pulsed plasma thruster for nanosatellites

The mission complexity of Nanosatellites has increased tremendously in recent years, but their mission range is limited due to the lack of an active orbit control or ∆v capability. Pulsed Plasma Thrusters (PPT), featuring structural simplicity and very low power consumption are a prime candidate for such applications. However, the required miniaturization of standard PPTs and the adaption to the low power consumption is not straightforward. Most investigated systems have failed to show the required lifetime. The present coaxial design has shown a lifetime of up to 1 million discharges at discharge energies of 1.8 J in previous studies. The present paper focuses on performance characterizations of this design. For this purpose direct thrust measurements with a µN thrust balance were conducted. Thrust measurements in conjunction with mass bit determination allowed a comprehensive assessment. Based on those measurements the present µPPT has a total impulses capability of approximately I≈1.7 Ns, an average mass bit of 0.37 µg s⁻¹ and an average specific impulse of I_sp≈904 s. All tests have shown very good EM compatibility of the PPT with the electronics of the flight-like printed circuit board. Consequently, a complete µPPT unit can provide a ∆v change of 5.1 m/s or 2.6 m/s to a standard 1-unit or 2-unit CubeSat respectively.     

Very high delta-V missions to the edge of the solar system and beyond enabled by the dual-stage 4-grid ion thruster concept

A new and innovative type of gridded ion thruster, the “Dual-Stage 4-Grid” or DS4G concept, has been proposed and its predicted high performance validated under an ESA research, development and test programme. The DS4G concept is able to operate at very high specific impulse and thrust density values well in excess of conventional 3-grid ion thrusters at the expense of a higher power-to-thrust ratio. This makes it a possible candidate for ambitious missions requiring very high delta-V capability and high power. Such missions include 100 kW-level multi-ton probes based on nuclear and solar electric propulsion (SEP) to distant Kuiper Belt Object and inner Oort cloud objects, and to the Local Interstellar medium. In this paper, the DS4G concept is introduced and its application to this mission class is investigated. Benefits of using the DS4G over conventional thrusters include reduced transfer time and increased payload mass, if suitably advanced lightweight power system technologies are developed.A mission-level optimisation is performed (launch, spacecraft system design and low-thrust trajectory combined) in order to find design solutions with minimum transfer time, maximum scientific payload mass, and to explore the influence of power system specific mass. It is found that the DS4G enables an 8-ton spacecraft with a payload mass of 400 kg, equipped with a 65 kW nuclear reactor with specific mass 25 kg/kW (e.g. Topaz-type with Brayton cycle conversion) to reach 200 AU in 23 years after an Earth escape launch by Ariane 5. In this scenario, the optimum specific impulse for the mission is over 10,000 s, which is well within the capabilities of a single 65 kW DS4G thruster. It is also found that an interstellar probe mission to 200 AU could be accomplished in 25 years using a “medium-term” SEP system with a lightweight 155 kW solar array (2 kg/kW specific mass) and thruster PPU (3.7 kg/kW) and an Earth escape launch on Ariane 5. In this case, the optimum specific impulse is lower at 3500 s which is well within conventional gridded ion thruster capability.     

Development of an integrated countermeasure device for use in long-duration spaceflight

Prolonged weightlessness is associated with declines in musculoskeletal, cardiovascular, and sensorimotor health. Consequently, in-flight countermeasures are required to preserve astronaut health. We developed and tested a novel exercise countermeasure device (CCD) for use in spaceflight with the aim of preserving musculoskeletal and cardiovascular health along with an incorporated balance training component. Additionally, the CCD features a compact footprint, and a low power requirement. Methods: After design and development of the CCD, we carried out a training study to test its ability to improve cardiovascular and muscular fitness in healthy volunteers. Fourteen male and female subjects (41.4±9.0 years, 69.5±15.4 kg) completed 12 weeks (3 sessions per week) of concurrent strength and endurance training on the CCD. All training was conducted with the subject in orthostasis. When configured for spaceflight, subjects will be fixed to the device via a vest with loop attachments secured to subject load devices. Subjects were tested at baseline and after 12 weeks for 1-repetition max leg press strength (1RM), peak oxygen consumption (VO_2peak), and isokinetic joint torque (ISO) at the hip, knee, and ankle. Additionally, we evaluated subjects after 6 weeks of training for changes in VO_2peak and 1RM. Results: VO_2peak and 1RM improved after 6 weeks, with additional improvements after 12 weeks (1.95±0.5, 2.28±0.5, 2.47±0.6 L min^?1, and 131.2±63.9,182.8±75.0, 207.0±75.0 kg) for baseline, 6 weeks, and 12 weeks, respectively. ISO for hip adduction, adduction, and ankle plantar flexion improved after 12 weeks of training (70.3±39.5, 76.8±39.2, and 55.7±21.7 N m vs. 86.1±37.3, 85.1±34.3, and 62.1±26.4 N m, respectively). No changes were observed for ISO during hip flexion, knee extension, or knee flexion. Conclusions: The CCD is effective at improving cardiovascular fitness and isotonic leg strength in healthy adults. Further, the improvement in hip adductor and abductor torque provides support that the CCD may provide additional protection for the preservation of bone health at the hip.     

