翘曲端壁对大折转角压气机叶栅流动的影响

崔可; 宋彦萍; 刘华坪; 陈浮

doi:10.13224/j.cnki.jasp.2015.05.027

翘曲端壁对大折转角压气机叶栅流动的影响

doi: 10.13224/j.cnki.jasp.2015.05.027

哈尔滨工业大学能源科学与工程学院, 哈尔滨 150001

基金项目:

国家自然科学基金(51121004)

详细信息

作者简介:
崔可(1987-),男,湖南湘潭人,博士生,主要从事叶轮机械气动热力学研究.

中图分类号: V231.1
计量
- 文章访问数: 866
- HTML浏览量: 2
- PDF量: 625
- 被引次数: 0
出版历程
- 收稿日期: 2013-12-17
- 刊出日期: 2015-05-28

Influence of bump end wall on cascade flow of high turning-bowed compressor

School of Energy Science and Engineering, Harbin Institute of Technology, Harbin 150001, China

摘要

摘要: 研究了翘曲端壁对大折转角压气机叶栅流动的影响.结果表明:翘曲最高点位于压力面时效果较好,翘曲高度为2%叶高时出口总压损失下降约5.8%;而翘曲最高点位于压力面与吸力面之间时效果则不理想;翘曲高度为5%叶高、翘曲最高点距压力面为0.25倍节距时出口总压损失增加约3.4%,此时端壁附近压力梯度呈先顺后逆变化,低能流体由压力面端区迁移至10%叶高处与吸力面附近低能流体汇合,增加了流道内二次流强度;当来流攻角不为零时,下端壁翘曲所构造的反向压差对于减小二次流强度、降低出口总压损失的效果仍比较明显,+3°攻角下出口总压损失减小约5.6%,-3°攻角下出口总压损失减小约3.5%,但同时其导致的负荷沿径向重新分配也将使得上端壁附近流动状况也发生改变.
- 翘曲 /
- 端壁造型 /
- 大折转角 /
- 压气机 /
- 二次流
Abstract: The influence of bump end wall on flow cascade of high turning-bowed compressor was investigated. The result shows that the influence is better when the bump salient point is located on the pressure side, and the outlet total pressure loss obtains 5.8% reduction when the height of bump is 2% of the whole blade height. However, a poor result may be obtained as the salient bump point was located between the pressure side and the suction side. When the salient bump point of the end wall profile is 25% pitch away from the pressure side and the height of bump is 5% of the whole blade height, the outlet total pressure loss may get an increase of 3.4%, and the pressure gradient near the end wall changes from positive to negative, thus making the low energy fluid near the end wall of the pressure side transfer to the position of 10% of the whole blade height on the suction side and join into the low energy fluid near the suction side, strengthening the local secondary flow. As the angle of attack changes, the reverse differential pressure constructed by the lower bump end wall can still obviously reduce the intensity of the local secondary flow as well as the outlet total pressure loss; the outlet total pressure loss obtains a 5.6% reduction at the angle of attack of +3° and a 3.5% at the angle of attack of -3°. Meanwhile, the redistribution of the load along the radial direction due to this differential pressure will also change the flow near the upper end wall.
- bump /
- end wall profile /
- high turning-bowed /
- compressor /
- secondary flow

HTML

参考文献(18)

