钛合金TC4电火花诱导可控烧蚀高效磨削技术研究

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

钛合金TC4电火花诱导可控烧蚀高效磨削技术研究

王琳, 刘志东, 邱明波, 田宗军, 于建元

南京航空航天大学机电学院, 江苏南京 210016

收稿日期:2011-10-24 修回日期:2011-11-29 出版日期:2012-08-25 发布日期:2012-08-23
通讯作者: 刘志东 E-mail:liutim@nuaa.edu.cn
基金资助:
国家自然科学基金(51175256);航空科学基金(2011ZE52060);江苏省自然科学基金(BK2011732)

Study of TC4 Controllable Burned Efficient Grinding Induced by Electrical Discharge Machining

WANG Lin, LIU Zhidong, QIU Mingbo, TIAN Zongjun, YU Jianyuan

College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Received:2011-10-24 Revised:2011-11-29 Online:2012-08-25 Published:2012-08-23
Supported by:
National Natural Science Foundation of China (51175256);Aeronautical Science Foundation of China (2011ZE52060); Natural Science Foundation of Jiangsu Province (BK2011732).

摘要/Abstract

摘要： 利用大部分金属尤其是难加工金属的可燃特性,开发一种针对难加工金属材料的新加工工艺——电火花(EDM)诱导可控烧蚀高效磨削技术。采用开槽导电砂轮进行磨削加工,首先利用导电区域与加工材料产生电火花诱导放电并通入助燃氧气,使材料表面产生电火花引燃烧蚀并软化,然后将已烧蚀和软化的材料磨除,对钛合金TC4进行烧蚀磨削试验,并与常规电火花磨削和机械磨削进行对比,分析了材料去除率(RMM)、表面质量和机床主轴电机功率变化等指标。结果表明,在试验条件下,烧蚀磨削在放电利用率提高的同时可获得表面粗糙度为0.59 μm的加工表面,与机械磨削的表面粗糙度值相近,而相同条件下电火花磨削的表面粗糙度为1.29 μm。由于烧蚀后产生了软化层,在切深小于软化层厚度的条件下,相对于电火花磨削和机械磨削状况,烧蚀磨削主轴电机功率相比空载时的增加值分别降低了95.2%和96.8%。此工艺方法可大大提高难加工材料的可磨削性能。

关键词: 钛合金, 电火花, 烧蚀, 磨削, 表面质量

Abstract: A new process of efficient grinding technology is proposed which is based on electrical discharge machining (EDM) induced controllable burning of the workpiece to be machined. This process utilizes the flammability of a metal, especially difficult-cutting metal, and uses a slotted conductive wheel to grind. First, an EDM induced discharge is generated between the wheel and the material. Then the gap is filled with combustion-supporting oxygen to induce the material to burn and soften, and the burned and soften layer is subsequently removed. Work on titanium alloy TC4 by burned grinding is compared with EDM grinding and mechanical grinding. The material removal rate (MRR), surface quality, spindle motor power change, etc., are analyzed. The result shows that burned grinding can improve the discharge efficiency with an roughness of 0.59 μm, similar to that of mechanical grinding, while the roughness of EDM is 1.29 μm. Because there is a softened layer in burned grinding, when the cutting depth is less than the softened layer, the spindle motor power increase from the no-load condition of burned grinding is respectively 95.2% and 96.8% less as compared with EDM grinding and mechanical grinding. This technology may improve the grinding performance of difficult-cutting materials greatly.

Key words: titanium alloy, electrical discharge machining, burning, grinding, surface quality

中图分类号:

王琳, 刘志东, 邱明波, 田宗军, 于建元. 钛合金TC4电火花诱导可控烧蚀高效磨削技术研究[J]. 航空学报, 2012, 33(8): 1524-1530.

WANG Lin, LIU Zhidong, QIU Mingbo, TIAN Zongjun, YU Jianyuan. Study of TC4 Controllable Burned Efficient Grinding Induced by Electrical Discharge Machining[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2012, 33(8): 1524-1530.

