超声磨料对TC4钛合金电火花加工表面质量的影响

为改善TC4钛合金电火花加工表面质量,减少表面微裂纹、重熔层等表面缺陷,提出了基于电极振动的超声磨料电火花复合加工方法。在煤油工作液中混入12g/L的SiC磨料粉,进行了有无超声磨料作用的窄脉冲(脉宽小于1μs)电火花加工的表面粗糙度对比实验研究。实验结果表明:SiC磨料的超声振动作用使零件表面粗糙度Ra由0.5μm降到0.2μm左右;重熔层厚度、表面裂纹的扫描电子显微镜(SEM)照片显示,超声磨料作用使重熔层厚度减薄20～30μm,表面微裂纹得到有效控制;机理分析认为工作液高频振动及磨料对工件的冲击作用,是改善TC4钛合金电火花加工表面质量的主要原因。研究表明磨料的超声振动作用可显著改善TC4钛合金电火花加工的表面质量。     

高速走丝电火花线切割表面条纹的成因研究

分析了高速走丝电火花线切割加工时可通过电极丝空间位置稳定性的改善及选用具有良好洗涤能力的工作介质进行条纹消除的机理.并研究指出在大能量切割时,选用复合工作液以喷射的方式进行冷却,可以大大提高极间的洗涤性能,达到消除表面烧伤纹的目的.     

基于电火花-电解复合加工方法的微小孔制造

航空发动机涡轮叶片气膜冷却孔的制造一直是难点所在。提出了微小孔电火花-电解同步复合加工方法,通过电火花加工和电化学溶解同步进行,实现小孔的高效无重铸层制造。针对电火花-电解复合加工方法进行了试验研究,观测了复合加工过程中的试验现象,研究了加工过程中的电压电流波形和加工产物成分,计算了电化学溶解作用占复合加工材料去除量的比例,分析了工作液电导率对电极损耗的影响,比较了复合加工与纯电火花加工后的微小孔加工质量。试验结果表明,电火花-电解复合加工可以在微小孔制造完成的同时,有效去除孔壁上的重铸层。提出的方法可以为实现航空发动机涡轮叶片气膜冷却孔的高效无重铸层制造提供新的解决途径,并可用于其他微小群孔类零部件的加工。     

挠性接头电火花线切割加工工艺探索

为了提高挠性陀螺中挠性接头细颈加工精度,减小加工表面残余应力,提出了多次切割,控制线切割走丝轨迹等一系列工艺措施。     

超声电解复合微细加工硬质合金试验研究

超声电解复合微细加工工艺具有效率高、精度高、环保安全等优点,在硬质合金材料微结构加工方面具有一定的技术优势和发展潜力.本文阐述了超声电解复合微细加工机理和试验装置,对硬质合金材料进行了多组对比工艺试验,分析了加工电压、进给压力、电解液等加工参数对加工效果的影响,优化了加工参数和加工条件,提高了硬质合金微结构的微细加工精度.     

难加工材料的复合加工研究

一、前言 由于工业迅速发展,硬质合金、纯钨、钛合金等材料的应用越来越广泛,在机械制造、石油钻探、兵器、宇航和电子等部门常常遇到这些材料的加工问题。对于上述材料使用常规的机械加工方法极其困难,虽然可用通常的电火花加工方法解决,但效率极低,有的根本无法加工,如深小孔加工。为此,我们从1981年开始采用以水为基的复合工作液和特殊的脉冲电源,进行了难加工材料的电火花电解复合加工小孔的研究工作,现已取得良好的效果。在加工φ2～φ0.5毫米小孔时,加工速度:硬质合金材料为4～10毫米/分;纯钨材料为2～4毫米/分;钛合金、耐热合金材料为12～24毫米/分;对于钢材料的加工速度,一般达到或超过钛合金材料的加工速度。加工粗糙度约为,加工孔的深径比可达60倍以上。     

慢走丝线切割电解锈蚀放电状态的分析和控制

电解锈蚀放电状态在慢速走丝线切割加工过程中的危害十分严重．它不仅影响工件的表面精度和机械强度，而且还影响加工速度．导致电解锈蚀放电状态的主要原因是阳极金属溶解和工作液电解现象．本文主要研究预防阳极金属溶解和工作液电解的方法．还介绍了一种慢走丝线切割控制电解锈蚀放电状态的电源装置。     

线切割粗精复合加工智能化脉冲电源的研制

为了解决高速走丝线切割加工中高的切割速度与低的加工表面粗糙度值不能同时兼顾的矛盾，本文首次提出了线切割粗精复合加工的概念，并研制成功了线切割粗精复合加工智能化高频脉冲电源。该电源设有工艺参数数据库，具有自选加工规范的功能。     

超细晶硬质合金加工机理及加工性能

围绕超细晶硬质合金精密磨削加工、在线电解修整磨削加工、电火花加工、超声复合加工、激光复合加工等加工方法,系统综述了超细晶硬质合金的加工机理和加工性能,并展望了超细晶硬质合金高效精密加工未来的研究重点。     

以复合工作液为放电介质的低速走丝电火花线切割可行性研究

从典型放电波形分析了电火花线切割加工的极间放电特征,对高速走丝电火花线切割放电机理进行了探讨,通过对高速走丝线切割放电间隙、走丝速度对切割效率及表面质量影响的分析,得出了以复合工作液为放电介质的低速走丝电火花线切割是可行的结论。     

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。     

航空发动机管路测量数据分割方法

 为了提高航空发动机管路测量数据的反求建模效率,提出了一种区域增长分割算法。该方法主要是利用管路表面在曲面索引系数映射、主曲率映射、高斯映射上的特性,并基于均值漂移算法和遗传算法提出了区域分割算法中种子区域的选择策略。然后利用区域增长分割方法实现了对管路测量数据的分割。经过仿真和实测数据验证,所提管路分割算法具有较好的分割质量和效率。     

Abnormal Shape Mould Winding

为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。     

Interfacial Properties Modification of Carbon Fiber/ Polyarylacetylene Composites

This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered.     

Thermal Stresses and Cracks During the Growth of Large-sized Sapphire with SAPMAC Method

本文利用有限元法对冷心放肩微量提拉法(SAPMAC)生长大尺寸蓝宝石单晶过程中的热应力进行了模拟计算,应用临界缺陷理论解释了裂纹的萌生与扩展机理。研究表明,晶体内的热应力主要与晶体生长速率,环境温度和结晶取向有关;较大热应力多出现在结晶界面,放肩、收尾以及直径急剧变化等位置;最大热应力总是出现在籽晶与新生晶体的界面附近。裂纹将在临界缺陷位置产生,并在应力作用下沿a或m面扩展。计算结果与实验结果基本吻合,通过晶体生长系统和生长工艺的改进,对晶体的开裂问题得到了有效的抑制。     

Optimization Design System for Composite Structures Based on Grid Technology

To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm （PPGA） is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis （FEA） software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources.