影响GPS信号C／A码捕获的因素分析及改善方法

通过特定设计的软件测试平台,对自主研制的软件GPS接收机进行了捕获性能的测试分析,得到了捕获性能与信噪比、虚警概率等因素的关系。最后给出了实验数据和分析、改进方法,为软件GPS接收机的开发和研制提供了重要的技术参考。     

一种改进双块补零北斗导航接收机弱信号捕获方法

利用卫星导航系统对高轨航天器进行自主导航与高精度定轨,对接收机的捕获灵敏度要求极高,双块补零(DBZP)算法是无辅助下卫星导航弱信号捕获的理想方案,然而受限于数据处理量大,DBZP实际应用难度大。在深入分析双块补零机理的基础上,结合矩阵重构的思想,提出了一种改进双块补零北斗导航接收机弱信号捕获方法。该方法对参与块内相关运算的基带信号和本地测距码分别进行重构,解决了块内点数与快速傅里叶变换输入点数之间的矛盾,提高了北斗导航接收机弱信号捕获性能。仿真实验结果分析表明,改进双块补零算法对信噪比没有损失,可以保证对低至15dB·Hz的弱信号进行有效捕获,能够满足高轨航天器定轨、室内外无缝导航等对接收机高灵敏度的需求。本方法是在块内运算层面对DBZP进行优化,具备良好的通用性和可移植性,与优化相干积分策略的各种改进DBZP算法可以无缝对接,进一步提高北斗导航接收机信号处理的效能。同时,重构的思想也适用于其他采用码分多址信号的卫星导航系统的弱信号检测和捕获,对提升多星座卫星导航系统的基带信号处理性能具有参考意义。     

基于LEO辅助的北斗B1C高灵敏快速捕获算法

随着低轨(LEO)卫星数量的不断增加,利用LEO星座辅助增强GNSS导航性能已经成为一种新的趋势.针对低信噪比环境下B1C信号难以捕获的问题,提出了一种基于LEO辅助的B1C信号高灵敏快速捕获算法.首先对提升接收机捕获灵敏度进行了分析,对比了相干积分与非相干积分对于信号处理增益的影响,得出在低轨导航增强信号的辅助下采用增加相干积分时间的捕获算法对低信噪比条件下B1C信号的捕获更有效.然后提出了一种基于LEO辅助的B1C高灵敏快速捕获算法,从理论分析和实验仿真两方面,对比验证了在LEO辅助下可以显著提高B1C信号的捕获灵敏度,缩短捕获时间,提高捕获效率.     

一种盲多波束形成GNSS天线阵抗干扰算法

天线阵抗干扰是现代卫星导航接收机抗干扰的重要手段。传统的天线阵波束形成类算法能够在抑制干扰的同时提升抗干扰后输出信噪比,但是在信号捕获阶段,由于缺少先验信息的支持,该类算法无法在信号方向形成增益。因此,提出了一种盲多波束形成的天线阵抗干扰算法,通过形成多个波束覆盖天线阵上半球面,可在无先验信息的条件下对卫星信号形成增益,从而提升信号捕获阶段信噪比,使得接收机在干扰环境中具备更强的信号捕获能力。仿真结果表明:与传统的天线阵抗干扰算法相比,提出的算法能够在有效抑制干扰的同时显著提升接收机信号捕获成功率。     

通信辅助卫星导航接收机最优捕获灵敏度分析

通信辅助有助于降低卫星导航信号捕获的搜索模糊度,因此接收机可通过改进捕获算法 以提高捕获灵敏度。但是,目前在同等条件下捕获灵敏度提升量与通信辅助精度的量化关系尚不 明确。通过约束平均捕获时间和捕获算法计算复杂度两项指标的门限值,对接收机辅助信息精度 与捕获灵敏度提升量之间的关系进行量化分析,得出相应条件下的最优捕获算法参数。分析表 明,在频率搜索范围以1/2的幂次进行逐渐压缩的过程中,捕获灵敏度提升量最高约为4dB,且随 频率搜索范围压缩程度的提高而逐渐缩小。根据评估方法得到的最优捕获算法参数受捕获概率 指标、虚警概率指标等影响较小,可预置于接收机中,根据具体情况进行选择。     

北斗B1 QPSK调制信号的高灵敏度捕获算法

卫星信号在复杂环境中功率存在衰减,导致其低于接收机正常捕获范围,给信号捕获带来较大困难。在分析北斗B1频点信号体制及研究码并行捕获算法基础上,提出了针对北斗B1 QPSK调制信号的双通道并行搜索捕获算法,设计了优化的相干、非相干码并行捕获算法,解决了信噪比较低环境中北斗卫星信号捕获困难的问题。利用卫星信号模拟器产生的仿真信号对双通道并行捕获算法和相干、非相干累加捕获算法进行验证与分析,结果表明,前者性能明显优于单通道捕获,后者较普通捕获算法具有更理想的捕获灵敏度。     