MOA2—an R&D paradigm buster enabling space propulsion by commercial applications

More than 60 years after the late Nobel laureate Hannes Alfvén had published a letter stating that oscillating magnetic fields can accelerate ionised matter via magneto–hydrodynamic interactions in a wave like fashion, the technical implementation of Alfvén waves for propulsive purposes has been proposed, patented and examined for the first time by a group of inventors.Consequently improved since then, the name of the latest concept, relying on magneto-acoustic waves to accelerate electric conductive matter, is MOA²—Magnetic field Oscillating Amplified Accelerator. Based on computer simulations, which were undertaken to get a first estimate on the performance of the system, MOA² is a corrosion free and highly flexible propulsion system, whose performance parameters might easily be adapted in operation, by changing the mass flow and/or the power level. As such the system is capable of delivering a maximum specific impulse of 13116 s (12.87 mN) at a power level of 11.16 kW, using Xe as propellant, but can also be attuned to provide a thrust of 236.5 mN (2411 s) at 6.15 kW of power. First tests—that are further described in this paper—have been conducted successfully with a 400 W prototype system at an ambient pressure of 0.20 Pa, delivered 9.24 mN of thrust at 1472 s I_SP, thereby underlining the feasibility of the concept.Based on these results, space propulsion is expected to be a prime application for MOA²—a claim that is supported by numerous applications such as Solar and/or Nuclear Electric Propulsion or even as an ‘afterburner system’ for Nuclear Thermal Propulsion. However, MOA² has so far seen most of its R&D impetus from terrestrial applications, like coating, semiconductor implantation and manufacturing as well as steel cutting. Based on this observation, MOA² resembles an R&D paradigm buster, as it is the first space propulsion system, whose R&D is driven primarily by its terrestrial applications. Different terrestrial applications exist, but the most successful scenarios so far revolve around MOA²'s unique features with respect to high throughput/low target temperature coatings on sensitive materials. In combination with its intrinsic high flexibility, MOA² is highly suited for a common space-terrestrial application research and utilisation strategy.This paper presents the recent developments of the MOA² R&D activities at Q₂ Technologie(s), the company in Vienna, Austria, which has been set up to further develop and test the magneto-acoustic wave technology and its applications.     

Investigation of nuclear electric powered interstellar precursor missions

Nuclear Electric Propulsion (NEP) is a technology conceptually proposed since the 1940s by E. Stuhlinger in Germany. The JIMO mission originally planned by NASA in the early 2000s produced at least two designs of ion thrusters fed by a 20–30 kW nuclear powerplant. When compared to conventional (chemical) propulsion, the major advantage of NEP in the JIMO context was recognized to be the much higher I_sp (lab-tested at up to 15,000 s) and the capability for sustained power generation, up to 8–10 years when derated to I_sp about 8000 s.The goal of this paper is to show that current or near term NEP technology enables missions far beyond our immediate interplanetary backyard. In fact, by extending the semi-analytical approach used by Stuhlinger, with reasonable ratios α≡power/mass of the propulsion system (i.e., 0.1– 0.4 kW/kg), missions to the Kuiper Belt (40 AU and beyond) and even the so-called FOCAL mission (at 540 AU) become feasible with an attractive payload fraction and in times of order 10–15 years.Further results regarding missions to Sedna’s perihelion/aphelion, and to Oort’s cloud will also be presented, showing the constraints affecting their feasibility and mass budget.     