[1]	吴吉昌, 卢新根, 朱俊强.非轴对称端壁下高负荷压气机叶栅二次流动分析[J].航空动力学报, 2011, 26(6):1364-1369. WU Jichang, LU Xingen, ZHU Junqiang.Secondary flow analysis for non-axisymetric endwall on the high-load compressor cascade[J].Journal of Aerospace Power, 2011, 26(6):1364-1369.(in Chinese)
[2]	伊卫林, 黄鸿雁, 韩万金.基于数值优化的跨音速压气机动叶三维设计[J].燃气轮机技术, 2006, 19(2):34-38. YI Weilin, HUANG Hongyan, HAN Wanjin.Three dimensional design of transonic compressor rotor using numerical optimization[J].Gas Turbine Technology, 2006, 19(2):34-38.(in Chinese)
[3]	刘小民, 高健.弯曲叶片对跨音速轴流压气机性能影响的数值研究[J].流体机械, 2010, 38(2):13-17. LIU Xiaomin, GAO Jian.Numerical investigation of the effect of bowed blade on the performance of transonic axial compressor[J].Fluid Machinery, 2010, 38(2):13-17.(in Chinese)
[4]	游斌.前缘弯掠(扭)斜流转子内流机制的数值分析及实验研究[D].武汉:华中科技大学, 2004. YOU Bin.Numerical analysis and experimental research on the internal flow mechanism of the leading edge skewed swept diagonal rotor[D].Wuhan:Huazhong University of Science and Technology, 2004.(in Chinese)
[5]	Howell A R.Fluid dynamics of axial compressors[J].Proceedings of the Institution of Mechanical Engineers, 1945, 153:441-452.
[6]	Rose M G.Non-axisymmetric end wall profiling in the HP NGVs of an axial flow gas turbine[R].ASME Paper 94-GT-249, 1994.
[7]	郑金, 李国君, 李军, 等.一种新的非对称端壁成型方法的数值研究[J].航空动力学报, 2007, 22(9):1487-1491. ZHENG Jin, LI Guojun, LI Jun, et al.Numerical research on a new non-axisymmetric end wall profiling method[J].Journal of Aerospace Power, 2007, 22(9):1487-1491.(in Chinese)
[8]	孙皓, 宋立明, 李军, 等.小展弦比叶栅非轴对称端壁造型及气动性能的数值研究[J].西安交通大学学报, 2012, 46(11): 6-11. SUN Hao, SONG Liming, LI Jun, et al.Numerical investigations on nonaxisymmetric end wall profiling and aerodynamic performance of a low aspect ratio cascade[J].Journal of Xi'an Jiaotong University, 2012, 46(11):6-11.(in Chinese)
[9]	胡书珍, 卢新根, 张宏武, 等.亚音速轴流压气机转子非轴对称轮毂端壁的数值研究[J].工程热物理学报, 2009, 30(3):385-388. HU Shuzhen, LU Xingen, ZHANG Hongwu, et al.Numerical investigation on a subsonic axial-flow compressor rotor with the implementation of the non-axisymmetric hub end wall[J].Journal of Engineering Thermophysics, 2009, 30(3):385-388.(in Chinese)
[10]	王睿.非对称端壁对扩压叶栅性能影响的数值研究[D].哈尔滨:哈尔滨工业大学, 2012. WANG Rui.Numerical investigation on effect of applying non-axisymmetric endwall on compressor cascade performance[D].Harbin:Harbin Institute of Technology, 2012.(in Chinese)
[11]	李国君, 马晓永, 李亮.非轴对称端壁成型及其对叶栅损失影响的数值研究[J].西安交通大学学报, 2005, 39(11):1169-1172. LI Guojun, MA Xiaoyong, LI Liang.Non-axisymetric end wall profiling and numerical investigation of its effect on the turbine cascade loss[J].Journal of Xi'an Jiaotong University, 2005, 39(11):1169-1172.(in Chinese)
[12]	Harvey N W, Mark M G, Taylor M D, et al.Non-axisymetric turbine end wall design:Part 1 three dimensional linear design system[R].ASME Paper 99-GT-337, 1999.
[13]	Harland J, Smith D G.A design method for the profiling of end walls in turbines[R].ASME Paper GT-2001-30433, 2001.
[14]	李国君, 任光辉, 马晓永, 等.叶栅非轴对称端壁成型技术的初步研究[J].工程热物理学报, 2006, 27(增刊1):97-100. LI Guojun, REN Guanghui, MA Xiaoyong, et al.The preliminary study of non-axisymmetric end wall design in a cascade[J].Journal of Engineering Thermophysics, 2006, 27(suppl.1):97-100.(in Chinese)
[15]	宋彦萍, 陈焕龙, 陈浮, 等.扩压叶栅中带切向孔叶片的研究[J].工程热物理学报, 2007, 28(增刊1):105-108. SONG Yanping, CHEN Huanlong, CHEN Fu, et al.Numerical study on the performance of compressor cascade with air injection[J].Journal of Engineering Thermophysics, 2007, 28(suppl.1):105-108.(in Chinese)
[16]	冯冬民.空隙射流对大折转角压气机叶栅分离流动的影响[D].哈尔滨:哈尔滨工业大学, 2009. FENG Dongmin.Investigation in effects of air-injection on flow separation in high turning compressor cascade[D].Harbin: Harbin Institute of Technology, 2011.(in Chinese)
[17]	刘华坪.DBD等离子体控制附面层流动分离机理研究[D].哈尔滨:哈尔滨工业大学, 2011. LIU Huaping.The DBD plasma effect on the boundary layer separation[D].Harbin:Harbin Institute of Technology, 2011.(in Chinese)
[18]	陈焕龙, 李得英, 俞建阳, 等.缝隙扩压叶栅近壁流场与流动损失实验[J].推进技术, 2013, 34(3):332-338. CHEN Huanlong, LI Deying, YU Jianyang, et al.Experimental investigation of near-wall flow and flow loss in compressor cascades with slots injection[J]. Journal of Propulsion Technology, 2013, 34(3):332-338.(in Chinese)