一种高动态低信噪比卫星导航信号捕获方法

为提升高动态低信噪比环境下卫星导航信号的捕获性能,提出了一种基于分数阶傅里叶变换(FrFT)及部分匹配滤波(PMF)的捕获方法。在该方法中,接收机首先利用PMF对接收信号做分段相干积分,随后借助快速傅里叶变换(FFT)对分段积分结果做离散快速FrFT,最后通过检测FrFT输出的峰值完成信号的捕获。由于具有多普勒频率变化率的卫星导航信号在FrFT后呈现能量聚焦特性,所提方法能够显著提高信号的长时间相干积分增益。同时对所提算法的捕获概率、平均捕获时间以及算法复杂度等性能指标进行了理论分析及计算机仿真验证。仿真表明,与传统的PMF-FFT方法相比,所提方法能够通过延长相干积分时间的方式有效提升高动态低信噪比卫星导航信号的捕获概率、降低捕获时间。     

GNSS接收机在探月三期中的应用研究

探月工程对飞行器导航系统的性能提出了更高要求,因而有必要研究GNSS(Global Navigation Satellite System,全球导航卫星系统)接收机在探月任务中的应用。以探月工程三期为应用需求,开展地-月-地转移过程中的GNSS接收机可用性分析、GNSS信号特性分析;并针对低信噪比环境下的高灵敏度接收机系统应用进行设计,采用弱信号捕获算法和弱信号跟踪算法实现-175dBW的灵敏度;最终采用基于轨道动力学模型的卡尔曼滤波方法实现了GNSS自主定轨算法。仿真表明:GNSS接收机在60 000km以下的地-月转移和月-地转移弧段能够为探月飞行器提供100m以内位置精度的导航服务。     

脉冲干扰对软件接收机的影响分析

卫星信号经过长距离传播,信号能量损耗严重,到达地面的功率很弱,容易受到各种干扰的影响。脉冲干扰为常见的干扰类型,所以针对不同功率、不同周期,以及不同占空比的脉冲干扰信号,通过接收前端采集受脉冲干扰的GPS L1信号,利用软件接收机及多相关器生成技术,详细分析了脉冲干扰对接收机信号捕获与跟踪性能的影响。分析结果表明,周期为1ms的脉冲干扰信号,能对接收机产生强烈的干扰效果,捕获图中的噪声明显增大;跟踪过程中,载噪比和相关值突发性减小,造成跟踪数据异常。而长周期的脉冲信号仅在脉冲到达时影响接收机的捕获和跟踪,但由于信号跟踪不能连续进行,导致伪距观测量的不连续与导航数据不能正常解码,从而干扰接收机。     

直扩测控系统抗多址能力分析与验证

为了防止多址干扰造成接收机出现误捕和假锁,改善直接序列扩频测控系统抗多址干扰性能,在Gold码特性和扩频接收机性能分析的基础上,结合最大似然原理,对采用扩频体制测控系统的抗干扰能力进行了分析。为契合工程应用,采用仿真遍历结合理论分析的方式,对Gold码的互相关抑制能力理论值进行了工程修正。在分析捕获阶段的抗干扰捕获门限后,还分析了载噪比估计结果在正常锁定和假锁两种状态下的差异,给出了接收机对假锁状态的判决方法和门限。根据分析和仿真的结果,给出了系统设计约束条件和优化的接收机设计流程,作为测控系统和接收机设计的参考。     

Modeling and analysis for the GPS pseudo-range observable

In this paper, a digital system for the Global Positioning System (GPS) pseudo-range observable is modeled and analyzed theoretically. The observable is measured in a GPS receiver by accurately tracking the pseudorandom noise (PRN) code phase of the input GPS signal using a digital energy detector and a digital delay lock loop (DDLL). The following issues are presented: (1) mathematical modeling of the digital PRN code acquisition and tracking system, (2) the closed-form expression derivation for the detection and false-alarm probabilities of the acquisition process and for the variance of code phase tracking error, and (3) the linear and nonlinear performance analysis of the DDLL for optimizing the receiver structures and parameters with tradeoff between the tracking errors due to receiver dynamics and due to input noise     

基于喇曼散射的分布式光纤测温系统光接收机灵敏度的分析

在分布式光纤测温系统中,携有温度信息的喇曼散射光是极其微弱的,只有 n W量级,而温度变化引起的喇曼散射光的变化更加微弱。在对光接收机噪声分析的基础上,给出了该类应用条件下光接收机信噪比。指出了低信噪比下,AD的量化误差将随累加次数的增加而减小,同时 AD的有效位数将增加,给出了低信噪比下 AD有效位数的分析方法,并通过 MATLAB进行了验证,在此基础上,分析了光接收机的灵敏度,由此可以直接计算分布式光纤测温系统的测温精度。     