参考文献

[1] Ren J X, Kang R K, Shi X K. Difficult-to-cut metarial grinding. Beijing: National Defense Industrial Press, 1999: 4-7. (in Chinese) 任敬心, 康仁科, 史兴宽. 难加工材料的磨削. 北京: 国防工业出版社, 1999: 4-7.
[2] Ren J X, Kang R K, Wang X B. Difficult-to-cut metarials grinding technology. Beijing: Electronics Industry Press, 2001: 6-9. (in Chinese) 任敬心, 康仁科, 王西彬. 难加工材料磨削技术. 北京: 电子工业出版社, 2001: 6-9.
[3] Ezugwu E O, Bonney J, Yamane Y. An overview of the machinability of aeroengine alloys. Journal of Materials Processing Technology, 2003, 134(2): 233-253.
[4] Chen W Y, Yuan Y F. Research progress of titanium cutting technology. Aeronautical Manufacturing Technology, 2010(15): 26-30. (in Chinese) 陈五一, 袁跃峰. 钛合金切削加工技术研究进展. 航空制造技术, 2010(15): 26-30.
[5] Song H W. Compulsive-cold grinding—new titanium grinding technology. Aeronautical Technology, 2001(6): 13-15. (in Chinese) 宋宏文. 强冷磨削——钛合金磨削新技术. 航空工艺, 2001(6): 13-15.
[6] Paul S, Chattopadhyay A B. The effect of cryogenic cooling on grinding forces. International Journal of Machine Tools & Manufacture, 1996, 36(1): 63-72.
[7] Paul S, Chattopadhyay A B. Effects of cryogenic cooling by liquid nitrogen jet on forces, temperature and surface residual stresses in grinding steels. Cryogenics, 1995, 35(8): 515-523.
[8] Fan M X, Zhang F H, Cui L L. Temperature field research of titanium grinding at low temperature by FEM. Diamond & Abrasives Engineering, 2002, 130(4): 20-23. (in Chinese) 范敏霞, 张飞虎, 崔玲丽. 用有限元法进行低温磨削钛合金温度场的研究. 金刚石与磨料磨具工程, 2002, 130(4): 20-23.
[9] Zhu B. ELLD mechanism research of steel bonded carbide and titanium. Harbin: School of Mechanical and Electronics Engineering, Harbin Institute of Technology, 2001. (in Chinese) 朱波. 钢结硬质合金与钛合金ELLD磨削技术及机理的研究. 哈尔滨: 哈尔滨工业大学机电工程学院, 2001.
[10] Hood R, Aspinwall D K, Voice W E. Creep feed grinding of a gamma titanium aluminide intermetallic alloy using SiC abrasives. Journal of Materials Processing Technology, 2007, 191(1-3): 210-214.
[11] Sato T, Waida T, Inoue H. High performance creep feed grinding of difficult-to-machine materials with new-type wheels. Bulletin of the Japan Society of Precision Engineering, 1990, 24(1): 39-44.
[12] Fu Y C, Xu H J. Workpiece surface temperature analysis when creep feed grinding using slotted wheel. China Mechanical Engineering, 2002, 13(7): 7-9. (in Chinese) 傅玉灿, 徐鸿钧. 开槽砂轮缓进给深切磨削时工件表层温度场解析. 中国机械工程, 2002, 13(7): 7-9.
[13] Sheng X M, Tang K, Yu J W. TC4 super high speed grinding technology research. Journal of Hunan University, 2008, 35(9): 28-32. (in Chinese) 盛晓敏, 唐昆, 余剑武. TC4 钛合金超高速磨削工艺试验研究. 湖南大学学报, 2008, 35(9): 28-32.
[14] Liu Z D. Metals controllable burning by EDM-induced efficient cutting technology: China, 201110192863.2011-11-30. (in Chinese) 刘志东.电火花诱导可控烧蚀金属材料高效切削加工方法: 中国, 201110192863.2011-11-30.
[15] Ge B J, Liang Y P, Wen J B. Electromechanics. Beijing: China Power Press, 2010: 14-16. (in Chinese) 戈宝军, 梁艳萍, 温嘉斌. 电机学. 北京:中国电力出版社, 2010: 14-16.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

钛合金TC4电火花诱导可控烧蚀高效磨削技术研究

Study of TC4 Controllable Burned Efficient Grinding Induced by Electrical Discharge Machining

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	罗圣峰, 王光健, 马小斌, 郑丽丽, 汪瑞军. 钛液滴作用下钛合金薄片火蔓延的数值模拟[J]. 航空学报, 2022, 43(9): 425652-425652.
[2]	李晖, 吕海宇, 邹泽煜, 罗忠, 马辉, 韩清凯. 热环境下纤维增强复合材料圆柱壳非线性振动分析与验证[J]. 航空学报, 2022, 43(9): 425642-425642.
[3]	郑辉, 邱雷, 袁慎芳, 杨晓飞, 卢绪龙, 薛兆鹏. C/C热防护结构高温气流损伤导波监测实验方法[J]. 航空学报, 2022, 43(8): 225659-225659.
[4]	姚燕生, 周瑞根, 张成林, 梅涛, 吴敏. 增材制造复杂金属构件表面抛光技术[J]. 航空学报, 2022, 43(4): 525202-525202.
[5]	武鑫磊, 刘永红, 亓梁, 赵莅龙, 纪仁杰. 镍基高温合金电火花辅助电弧高效铣削技术[J]. 航空学报, 2022, 43(4): 525615-525615.
[6]	赵一锦, 耿家宝, 杨晓冬. CFRPs电火花加工热影响区抑制方法[J]. 航空学报, 2022, 43(4): 525660-525660.
[7]	肖贵坚, 刘帅, 贺毅, 刘岗, 朱升旺, 宋沙雨. 钛合金激光砂带加工的离焦控制与表面形貌[J]. 航空学报, 2022, 43(4): 525603-525603.
[8]	穆宏鹏, 刘志东, 周顺程, 韩云晓, 邱明波. 极间介质模式对放电诱导烧蚀铣削影响[J]. 航空学报, 2022, 43(4): 525609-525609.
[9]	彭振龙, 张翔宇, 张德远. 航空航天难加工材料高速超声波动式切削方法[J]. 航空学报, 2022, 43(4): 525587-525587.
[10]	赵万生, 康小明, 顾琳, 奚学程, 张亚欧, 胡静, 赵福春. 放电加工技术在航空航天制造中的应用[J]. 航空学报, 2022, 43(4): 525936-525936.
[11]	陈波, 孟正, 马程远, 席鑫, 王昕欣, 檀财旺, 宋晓国. 扫描振镜激光TC4钛合金焊接性能及熔池流动行为[J]. 航空学报, 2022, 43(4): 525223-525223.
[12]	刘浩, 陈玉华, 章文滔. Ti/Al无针搅拌摩擦搭接点焊接头组织特征[J]. 航空学报, 2022, 43(2): 624680-624680.
[13]	邹祺, 叶逸云, 焦俊科, 吴志生, 徐子法, 张文武. 碳纤维增强热固性复合材料-钛合金激光连接接头性能分析[J]. 航空学报, 2022, 43(2): 625037-625037.
[14]	杨换平, 庄唯, 王耀勉, 剡文斌. 剧烈塑性变形对钛合金热氧化的影响[J]. 航空学报, 2021, 42(9): 424656-424656.
[15]	周印佳, 张志贤, 付新卫, 阿嵘. 再入飞行器烧蚀热防护一体化计算方法[J]. 航空学报, 2021, 42(7): 124520-124520.