On the capabilities of nano electrokinetic thrusters for space propulsion

A theoretical analysis considering the capabilities of nano electrokinetic thrusters for space propulsion is presented. The work describes an electro-hydro-dynamic model of the electrokinetic flow in nano-channels and represents the first attempt to exploit the advantages of the electrokinetic effect as the basis for a new class of nano-scale thrusters suitable for space propulsion. Among such advantages are their small volume, fundamental simplicity, overall low mass, and actuation efficiency. Their electrokinetic efficiency is affected by the slip length, surface charge, pH and molarity. These design variables are analyzed and optimized for the highest electrokinetic performance inside nano-channels. The optimization is done for power consumption, thrust and specific impulse resulting in high theoretical efficiency ∼99% with corresponding high thrust-to-power ratios. Performance curves are obtained for the electrokinetic design variables showing that high molarity electrolytes lead to high thrust and specific impulse values, whereas low molarities provide highest thrust-to-power ratios and efficiencies. A theoretically designed 100 nm wide by 1 μm long emitter optimized using the ideal performance charts developed would deliver thrusts from 5 to 43 μN, specific impulse from 60 to 210 s, and would have power consumption between 1–15 mW. It should be noted that although this is a detail analytical analysis no prototypes exist and any future experimental work will face challenges that could affect the final performance. By designing an array composed of thousands of these single electrokinetic emitters, it would result in a flexible and scalable propulsion system capable of providing a wide range of thrust control for different mission scenarios and maintaining very high efficiencies and thrust-to-power ratio by varying the number of emitters in use at any one time.     

Thrust measurement of dimethyl ether arcjet thruster

The present paper describes thrust measurement results for an arcjet thruster using Dimethyl ether (DME) as the propellant. DME is an ether compound and can be stored as a liquid due to its relatively low freezing point and preferable vapor pressure. The thruster successfully produced high-voltage mode at DME mass flow rates above 30 mg/s, whereas it yielded low-voltage mode below 30 mg/s. Thrust measurements yielded a thrust of 0.15 N and a specific impulse of 270 s at a mass flow rate of 60 mg/s with a discharge power of 1300 W. The DME arcjet thruster was comparable to a conventional one for thrust and discharge power.     

Development and evaluation of bioregenerative menus for Mars habitat missions

Two 10-day menus were developed in preparation for a Mars habitat mission. The first was built on the assumption, as in previous menu development efforts for closed ecological systems, that the food system would be vegetarian, whereas the second menu introduced shelf-stable, prepackaged meat and entrée items from the current International Space Station (ISS) food system. Both menus delivered an average of 3000 cal daily but the macronutrient proportions resulted in an excess of carbohydrates and dietary fiber per mission nutritional recommendations. Generally, the individual recipes comprising both menus were deemed acceptable by internal sensory panel (average overall acceptability=7.4). The incorporation of existing ISS entrée items did not have a significant effect on the acceptability of the menus. In a final comparison, the food system upmass, or the amount of food that is shipped from the Earth, increased by 297 kg with the addition of prepackaged entrées to the menu. However, the addition of the shipped massed was counterbalanced by a 864 kg reduction in required crops. A further comparison of the crew time required for meal preparation and farming, food system power requirements, and food processing equipment mass is recommended to definitively distinguish the menus.     

BBM/EM design of the thermal hyperspectral imager: An instrument for remote sensing of earth's surface,atmosphere and ocean,from a microsatellite platform

The Thermal Hyperspectral Imager (THI) is a low cost, low mass, power efficient instrument designed to acquire hyperspectral remote sensing data in the long-wave infrared. The instrument has been designed to satisfy mass, volume, and power constraints necessary to allow for its accommodation in a 95 kg micro-satellite bus, designed by staff and students at the University of Hawai'i. THI acquires approximately 30 separate spectral bands in the 8–14 μm wavelength region, at 16 wavenumber resolution. Rather than using filtering or dispersion to generate the spectral information, THI uses an interferometric technique. Light from the scene is focused onto an uncooled microbolometer detector array through a stationary interferometer, causing the light incident at each detector at any instant in time to be phase shifted by an optical path difference which varies linearly across the array in the along-track dimension. As platform motion translates the detector array in the along-track direction at a rate of approximately one pixel per frame (the camera acquires data at 30 Hz) the radiance from each scene element can be sampled at each OPD, thus generating an interferogram. Spectral radiance as a function of wavelength is subsequently obtained for each scene element using standard Fourier transform techniques. Housed in a pressure vessel to shield COTS parts from the space environment, the total instrument has a mass of 15 kg. Peak power consumption, largely associated with the calibration procedure, is <90 W. From a nominal altitude of 550 km the resulting data would have a spatial resolution of approximately 300 m. Although an individual imaging event yields approximately 1 Gbit of raw uncompressed data, onboard processing (to convert the interferograms into a conventional spectral hypercube) can reduce this to tens of Mega bits per scene. In this presentation we will describe (a) the rationale for the project, (b) the instrument design, and (c) how the data are processed. Finally we will present data acquired by THI on a laboratory microscope stage to demonstrate the spectro-radiometric quality of the data that the instrument can provide.     

