涡轮导向器缘板安装缝隙泄漏特性数值模拟

刘亚非; 毛军逵; 徐瑞; 赵尊盛; 贺宜红; 李维

doi:10.13224/j.cnki.jasp.2015.06.021

涡轮导向器缘板安装缝隙泄漏特性数值模拟

doi: 10.13224/j.cnki.jasp.2015.06.021

1. 南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室, 南京 210016;
2. 中国航空工业集团公司中国航空动力机械研究所, 湖南株洲 412002

基金项目:

中央高校基本科研业务费专项资金(56XZA13085)

详细信息

作者简介:
刘亚非(1990-),男,甘肃天水人,硕士生,主要从事航空发动机涡轮叶栅流动与换热方面的研究.

中图分类号: V231.3
计量
- 文章访问数: 1334
- HTML浏览量: 2
- PDF量: 684
- 被引次数: 0
出版历程
- 收稿日期: 2013-12-11
- 刊出日期: 2015-06-28

Numerical simulation of leakage characteristic of assembled endwall slot of turbine guide vane

1. Jiangsu Province Key Laboratory of Aerospace Power System, College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China;
2. China Aviation Powerplant Research Institute, Aviation Industry Corporation of China, Zhuzhou Hunan 412002, China

摘要

摘要: 针对某航空发动机涡轮导向器,采用数值模拟的方法研究了缘板安装缝隙泄漏流对叶栅通道流场结构及叶栅性能参数的影响,对比分析了不同泄漏流压力、缝隙宽度及缝隙相对位置条件下的泄漏量,及其对叶栅性能参数的影响规律.研究发现:在压差作用下冷气通过缘板安装缝隙进入燃气主流通道并在中段的位置形成螺旋涡系,对端壁二次流产生明显影响,其作用效果沿叶高方向逐渐降低,最大影响区域为44.44%叶高.计算结果表明:随着泄漏流压力的提高、缝隙宽度的增加、缝隙与发动机主轴方向夹角的变大,叶栅的能量损失系数和泄漏量都呈现出了单调增加的趋势.在研究的参数范围内,涡轮缘板安装缝隙导致的泄漏流可使叶栅的能量损失系数增加14%~62%.
- 涡轮导向器 /
- 端壁 /
- 缘板安装缝隙 /
- 二次流 /
- 泄漏流 /
- 能量损失系数
Abstract: Numerical simulations were applied to study the leakage flow of assembled endwall slot of turbine guide vane of an aero-engine. The effects of leakage flow on the structure of flow field of cascade passage and performance parameters of the cascade were also discussed. The leakage flow pressures, the slot width and position of the slot were changed to investigate the rules of leakage flow rate and energy loss coefficient varying with these parameters and discover the effect rules. It is found that the leakage can appear due to different pressures between cooling air and gas, spiral vortex system is formed in the middle position of the slot at the same time, and the leakage flow affects the secondary flow around the endwall significantly. The effect decreases along the direction of blade height and the largest region is up to 44.44% of the blade height. With the increase of leakage flow pressure, the slot width and the angle between the slot and major axis of engine, the energy loss coefficient of the cascade and the leakage flow rate increase monotonically. Numerical results show that the energy loss coefficient of the cascade increases by 14%-62% because of the leakage flow through the slot of the endwall in the parameter range of present study.
- turbine guide vane /
- endwall /
- assembled endwall slot /
- secondary flow /
- leakage flow /
- energy loss coefficient

HTML

参考文献(31)