Performance analysis of GPS carrier phase observable

The accuracy analysis of Global Positioning System (GPS) carrier phase observable measured by a digital GPS receiver is presented. A digital phase-locked loop (DPLL) is modeled to extract the carrier phase of the received signal after a pseudorandom noise (PRN) code synchronization system despreads the received PRN coded signal. Based on phase noise characteristics of the input signal, the following performance of the first, second, and third-order DPLLs is analyzed mathematically: (1) loop stability and transient process; (2) steady-state probability density function (pdf), mean and variance of phase tracking error; (3) carrier phase acquisition performance; and (4) mean time to the first cycle-slipping. The theoretical analysis is verified by Monte Carlo computer simulations. The analysis of the dependency of the phase input noise and receiver design parameters provides with an important reference in designing the carrier phase synchronization system for high accuracy GPS positioning     

GPS C/N/sub 0/ estimation in the presence of interference and limited quantization levels

The carrier-to-noise density ratio (C/N₀) is considered an important parameter describing the GPS receiver performance. This paper compares the performance of two popular coarse-acquisition (C/A) C/N₀ algorithms appearing in literature: the variance summing method (VSM) (Psiaki et al., 2003, Psiaki, 2001), and the power ratio method (PRM) (Van Dierendonck, 1996, Sayre, 2003), in terms of their estimates in 1) additive white Gaussian noise (AWGN), 2) narrowband continuous wave interference (CWI), 3) their response to quantization and saturation effects, and their 4) dynamic range. The algorithms were implemented as a part of a software receiver. Two LI GPS data sets are examined; one was obtained from a GPS raw data collection setup, while the other was obtained from a GPS signal simulator. The collected set was stored with almost constant C/N₀ level while the simulated one contained variable C/N₀ levels. The effect of adding AWGN on the C/N₀ estimate was directly proportional with the noise power. The C/N₀ estimates suffered more when the CWI frequency was closer to the IF of the receiver. The PRM suffered from saturation at higher C/N₀ levels. The VSM showed good tracking at high C/N₀ levels and better immunity to limited quantization levels, while its C/N₀ estimate suffered from rapid fluctuations in power levels when sudden power steps occurred     

北斗导航接收机高增益相干积分算法

近年来,针对弱信号的高灵敏度接收机已逐渐成为国内外的研究热点。加长相干积分时间可以提高信噪比,从而跟踪到更弱的信号。但是,北斗导航接收机跟踪环路并不可以无限加长相干积分时间,相干积分时间的长短和功效还受到卫星导航电文比特跳变的限制。为了消除导航电文比特跳变对相干积分的影响,提出了一种改进的基于最大似然估计的北斗信号位同步方法,完成位同步后再利用先猜后检的方法便可以实现长相干积分。利用软件接收机进行编程设计,仿真结果表明：该长相干积分算法能够稳定可靠地实现对弱信号的跟踪,20ms相干积分环路信噪比约提升12dB,40ms相干积分环路信噪比约提升15dB,80ms相干积分环路信噪比约提升17dB,提高了北斗导航接收机的灵敏度。     

SNR-based multipath error correction for GPS differential phase

Carrier phase multipath is currently the limiting error source for high precision Global Positioning System (GPS) applications such as attitude determination and short baseline surveying. Multipath is the corruption of the direct GPS signal by one or more signals reflected from the local surroundings. Multipath reflections affect both the carrier phase measured by the receiver and signal-to-noise ratio (SNR). A technique is described which uses the SNR information to correct multipath errors in differential phase observations. The potential of the technique to reduce multipath to almost the level of receiver noise was demonstrated in simulations. The effectiveness on real data was demonstrated with controlled static experiments. Small errors remained, predominantly from high frequency multipath. The low frequency multipath was virtually eliminated. The remaining high frequency receiver noise can be easily removed by smoothing or Kalman filtering     

Multicomponent receiver architectures for GPS interference suppression

The global positioning system (GPS) is a one-way satellite-based navigation system employing spread-spectrum techniques that is widely used for commercial and military applications. Although the very low signal-to-noise ratio (SNR) is handled by the large spreading gain, GPS is susceptible to high-power interference signals and various types of jammers. We propose multicomponent receiver architectures for GPS interference suppression. A conventional antenna system is first considered which utilizes a minimum-variance distortionless-response (MVDR) beam former and assumes that the GPS signal angle of arrival (AOA) and the antenna model are known at the receiver. However, this receiver is sensitive to AOA estimation errors and can have a high computational complexity. This sensitivity problem is eliminated by a multicomponent system based on a multistage matched filter (MF). Since this MF receiver also has a high computational complexity because the jammer AOAs must be estimated, we introduce a blind interference canceler based on the constant modulus (CM) array that is insensitive to AOA estimation errors and has a low computational complexity. Computer simulations are provided to illustrate the performance of the various systems for interference suppression in example signal scenarios.