Compensation of gravitational attraction disturbance to pure gravity orbit for Inner Formation Flying System

The Inner Formation Flying System (IFFS) consisting of an outer satellite and an inner satellite which is a solid sphere proof mass freely flying in the shield cavity can construct a pure gravity orbit to precisely measure the earth gravity field. The gravitational attraction on the inner satellite due to the outer satellite is a significant disturbance source to the pure gravity orbit and is required to be limited to 10⁻¹¹ m s⁻² order. However, the gravitational disturbance force was on 10⁻⁹ m s⁻² order actually and must be reduced by dedicated compensation mass blocks. The region of relative motion of the inner satellite about its nominal position is within 1 cm in dimension, which raises the complexity of the compensation blocks design. The iterative design strategy of the compensation blocks based on reducing the gravitational attraction at the nominal position of the inner satellite is presented, aiming to guarantee the gravitational force in the relative motion region within requirements after the compensation. The compensation blocks are designed according to the current status of IFFS, and the gravitational disturbance force in the region is reduced to 10⁻¹¹ ms⁻² order with minimized adding mass.     

Electromagnetic shielding of thermal protection system for hypersonic vehicles

The numerical simulation and the measurement of electromagnetic shielding at microwave frequencies of thermal protection system for hypersonic vehicles is presented using nested reverberation chamber. An example of a possible thermal protection system for a re-entry vehicle is presented. This system based on carbon material is electromagnetically characterized. The characterization takes into account not only the materials but also the final assembly configuration of the thermal protection system. The frequency range is 2–8 GHz. The results of measurements and simulations show that the microwave shielding effectiveness of carbon materials is above 60 dB for a single tile and that the tile inter-distance is able to downgrade the shielding effectiveness on the average to about 40 dB.     

Design and on-orbit performance of the attitude determination and control system for the ZDPS-1A pico-satellite

The ZDPS-1A pico-satellite, developed by the Zhejiang University, is featured with a three-axis stabilizing capability. It is 15×15×15 cm³ cube-shaped satellite with a total mass of 3.5 kg. ZDPS-1A is the first pico-satellite that has been launched successfully in China. The mission of ZDPS-1A is on-orbit system verification of student-build pico-satellite and wide range earth observation with a micro panoramic camera. A miniature momentum wheel is employed to offer gyro stiffness stability in the pitch (orbit normal) axis. Magnetic coils are employed to generate control torques to achieve the three-axis stabilization of nadir-pointing. The attitude sensors employed in the design include two three-axis magnetometers (TAMs), a three-axis gyro, and two sun sensors. Both ground simulations and on-orbit testing are conducted to verify the feasibility of the given attitude determination and control system (ADCS).     

Radiation engineering analysis of shielding materials to assess their ability to protect astronauts in deep space from energetic particle radiation

An analysis is performed on four typical materials (aluminum, liquid hydrogen, polyethylene, and water) to assess their impact on the length of time an astronaut can stay in deep space and not exceed a design basis radiation exposure of 150 mSv. A large number of heavy lift launches of pure shielding mass are needed to enable long duration, deep space missions to keep astronauts at or below the exposure value with shielding provided by the vehicle. Therefore, vehicle mass using the assumptions in the paper cannot be the sole shielding mechanism for long duration, deep space missions. As an example, to enable the Mars Design Reference Mission 5.0 with a 400 day transit to and from Mars, not including the 500 day stay on the surface, a minimum of 24 heavy lift launches of polyethylene at 89,375 lbm (40.54 tonnes) each are needed for the 1977 galactic cosmic ray environment. With the assumptions used in this paper, a single heavy lift launch of water or polyethylene can protect astronauts for a 130 day mission before exceeding the exposure value. Liquid hydrogen can only protect the astronauts for 160 days. Even a single launch of pure shielding material cannot protect an astronaut in deep space for more than 180 days using the assumptions adopted in the analysis. It is shown that liquid hydrogen is not the best shielding material for the same mass as polyethylene for missions that last longer than 225 days.     