[1]	Dunham J.A review of cascade data on secondary losses in turbines[J].Journal of Mechanical Engineering Science,1970,12(1):48-59.
[2]	Coull J D,Hodson H P.Predicting the profile loss of high-lift low pressure turbines[J].Journal of Turbomachinery,2012,134(2):021002.1-021002.14.
[3]	Moore J,Adhye R Y.Secondary flows and losses downstream of a turbine cascade[J].Journal of Engineering for Gas Turbines and Power,1985,107(4):961-968.
[4]	Langston L S,Nice M L,Hooper R M.Three-dimensional flow within a turbine cascade passage[J].Journal of Engineering for Gas Turbines and Power,1977,99(1):21-28.
[5]	Paniagua G,Yasa T,La Loma A D,et al.Unsteady strong shock interactions in a transonic turbine:experimental and numerical analysis[J].Journal of Propulsion and Power,2008,24(4):722-731.
[6]	Langston L S.Crossflows in a turbine cascade passage[J].Journal of Engineering for Gas Turbines and Power,1980,102(4):866-874.
[7]	董志锐,刘松龄.涡轮叶栅端壁区的流动显示[J].中国科学基金,1999,13(5):296-297. DONG Zhirui,LIU Songling.Flow visualization of endwall area in turbine cascade[J].Bulletin of National Science Foundation of China,1999,13(5):296-297.(in Chinese)
[8]	Denton J,Pullan G.A numerical inverstigation into the sources of endwall loss in axial flow turbines[R].ASME Paper GT2012-69173,2012.
[9]	Deich M E,Zaryankin A D,Filippov G A,et al.Method of increasing the efficiency of turbine stages with short blades[M].Manchester,UK:Associated Electrical Industries Limited,1960.
[10]	Morris A W H,Hoare R G.Secondary loss measurements in a cascade of turbine blades with meridional wall profiling[R]ASME Paper 75-WA/GT-13,1975.
[11]	Rose M G.Non-axisymmetric endwall profiling in the HP NGV’s of an axial flow gas turbine[R].ASME Paper 94-GT-249,1994.
[12]	Kawai T,Shinoki S,Adachi T.Secondary flow control and loss reduction in a turbine cascade using endwall fences[J].International Journal of Japan Society of Mechanical Engineers,1989,32(3):375-387.
[13]	Brundage A L,Plesniak M W,Ramadhyani S.Influence of coolant feed direction and hole length on film cooling jet velocity profiles[R].ASME Paper 99-GT-035,1999.
[14]	Karni J,Goldstein R J.Surface injection effect on mass transfer from a cylinder in crossflow:a simulation of film cooling in the leading edge region of a turbine blade[J].Journal of Turbomachinery,1990,112(3):418-427.
[15]	Bogard D G.Evaluation of pressure side film cooling with flow and thermal field measurements:Part Ⅰ showerhead effects[J].Journal of Turbomachinery,2002,124(4):670-677.
[16]	Blair M F.An experimental study of heat transfer and film cooling on large-scale turbine endwalls[J].Journal of Heat Transfer,1974,96(4):524-529.
[17]	Friedrichs S,Hodson H P,Dawes W N.Distribution of film-cooling effectiveness on a turbine endwall measured using the ammonia and diazo technique[J].Journal of Turbomachinery,1996,118(4):613-621.
[18]	Friedrichs S,Hodson H P,Dawes W N.Aerodynamic aspects of endwall film-cooling[J].Journal of Turbomachinery,1997,119(4):786-793.
[19]	刘高文,刘松龄,朱惠人,等.涡轮叶栅前缘上游端壁气膜冷却的传热实验研究[J].航空动力学报,2001,16(3):249-255. LIU Gaowen,LIU Songling,ZHU Huiren,et al.Endwall heat transfer and film cooling measurements in a turbine cascade with injection upstream of leading edge[J].Journal of Aerospace Power,2001,16(3):249-255.(in Chinese)
[20]	刘高文,刘松龄,许都纯,等.涡轮叶栅前缘上游端壁气膜冷却的流场实验研究[J].航空动力学报,2001,16(2):135-141. LIU Gaowen,LIU Songling,XU Duchun,et al.Experimental investigation of flow fields in a turbine cascade with endwall film-cooling upstream of leading edge[J].Journal of Aerospace Power,2001,16(2):135-141.(in Chinese)
[21]	吕品,王子健,闻洁.出流结构对涡轮叶栅端壁气膜冷却效率数值研究[J].航空动力学报,2010,25(5):981-986. LV Pin,WANG Zijian,WEN Jie.Numerical study on film-cooling effectiveness on endwall of a turbine cascade by different film-cooling jet structures[J].Journal of Aerospace Power,2010,25(5):981-986.(in Chinese)
[22]	Goldman L J,McLallin K L.Effects of endwall cooling on secondary flows in turbine stator vanes[R].Advisory Group for Aerospace Research and Development,AGARD CPP-214,1977.
[23]	Nicklas M.Film-cooled turbine endwall in a transonic flow field:Part Ⅱ heat transfer and film-cooling effectiveness[J].Journal of Turbomachinery,2001,123(4):720-729.
[24]	Knost D G,Thole K A.Computational predictions of endwall film-cooling for a first stage vane[J].International Journal of Turbo and Jet Engines,2005,22(1):41-58.
[25]	Lampart P,Yershov S,Rusanov A,et al.Tip leakage/main flow interactions in multi-stage HP turbines with short-height blading[R].ASME Paper GT2004-53882,2004.
[26]	Paniagua G,Dénos R,Almeida S.Effect of the hub endwall cavity flow on the flow-field of a transonic high-pressure turbine[J].Journal of Turbomachinery,2004,126(4):578-586.
[27]	Owen J M,Rogers R H.Flow and heat transfer in rotating-disc systems:Volume 1 rotor-stator systems[M].Hoboken,US:John Wiley and Sons Incorporated,1989.
[28]	Gridley M C,Walker S H.Inlet and nozzle technology for 21st century fighter aircraft[R].ASME Paper 96-GT-244,1996.
[29]	Hylton L D,Mihelc M S,Turner E R,et al.Analytical and experimental evaluation of the heat transfer distribution over the surfaces of turbine vanes[R].NASA-CR-168015,1983.
[30]	陈懋章.粘性流体力学[M].北京:高等教育出版社,2002.
[31]	黄大革,张根烜.微尺度流动模型研究[J].电子机械工程,2007,23(3):59-61. HUANG Dage,ZHANG Genxuan.Study on the micro-scale flow model[J].Electro-Mechanical Engineering,2007,23(3):59-61.(in Chinese)