Design and testing of a roto-translational shutter mechanism for planetary operation

This work describes the design and testing of a shutter mechanism for a miniaturized infrared spectrometer developed for the ESA ExoMars Pasteur mission. Unlike most usual cover mechanisms, the conceived one provides a roto-translational motion. This feature allows the sealing of the interferometer main entrance window from dust contamination, in addition to the usual function of shuttering the instrument field of view. Although this characteristic is strongly desired because it avoids dust deposition and optics contamination while the instrument is not operating, it makes the mechanism design significantly more complex. Moreover, challenging design constraints were faced: the mass budget allowed for no more than 30 g allocation, the expected working thermal range extended down to −80 °C and high vibration levels with an acceleration peak of 670 m/s² were predicted during Mars landing. To complete the picture, the mechanism cover was required to provide also a calibration target for the 2–25 μm spectral range of the spectrometer. The resulting system is made by a calibrating/shutter cover moved by a purposely designed out of plane cams system which provides the desired motion. A mechanism mockup was assembled and successfully tested in the predicted thermal and mechanical environments.     

Lunar Base 2015 Stage 1

This paper is a design study for a modular Lunar Base built of at least six cylindrical modules. For launching an ARIANE-Rocket with a payload of 12 ton can be used.To land the modules on the moon the author has designed a Teleoperated Rocket Crane, which is assembled in the Lunar Orbit. The modules are made of aluminium sheets, using a double-shell structure to protect a crew of eight astronauts from radiation, micrometeorites, heat and low temperatures during the lunar night.Lunar material (regolith) is used for shielding.     

Field emission performance of multiwalled carbon nanotubes for a low-power spacecraft neutraliser

Field electron emission from aligned multiwalled carbon nanotubes has been assessed to determine if the performance, defined by power consumption, lifetime and emission current, is suitable for use in spacecraft charge neutralisation for field emission electric propulsion (FEEP). Carbon nanotubes grown by chemical vapour deposition (CVD) were mounted on a dual in line chip with a macroscopic (nickel mesh) extractor electrode mounted ～1 mm above the tubes. The nanotubes’ field emission characteristics (emission currents, electron losses and operating voltage) were measured at ～10^?4 Pa. An endurance test of one sample, running at a software-controlled constant emission current lasted >1400 h, approaching the longest known FEEP thruster lifetime. The emission corresponds to a current density of ～10 mA/cm² at a voltage of 150 V. These results, implementing mature extractor-electrode geometry, indicate that carbon nanotubes have considerable potential for development as robust, low-power, long-lived electron emitters for use in space.     

Parabolic maneuvers of the Swiss Air Force fighter jet F-5E as a research platform for cell culture experiments in microgravity

Long-term sensitivity of human cells to reduced gravity has been supposed since the first Apollo missions and was demonstrated during several space missions in the past. However, little information is available on primary and rapid gravi-responsive elements in mammalian cells. In search of rapid-responsive molecular alterations in mammalian cells, short-term microgravity provided by parabolic flight maneuvers is an ideal way to elucidate such initial and primary effects. Modern biomedical research at the cellular and molecular level requires frequent repetition of experiments that are usually performed in sequences of experiments and analyses. Therefore, a research platform on Earth providing frequent, easy and repeated access to real microgravity for cell culture experiments is strongly desired. For this reason, we developed a research platform onboard the military fighter jet aircraft Northrop F-5E “Tiger II”. The experimental system consists of a programmable and automatically operated system composed of six individual experiment modules, placed in the front compartment, which work completely independent of the aircraft systems. Signal transduction pathways in cultured human cells can be investigated after the addition of an activator solution at the onset of microgravity and a fixative or lysis buffer after termination of microgravity. Before the beginning of a regular military training flight, a parabolic maneuver was executed. After a 1 g control phase, the parabolic maneuver starts at 13,000 ft and at Mach 0.99 airspeed, where a 22 s climb with an acceleration of 2.5g is initiated, following a free-fall ballistic Keplerian trajectory lasting 45 s with an apogee of 27,000 ft at Mach 0.4 airspeed. Temperature, pressure and acceleration are monitored constantly during the entire flight. Cells and activator solutions are kept at 37 °C during the entire experiment until the fixative has been added. The parabolic flight profile provides up to 45 s of microgravity at a quality of 0.05g in all axes. Access time is 30 min before take-off; retrieval time is 30 min after landing. We conclude that using military fighter jets for microgravity research is a valuable tool for frequent and repeated cell culture experiments and therefore for state-of-the art method of biomedical research.